Summary of the content on the page No. 1
D-Link
DCS-900
Internet Camera
Manual
Version 1.10
Building Networks for People
(09/18/03)
Summary of the content on the page No. 2
Contents Package Contents ...............................................................3 Introduction ..........................................................................4 Hardware Installation ............................................................9 Security ..............................................................................10 Using the Setup Wizard .....................................................11 DCS-900 Configuration .............................................
Summary of the content on the page No. 3
Package Contents Contents of Package: • One DCS-900 Internet Camera • One Installation CD-ROM • One AC power adapter • One Camera Stand • One Category 5 Ethernet Cable If any of the above items are missing, please contact your reseller. System Requirements: Local Area Network: 10Base-T Ethernet or 100BaseTX Fast Ethernet Recommended: PC, Mac or Notebook to access the Internet Camera Web Configuration • Java Enabled and Compliant Web Browser (recommended) • CPU: Pentium III, 450
Summary of the content on the page No. 4
Introduction Congratulations on your purchase of the DCS-900 Internet Camera! The DCS-900 is a versatile and unique solution for your small office or home. Unlike a PC Camera, the DCS-900 is a stand-alone system with a built-in CPU and Web server that transmits high quality video images for monitoring. The DCS-900 can be accessed remotely, and controlled from any PC/Notebook over the Intranet or Internet via a web browser. The simple installation procedure and intuitive web-based interface of
Summary of the content on the page No. 5
Features & Benefits (continued) Web Configuration Using a standard Web browser, Administrators can configure and manage the Internet Camera directly from its own Web page via the Intranet or Internet. This means anytime, anywhere access to your DCS-900 from anywhere in the world! Remote Monitoring Utility The IPView Lite application adds enhanced features and functionality for the Internet Camera and allows administrators to configure and access the Internet Camera from a remote site via Intrane
Summary of the content on the page No. 6
Connections Rear Panel view Ethernet Cable Connector DC Power Connector Reset Button Network Cable Connector The DCS-900 features an RJ-45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5 UTP twisted-pair cable). The port supports the NWay protocol, allowing the DCS-900 to automatically detect or negotiate the transmission speed of the network. DC Power Connector The DC power input connector is labeled DC 5V with a single jack
Summary of the content on the page No. 7
Connections (continued) Bottom Panel view Stand Connector 7
Summary of the content on the page No. 8
LEDS LED stands for Light-Emitting Diode. Front view Power LED LAN LED Power LED The Power LED is positioned on the right side of the DCS-900 lens. Steady green confirms that the DCS-900 is powered ON. Note: There are three settings for the Power LED for monitoring purposes: Normal / Off / Dummy. Please refer to the DCS-900 Camera Configuration section for detailed information and usage. LAN LED The LAN LED is positioned on the right side of the DCS-900’s lens. It is located below the Power LED
Summary of the content on the page No. 9
Hardware Installation Attach the Swivel Stand Locate the stand connector on the bottom panel of the DCS-900 and screw on the swivel stand to the base of the DCS-900. Attach the External Power Supply Attach the external power supply to the DC power input connector located on the rear panel of the DCS-900 and connect it to your local power supply. Note: Power source is confirmed when the green LED Power Indicator located to the right of the lens on the DCS-900 is illuminated. Connect the Ethernet
Summary of the content on the page No. 10
Security To ensure the highest security and prevent unauthorized usage of the DCS-900, the Administrator has the exclusive privilege to authorize all users. The DCS-900 supports multi-level password protection/access to the DCS-900 that can be restricted by the Administrator for defined users who have a User Name and User Password. The Administrator can release a public User Name and Password so that when remote users access the DCS-900 they will be allowed to view the images transmitted by the
Summary of the content on the page No. 11
Using the Setup Wizard Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. Insert the D-Link DCS-900 Driver CD into your CD-ROM drive. When the autorun screen appears, click Install Wizard to begin the installa- tion. Click Next Click Yes 11
Summary of the content on the page No. 12
Using the Setup Wizard (continued) Click Next Click Finish To run the Setup Wizard, click on Start->Programs->DCS-900 Series Setup Wizard. Your camera’s IP Address will be displayed here if it is valid. Click Wizard to begin 12
Summary of the content on the page No. 13
Using the Setup Wizard (continued) You must change the Admin ID and Password immediately to protect your camera against unauthorized access. By default, the Admin ID and Password are blank. To change the Admin ID and Password, select both Change boxes and enter a New ID and New Password. Click Next The IP Address, Subnet Mask of your camera and Gateway must correspond with your network settings for you to access the camera. If you are unsure of what these settings should be, please check with
Summary of the content on the page No. 14
DCS-900 Configuration Web Configuration After completing the Setup Wizard, you are ready to use your camera. The web configuration utility is designed to easily access and configure your DCS-900. From the Web Browser, enter the IP address that you assigned to your DCS-900 to access the Welcome screen of the DCS-900. Press Enter. Note: The PC’s IP address must correspond with the DCS-900’s IP address in the same segment (i.e. PC=192.168.0.5, Camera=192.168.0.20) for the two devices to communicat
Summary of the content on the page No. 15
DCS-900 Configuration (continued) Configuration Click on Setup from the Home screen to access the settings required for the DCS-900. There will be several options in the Configuration page to choose from to setup your DCS-900 and they are as follows: Advanced • System • Video Tools • Admin • Time • Default Status Help 15
Summary of the content on the page No. 16
DCS-900 Configuration (continued) Advanced > System The System menu allows you to configure and set up your DCS-900 for operation. If you already set up your camera using the Setup Wizard, you may view/change your settings here. To access the System menu, click on the Advanced Tab in the menu bar, then the System tab in the left hand bar and the System screen will appear as illustrated below: 16
Summary of the content on the page No. 17
DCS-900 Configuration (continued) Advanced > System Camera Name: This field is used for entering a descriptive name for the camera. The default setting for the Camera Name is CS-xxxxxx, where xxxxxx are the last six digits of the MAC Address. The maximum length is 32 characters (Printable ASCII). Location: This field is used for entering a descriptive name for the location used by the DCS-900. IP Assignment: Important Information Access to the Internet Camera is gained by assigning a proper IP A
Summary of the content on the page No. 18
DCS-900 Configuration (continued) Advanced > System Assign Automatically Using Important This options is recommended only for advanced users and network administrators since it may be difficult to determine the IP Address of the unit after the IP Address has been automatically asssigned. It is recommended that an IP Address be assigned manually. If your network is using RARP, BOOTP, or DHCP Server you can Click Assign Automatically Using and click on RARP, BOOTP or DHCP. Under this setting the
Summary of the content on the page No. 19
DCS-900 Configuration (continued) Advanced > System The default setting for the LED control is Normal. When you have configured the LED control the correct illumination will be applied after 1 minute. Note: The three LED options allow the Administrator to customize the LEDs for discreet camera operation in surveillance scenarios. In Normal Mode, the LED indicator functions normally. Under Off Mode, the LED indicators are both OFF during active monitoring. In Dummy Mode, the LEDs are active and
Summary of the content on the page No. 20
DCS-900 Configuration (continued) Advanced > System The Transfer Image Port must also be assigned a port number for multiple camera installation, beginning with Port 8482: Internet Camera 1 – IP 192.168.0.101, second Web Port 8482 Internet Camera 2 – IP 192.168.0.102, second Web Port 8483 Internet Camera 3 – IP 192.168.0.103, second Web Port 8484 Internet Camera 4 – IP 192.168.0.104, second Web Port 8485 Internet Camera 5 – IP 192.168.0.105, second Web Port 8486 Note: If you are installing multi
