Summary of the content on the page No. 1
OWNER'S MANUAL
61CM CORDLESS REMOTE COLOUR TELEVISION
MODEL: 6125TS
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4164
Standards Australia
APP No: N15959
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Summary of the content on the page No. 2
Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. Screen displays and illustrations in this manual may differ from the actual ones for better visibility.
Summary of the content on the page No. 3
Contents Features ........................................................................................................................ 1 Important Safety Cautions .......................................................................................... 2 Identification of Controls ............................................................................................ 4 Front view ...........................................................................................................
Summary of the content on the page No. 4
Features 2 USOC and Intellectualized I C-bus control Five picture modes Two groups of Video/Audio input terminal One S-VIDEO termial One group of DVD (Y, Cr, Cb) input terminals Audio/Video output terminals Program exchange/Program copy Game/Calendar Child lock function 200 channels Music TV function Noise reduction Image enhancing Channel scanning Programs classified Screen protecting function 1
Summary of the content on the page No. 5
Important Safety Cautions When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Do not expose the TV set to rain or excessive moisture. Avoid using the set in very warm or damp places and never use it in a bathroom. When cleaning dust off the picture tube disconnect the power first. You can wipe lightly with a piece of dry, clean and soft cloth. Avoid exposing the set to direct sun
Summary of the content on the page No. 6
Important Safety Cautions When any unusual situation occurs, turn off the power supply at once and remove the plug from the wall outlet. Contact a qualified service department in your local area. Do not expose the TV set to rain or excessive moisture. Avoid using the set in very warm or damp places and never use it in a bathroom. When cleaning dust off the picture tube disconnect the power first. You can wipe lightly with a piece of dry, clean and soft cloth. Avoid exposing the set to direct sun
Summary of the content on the page No. 7
This TV set can operate on a power of ~240V, 50Hz. You must not use a power supply of any other type. Do not cover the ventilating hole in the cabinet Keep a space of more than 10cm from the walls to the TV set to ensure adequate ventilation. If the power cord or the plug is damaged contact a qualified service department for service. When the TV set is to be left unattended for a long period of time, turn off the power supply and remove the plug from the wall outlet. Don't try to push anything i
Summary of the content on the page No. 8
Identification of Controls Front view 1 2 3 AV/TV MENU VOL- VOL+ CH- CH+ 4 5 6 7 8 9 1. Power Switch. 2. Remote Sensor. 3. Indicator. 4. AV/TV button: Video input select. 5. MENU button: To enter into menu operation. 6. VOL- button: volume down adjust; menu item adjust. 7. VOL+ button: volume up adjust; menu item adjust. 8. CH- button: channel down select; menu item select. 9. CH+ button: channel select; menu item select. 4
Summary of the content on the page No. 9
Back view (2) R L/MONO VIDEO 6 (1) DVD VIDEO Y VIDEO 1 L CB L S-VIDEO AUDIO AUDIO R CR R 5 4 3 2 1. Antenna input 2. AV Output (VIDEO, AUDIO L, R) 3. AV1 input (VIDEO, AUDIO L, R) 4. AV output (VIDEO, AUDIO L, R) 5. S-VIDEO input 6. AV2 input (VIDEO, AUDIO L, R) 5
Summary of the content on the page No. 10
Identification of Controls (continued) Remote control Power on/standby Sound Mute 1 2 3 Direct Channel select 4 5 6 PRESET To display PRESET menu 7 8 9 SLEEP Sleep timer AV 0 Previous channel TV/VIDEO Input select Channel up/menu item select To access MENU operation PIC CH DSP On-screen display call To display the PICTURE menu MENU Volume up/menu item adjust VOL VOL Volume down/menu item adjust Picture mode select This button has no CH function on this model S-MODE PP Channel down/menu item sele
Summary of the content on the page No. 11
30 30 Battery Installation Please install the batteries before using the remote control. Open the battery cover. Install two "AA" batteries Replace the battery cover. 2 1 3 matching the +/- polarities of the battery to the +/- marks inside the battery compartment. Effective range of the remote control Notes: 1. There should be no obstacle between the TV and the transmitter. 2. Use the remote control within the effective range as the above figure. 3. If the remote control does not work,
Summary of the content on the page No. 12
Installation Connecting antenna Optimum reception of colour requires a good signal and will generally mean that an outdoor antenna must be used. The exact type and position of the antenna will depend upon your particular area. Notes: Turn off the power first, when you connect an outdoor antenna to the antenna input terminal. When installing an outside antenna system, extreme care should be taken to keep from touching power lines or circuits as contact with them might be fatal. In thunder and li
Summary of the content on the page No. 13
Connecting video and audio equipment This TV set provides 2 groups of AV input terminals (including 1 group of DVD and S-Video input terminals) for your convenient connection to VCR, DVD or other video equipment to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Connecting the rear AV input terminals. Video equipment To audio without S-video outputs terminal To video To Y output output To Cr output To Audio R output Y Yellow (video) To
Summary of the content on the page No. 14
Connecting the side AV input terminals (2) R VIDEO EQUIPMENT L/MONO VIDEO To video output To audio outputs Y W R Signal Connecting the AV output terminals (1) DVD VCR VIDEO Y VIDEO L CB L S-VIDEO AUDIO AUDIO R CR R Audio Amplifier 10 R W Y Y
Summary of the content on the page No. 15
Operations Menu Introduction Press the MENU button repeatedly to select the screen display as below. In menu operation, press CH+/- to select item, press VOL+/- to adjust selected item. The SYSTEM1 menu The PICTURE menu BRIGHTNESS 50 COLOR SYS AUTO CONTRAST 50 SOUND SYS BG COLOR 50 BACKGROUND ON SHARPNESS 50 PROGRAM 007 TINT 50 EXCHANGE --- COPY --- SEL ADJ SEL ADJ The SYSTEM2 menu The PRESET menu (TV mode only) PROGRAM 008 IMAGE ENHANCE ON TYPE USER2 NR ON BAND V-H SKIP OFF CALENDAR FINE TUNE G
Summary of the content on the page No. 16
Operations Turning On/Turning Off Turning On 1 Press the MAIN POWER SWITCH to turn on the TV set. 2 If the TV set is in STANDBY mode. Press , CH+/- or 0-9 buttons (one digit only) on the remote control, then the TV set is turned on. When the remote control is not at your hand, you can also press the CH+/- buttons on the TV set to turn on the TV. Note: If there is no input signal to the TV when the TV is on, blue background will appear on the screen (when the BACKGROUND is set to ON). After
Summary of the content on the page No. 17
Operations Presetting programs Firstly, use the Auto search function to preset all active channels in your area automatically. Then arrange the preset channels with the manual search and program edit functions. Auto Search Press the MENU button to select PRESET menu. Press CH+/- to select AUTO SEARCH. PROGRAM 008 TYPE USER2 Press VOL+/- and the TV set starts Auto channel preset. All BAND V-H SKIP OFF FINE TUNE active channels will be preset and stored into the memory MANUAL SEARCH AUTO SEARCH au
Summary of the content on the page No. 18
Operations Presetting programs (continued) Fine Tuning When picture and sound's effect of a channel is poor (for example: one or two CATV channel's picture and sound are not standard), you can correct them by making use of PROGRAM 008 TYPE USER2 BAND V-H Fine tuning. SKIP OFF FINE TUNE MANUAL SEARCH AUTO SEARCH Access the PRESET menu, then select PROGRAM item by SEL ADJ CH+/- and set the desired channel number (from 0~199) by VOL+/- or Digit buttons. In the menu, select FINE TUNE item, then pres
Summary of the content on the page No. 19
Operations Editing programs Channel skipping After presetting the channels, you can skip unnecessary position numbers so that only the channels you want are selected. PROGRAM 008 TYPE USER2 Access the PRESET menu, then select PROGRAM item by BAND V-H SKIP OFF FINE TUNE CH+/- and set the desired channel number (from 0~199) by MANUAL SEARCH AUTO SEARCH VOL+/- or Digit buttons. SEL ADJ In the menu, please select SKIP item and press VOL+/- buttons to select ON. Now the selected channel will be skipp
Summary of the content on the page No. 20
Operations Editing programs (continued) Channel exchange/copy After channel presetting, you can edit the programs by using the channel exchange and channel copy functions. COLOUR SYS AUTO SOUND SYS BG Press MENU button repeatedly to access the SYSTEM1 menu. BACKGROUND ON PROGRAM 007 Select PROGRAM item and select a channel number A EXCHANGE --- COPY --- by Digit buttons. SEL ADJ Select EXCHANGE item and press Digit buttons to set COLOUR SYS AUTO another channel number B that you would like to ex
