Summary of the content on the page No. 1
OWNER'S MANUAL
61CM CORDLESS REMOTE COLOUR TELEVISION
MODEL: 6138
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA:1300 657 888
Summary of the content on the page No. 2
This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. DO read this handbook carefully and keep it handy for ready reference. ensure that all electrical connections (including the mains plug, extension leads and DO interconnections between pie
Summary of the content on the page No. 3
SOUND II INDICATOR STEREO INDICATOR SOUND I INDICATOR EXTERNAL SPEAKERS EX./IN SPEAKER SWITCH POWER SWITCH AUDIO OUTPUT POWER INDICATOR PUSH OPEN ANTENNA INPUT VIDEO OUTPUT STAND BY INDICATOR VIDEO INPUT INFRARED SENSOR AUDIO INPUT OPERATING INSTRUCTION: POWER ON/OFF SWITCH . Press the Power Switch, the appliance will be in "STANDBY" mode. A red light shows on the control panel. Press "PR-/+" buttons to turn on the set. The red light goes out, and a green light, shows on the control panel. . If
Summary of the content on the page No. 4
There are two ways to choose the channel number you want-the single-number method and the double-number method. 1.Single-digit Method (highest Program Number is 9) This allows numbers 0 ~ 9 ONLY and is useful for limiting the number of channels if you do not mind some channels on the wrong number (10 and 28 could be put on 1 and 0, for instance). Press the DIGITAL SELECT (-/--) button (12) on the remote control until the symbol "-" appears on the screen This is single digit mode. . The Keypad Nu
Summary of the content on the page No. 5
VHF-1 lllllllll------- When the set finds a TV signal, it will stop searching automatically, and show the TV picture on the screen. The tuning is optimised for strong signals. Weak signals may need fine tuning for the best result. If you want another channel, press the SEARCH button again. 3.The station may be fine-tuned with the FT (-/+) buttons for the best picture and sound if the auto-search result is not satisfactory. Another set of green bars appears in the upper right corner of the screen
Summary of the content on the page No. 6
STORE PP STORE - STORE PP Press STORE button Press PP button Press STORE button again The settings of picture and sound will be stored in memory until you reset them. TUNING & STORING A VCR The set is provided with Audio/Video sockets that allow direct connection to the VCR, but the set may also be used with the antenna connection. In this case, the VCR acts as a TV station. . Connect the VCR and play a tape. The antenna should be connected to the VCR, and the RF OUT from the VCR should be conn
Summary of the content on the page No. 7
THE CONTROL OF PICTURE AND SOUND 1.Function select . On the Front Panel, the "PICTURE" button is used to select the following functions: BRIGHTNESS, COLOUR, CONTRAST, BALANCE and VOLUME in that order. Each of the functions is adjusted by means of the adjacent -/+ level control buttons. The -/+ control buttons only work while the function is displayed. On the Remote Control Unit, each function has a separate set of buttons. 2.Adjustments ON SCREEN ---------------- DISPLAY Decrease Green Bar Moves
Summary of the content on the page No. 8
REMOTE CONTROL UNIT The remote control unit allows almost everything to be adjusted from the armchair. DIGITAL BUTTON 16 14 TV 13 AV 12 DIGITAL SELECT 11 SOUND MPX SWITCHING RECALL 15 VOLUME UP/DOWN 5 10 SLEEP 3 CONTRAST UP/DOWN PR (+/-) 6,7 1 STANDBY PP 8 MUTE 9 4 COLOUR UP/DOWN BRIGHTNESS UP/DOWN 2 17 BALANCE LEFT/RIGHT BATTERIES: 1. Remove the battery cover of Remote Control Unit. 2. Insert two "AA" 1.5V batteries making sure the polarity ( + / - ) of the batteries matches the polarity mar
Summary of the content on the page No. 9
BUTTON LIST The trick is to push the buttons slowly; it takes a moment to register. Be careful that the button does not lock down. Some buttons behave differently in TV and Teletext. The following list is grouped according to TV or Teletext. If the description of a button is missing in one list, it will be found in the other. . TV FUNCTIONS 1. STANDBY (O) This turns the set off. The red STANDBY light comes on to show that the set is in Standby. If the set is left unattended for long periods it
Summary of the content on the page No. 10
16. DIGITAL BUTTON In single-digit mode, press these buttons to select any of 0~9 channels. In double-digit mode, press these buttons to select any of 00~39 channels. 17. BALANCE LEFT/RIGHT Press these two buttons to balance the Sound between left and right. The left button reduces the volume of the right speaker: the right button reduces the volume of the left speaker. LISTENING TO STEREO/DUAL-CHANNEL TV SOUND The Model 6138 is fitted with full performance Stereo Theatre Sound where the interna
Summary of the content on the page No. 11
. SOUND MULTIPLEX SWITCHING The TV station has the option of transmitting Mono, Stereo, or Dual-channel sound. The set detects the transmission automatically and allows the S. MPX button to make the correct choices. . S. MPX Button (11) The choice of sound is limited by what the TV station is sending. The possible choices are shown below. Press the button and the choices available will be displayed on the screen in turn. DUAL I DUAL II STEREO MONO Dual Sound Transmission Mode Stereo Sound Trans
Summary of the content on the page No. 12
. OUT Sockets These sockets take the signal OUT of the TV set and feed it TN to the VCR. They are hardly ever used. Most VCR’s have their own Tuner built in and do not need the TV set to tune the TV channel for them. The usual setup is to give the VCR the antenna, and feed the TV set out of the VCR’s RF output. (This loops the antenna signal through and shares it). See your VCR manual. The exception to this is if you are dubbing one VCR off another. The connection for this is shown later. . IN S
Summary of the content on the page No. 13
CONNECTION DIAGRAMS 1. VIDEO PLAYBACK/RECORD This is the usual connection where Audio/Video is taken out of the VCR and is connected IN to the TV set. . The material being played on the VCR can be viewed on the TV screen by pressing the AV Button (13). . Pressing the TV Button (14) shows the TV station being tuned by the TV set. . If the VCR is recording (using its own tuner), you can watch what the VCR is recording by pressing the AV button (13), or what the TV set is getting off-air, by press
Summary of the content on the page No. 14
3. DUBBING The figure below shows how to connect TWO VCRs to the TV for dubbing one from the other. Press AV Button (13) to switch to Video mode. The TV set will act as a monitor to help edit while dubbing. The set MUST remain in Video mode and MUST NOT be switched off during the session. 13
Summary of the content on the page No. 15
CONNECTING EXTERNAL SPEAKERS You can connect speakers to the EXTERNAL SPEAKER terminals on the TV set to enhance sound from the TV. Note: Before connecting the external speakers, turn off your TV set. 1 Connect speaker leads While pressing the button, insert the wire into the hole as shown below, and then release the button. Pull firmly on the sire make sure it is secure. Note: Be Sure to connect the Right speaker to the R + and - and the Left speaker to the L + and - 2 Set the SPEAKER SELECT
Summary of the content on the page No. 16
TROUBLE SHOOTING Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other similar causes. If any difficulty arises in the operation of your set, first check through this list of symptoms and correction. Should the difficulty cause concern, unplug the set and contact your dealer. Symptoms Check these things Try these adjustment . . Press POWER BUTTON Be sure power cord is plugged in. . No picture, . . Try another channel. May be station trouble. no sound.
Summary of the content on the page No. 17
Specifications : CCIR PAL, B/G; NTSC PLAYBACK Colour System: : VHFL 0-3; VHFH 4-11; UHF 21-69 Receivers Channel : S1-S41 (OPTION) Cable Channel : FULL REAL STEREO Stereo : AC 120-240V, 60/50Hz Power supply : 61cm Flat Square Picture Tube CRT : 2 x 7W Max : 2 x 5W 10% THD Audio Output : VHF/CATV/UHF 75 ohm Antenna Impedance : 640 (W) x 563 (H) x 460 (D) Dimension (mm) : 32kg Weight Remote Control Unit : DC 3V (2 x UM-3) Power Supply * Design and specifications are subject to change without notice
Summary of the content on the page No. 18
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-64063-01
