Summary of the content on the page No. 1
UNDERWATER CAMERA
WITH MONITOR
91309
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Summary of the content on the page No. 2
Specifications Battery Sealed, Lead Acid (with fuse) Maximum Camera Depth 65 Feet (Length of Cable) Overall Weight 11.85 Lbs. Camera Dimensions 1-5/8” W x 7” L x 3-7/8” H Camera Light Source Built-in Infrared LED Bulbs Input Voltage 12 Volts DC Camera Operating Temperature -20° to 120° F Camera Angle-of-View 83° (horizontal), 60° (vertical) Camera Depth-of-View 15” (approximate; in clear water) Monitor Image Black and White Monitor Picture Resolution 450 (TV Lines) Monitor Input Voltage 11 to 15
Summary of the content on the page No. 3
9. Maintain products with care. Keep products clean for better and safer performance. Follow instructions for changing accessories. Inspect cords periodically, and if damaged, have them repaired by an authorized technician. 10. Disconnect power. Unplug the system when not in use. 11. Stay alert. Watch what you are doing, use common sense. Do not operate any product when you are tired. 12. Check for damaged parts. Before using any product, any part that appears damaged should be carefully chec
Summary of the content on the page No. 4
Monitor and Underwater Camera Specific Safety Warnings 1. Keep the Monitor (2) out of the direct sunlight. Do not let it overheat, freeze, or be exposed to wet conditions. 2. Do not locate the Monitor (2) near radiators, ovens, or any other heat source. 3. Always handle the Monitor (2) and the Camera (1) with care. Do not allow either to experience shaking or strong vibration. Never use the Camera in surf, near a pier, rocks, or any other obstacle. 4. To allow air circulation, locate the
Summary of the content on the page No. 5
Operation (continued) Connecting the system (continued) 1. Set the Monitor (2) in a dry, stable position, out of the direct sunlight and in accordance with the operational warnings above. Set the Sunshade (8) on top of the Monitor (2). Just a few feet from the Camera (1), run the 65 Foot Cable (3) around a railing or post to keep the weight of the Camera (1) from dislodging the Monitor (2) from its stable position. Plug the 65 Foot Cable (3) into the Camera port (C1) on the back of the Monito
Summary of the content on the page No. 6
Maintenance 1. Always turn off the power and disconnect the unit when not in use. 2. Wipe all of the components to remove any moisture after each use. 3. Make sure the terminal contacts on the Battery (4) are clean and free of corrosion. 4. After six hours of use, charge the Battery (4) following the directions below. 5. Keep the Camera (1) lens clear of dirt or debris. FIGURE 5 (-) Negative (+) Positive Battery (4) Adapter (7) Never reverse the polarity when connecting the Battery (4) for
Summary of the content on the page No. 7
Assembly Drawing and Parts List Part No. Description 1 Camera 2 Monitor 3 65 Foot Cable (attached to Camera (1)) 4 Battery 5 Battery Cord 6 Case 7 Adapter 8 Sunshade Note: Adapter (7) and Sunshade (8) not shown. 6 5 3 4 2 1 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALI
