Summary of the content on the page No. 1
SkyIPCam310
Power Over Ethernet Network Camera
Model # AICP310
User’s Manual
Ver 1A
Summary of the content on the page No. 2
Table of Contents ABOUT THIS GUIDE...................................................................................................................2 1. INTRODUCTION......................................................................................................................3 1.1 FEATURES AND BENEFITS .......................................................................................................3 1.2 UNPACKING THE PACKAGE ...................................................
Summary of the content on the page No. 3
0 About This Guide This manual provides instructions and illustrations on how to use your SkyIPCam310 PoE Network Camera, includes: Chapter 1, Introduction, provides the general information on the camera. Chapter 2, Installation, describes the hardware and software installation procedure for the SkyIPCam310. Chapter 3, Security, explains the security feature of the camera. Chapter 4, Application of the Camera, provides the illustrations of the camera’s applications. Chapter 5, Us
Summary of the content on the page No. 4
1 1. Introduction Thank you for purchasing the SkyIPCam310 PoE Network Camera, a camera device that can be connected directly to an Ethernet or Fast Ethernet network. Compared to the conventional PC Camera, the SkyIPCam310 features a built-in CPU and web-based solutions that can provide a cost-effective solution to transmit real-time high-quality video images and sounds for monitoring. It can be managed remotely, accessed and controlled from any PC/Notebook over the Intranet or Interne
Summary of the content on the page No. 5
needs. When the external device is connected, you could configure the settings and control the device from the RS485 window of Web Configuration Utility. Remote Utility The powerful IPView Pro application assigns the administrator with a pre-defined user ID and password, allowing the administrator to modify the camera settings from the remote site via Intranet or Internet. When new firmware is available, you can also upgrade remotely over the network for added convenience. Users are also
Summary of the content on the page No. 6
1.3 System Requirements Networking 10Base-T Ethernet or 100Base-TX Fast Ethernet. Accessing the Camera For Web Browser Users Operating System: Microsoft® Windows® 98SE/ME/2000/XP/Vista CPU: Intel Celeron 1.1GHz or above (Intel Pentium 4 is preferred) Memory Size: 128MB or above Resolution: 800x600 or above Microsoft® Internet Explorer 5.0 or above For IPView Pro Application Users Operating System: Microsoft® Windows® 2000/XP/Vista. CPU: Intel Celeron 1.1GHz or above (Inte
Summary of the content on the page No. 7
3. Internal MIC The built-in omni-directional microphone allows the camera to receive sound and voice. Rear Panel 2. Reset Button 3. I/O Connector 1. Network Cable Connector 4. DC Power Connector 1. Network Cable Connector The SkyIPCam310’s rear panel features an RJ-45 connector for connections to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5 twisted-pair cable). The port supports the N-Way protocol and “Auto-MDIX” function,
Summary of the content on the page No. 8
Top/Bottom Panel Top Panel Screw Hole Bottom Panel Screw Hole Screw Hole Located on the top/bottom panel of the camera, the screw hole is used to connect the camera stand onto the camera by attaching the screw head on the camera stand into the screw hole of the camera. 7
Summary of the content on the page No. 9
2 2. Hardware Installation 2.1 Attaching the Camera to the Stand The SkyIPCam310 comes with a camera stand (optional), which is equipped with a swivel ball screw head that can be attached to the camera's bottom screw hole. Attach the camera stand to the camera and station it for your application. There are three holes located in the base of the camera stand allowing the SkyIPCam310 to be mounted on the ceiling or any wall securely. 2.2 Connecting the Ethernet cable Connect an
Summary of the content on the page No. 10
2.4 Setting up the Camera Installing the Setup Wizard Step 1 Insert the provided CD and wait for the autorun screen to appear. Step 2 Click on Install Setup Wizard. Note: If the autorun screen does not appear automatically, go to Start, Run, type D:\Wizard\Setup.exe (where D is the letter of your CD drive) and click OK. Step 3 Click Next. 9
Summary of the content on the page No. 11
Step 4 Click Yes to accept the License Agreement. Step 5 Click Next to accept the default Destination Folder. Step 6 Click Finish to complete the installation. 10
Summary of the content on the page No. 12
Using the Setup Wizard Step 1 Go to Start > (All) Programs > AirLink101 IP Camera Setup Wizard > AirLink101 IP Camera Setup Wizard. Step 2 Select the IP Camera you want to configure from the list and click on the Wizard button. 11
Summary of the content on the page No. 13
Step 3 If the Camera’s default IP address is on a different subnet, the following message will appear. Click Yes to continue. If you do not receive this message, skip to Step 6. Step 4 Enter admin for both the Admin ID and Password and click OK. 12
Summary of the content on the page No. 14
Step 5 The Wizard will automatically generate an IP address for the camera, if this address is not in use by any other device in your local network, click OK. Otherwise, enter an available IP address (ex. 192.168.x.240) and click OK. Step 6 Enter admin for both the Admin ID and Password field and click Next. Optionally, you can change the password by checking on the Change box and entering the new password. Step 7 If you need to change the Camera’s IP address because another net
Summary of the content on the page No. 15
Step 8 Verify that all the fields are correct and click Restart to save the settings and reboot the camera. Viewing Images Step 1 At the Setup Wizard, select the desired camera from the list and click on the Web Config button. 14
Summary of the content on the page No. 16
Step 2 Enter the username and password for the network camera. The default username and password are both “admin”. Step 3 The web based viewing page will appear. You can view live video by selecting either the ActiveX Mode (Internet Explorer only) or the Java Mode (Internet Explorer and Netscape). 15
Summary of the content on the page No. 17
Step 4 If you select ActiveX Mode, you may be prompt to install the ActiveX Control. Click on the yellow bar to on the top of the screen and click on Install ActiveX Control. Step 5 Click on Install. 16
Summary of the content on the page No. 18
Step 6 You can focus the camera by turning the camera’s lens clockwise or counter-clockwise. Note: ActiveX and/or Java Applet must be installed and enabled on your Web Browser (Internet Explorer or Netscape) before you can view the live videos. For more information please refer to the User’s Manual in the provided CD. Step 7 If you need to install Java Virtual Machine on your computer, do not follow the on-screen browser instructions for installing. Instead, go to http://www.jav
Summary of the content on the page No. 19
and "Admin Password" when you are the first time to use the SkyIPCam310. Once the ID and Password are defined, only the administrator has the access to management the SkyIPCam310. This procedure should be done as soon as possible since the security features with the SkyIPCam310 will not be enabled until the "Admin ID" and "Admin Password" is defined. 4 5 6 7 4. Application of the SkyIPCam310 The SkyIPCam310 can be applied in wide variety of applications. With the built-in CPU, it
Summary of the content on the page No. 20
Home Applications Diagram SOHO Internet Camera SOHO Wireless Internet Camera SOHO Applications Diagram SOHO 19
