Summary of the content on the page No. 1
User’s manual
w w w.v te c h p h o n e s .c o m
Model:
LS6375-3
(LS6325-2 and IS6100)
Summary of the content on the page No. 2
Congratulations on purchasing your new VTech product. Before using this telephone, please read Important safety instructions on page 75 of this manual. This manual has all the feature operations and troubleshooting necessary to install and operate your new VTech telephone. Please review this manual thoroughly to ensure proper installation and operation of this innovative and feature rich VTech product. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.
Summary of the content on the page No. 3
Table of contents Getting started ...............................1 Call waiting ....................................26 Equalizer........................................26 Parts checklist .................................1 Chain dialing ..................................27 Telephone base and handset Redial list .......................................28 charger installation .......................2 Installation options ...........................3 Dial a redial entry...........................28
Summary of the content on the page No. 4
Table of contents Answering system settings ........ 47 Maintenance ..................................76 About cordless telephones ............ 77 Answering system setup................ 47 ® The RBRC seal ............................77 Answer ON/OFF ............................47 Warranty ........................................78 Call screening ................................48 FCC, ACTA and IC regulations ..... 80 Number of rings .............................48 Technical specifications.......
Summary of the content on the page No. 5
Getting started Parts checklist Your telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Handset charger and Cordless Cordless Headset charger handsets (2) headset power adapter charger adapter Head band Additional Additional Headset ear hooks (2) charger earbuds (3) Telephone base Wall mount bracket Handset Handset battery compartment batteries (2) covers (2) Telephone base Quick start guide Telephone Use
Summary of the content on the page No. 6
Getting started Telephone base and handset charger installation Install the telephone base and handset charger as shown below. Make sure that the electrical outlet is not controlled by a wall switch. If you subscribe to digital subscriber line (DSL) high-speed Internet service through your telephone line, you must install a DSL filter between the telephone line cord and the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Contact your DSL servi
Summary of the content on the page No. 7
Getting started Installation options Your telephone base is ready for tabletop use. If you want to mount your telephone on a wall, use the provided wall mount bracket to connect with a standard dual-stud telephone wall mounting plate. If you do not have this mounting plate, you can purchase one from many hardware or consumer electronics retailers. You may need a professional to install the mounting plate. Tabletop to wall mount installation 1. Plug one end of the telephone line cord into the
Summary of the content on the page No. 8
Getting started Wall mount to tabletop installation 1. If the telephone line cord and power adapter cord are bundled, untie them first. 2. Slide the wall mount bracket up and remove it from the wall plate. Unplug the telephone line cord (or DSL filter) from the wall. Unplug the power adapter from the power outlet. 3. Slide the telephone base up and remove it from the wall mount bracket. 4. See Telephone base and handset charger installation on page 2. 3 1 2 4
Summary of the content on the page No. 9
Getting started handset battery installation Install the battery as shown below. 1. If the battery compartment cover is on the handset, press on the grooved tab and slide the cover to remove. 2. Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label. 3. Place the handset battery with the label ThIS SIDE UP facing up and the wires inside the battery compartment. 4. Align the cover flat against the battery compartment, then sli
Summary of the content on the page No. 10
Getting started handset battery charging Once you have installed the handset battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The handset battery is fully charged after 16 hours of continuous charging. See the table on page 61 for battery operating times. If the screen is blank or displays Plac
Summary of the content on the page No. 11
Getting started headset charger installation Install the headset charger as shown below. Plug the large end of the headset charger power adapter into an electrical Plug the small end of outlet not controlled by a the headset charger wall switch. power adapter into the power jack of the headset charger. Headset charger Power on the headset Power on the headset before use. Place the headset in the headset charger or press and hold for two seconds. The light flashes three times in blue
Summary of the content on the page No. 12
Getting started headset attachments Earbud There are four earbuds provided and one of them has been attached to the headset. To remove the earbud from the headset earpiece: Hold both sides of the earbud and then pull the earbud until it separates from the earpiece. To attach the earbud to the headset earpiece: 1. Choose an appropriate earbud. 2. Press the earbud towards the earpiece until it clicks into place. Move the earbud around so that the protruding bump on the earbud is pointing tow
Summary of the content on the page No. 13
Getting started headset attachments (continued) Ear hook There are three ear hooks provided and one of them has been attached to the headset. To adjust the headset to wear on your right ear: o 1. Hold the headset with one hand. 2. Twist the ear hook 180 clockwise. Lift the ear hook upward. 3. Push the ear hook downward. 4. Hook the headset on your right ear. Adjust the angle of the headset until the microphone is pointing towards your mouth. 9
Summary of the content on the page No. 14
Getting started headset attachments (continued) To remove the ear hook from the headset: 1. Hold the headset with one hand and the ear hook with your other hand. 2. Pull the end of the ear hook up until it separates from the rotating clip on the headset. 10
Summary of the content on the page No. 15
Getting started headset attachments (continued) To attach the ear hook to the headset: 1. Remove any headset attachment (earbud excluded) connected to the headset. 2. Choose an appropriate ear hook. 3. Insert the ear hook [A] into the rotating clip [B] on the headset until it clicks into place. [A] [B] 4. Hook the headset on your right ear. Adjust the angle of the headset until the microphone is pointing towards your mouth. Firmly grip the earpiece with one hand whenever adjusting the head
Summary of the content on the page No. 16
Getting started headset attachments (continued) head band To attach the head band to the headset: 1. Remove any headset attachment (earbud excluded) currently connected to the headset. 2. To wear the headset on your right ear, insert the end [A] of the head band into the rotating clip [B] on the headset until it clicks into place. [A] [B] 3. Adjust the head band to fit your head. Adjust and rotate the angle of the headset until the microphone is pointing towards your mouth. Firmly grip
Summary of the content on the page No. 17
Getting started headset attachments (continued) headset attachments (continued) To remove the head band from the headset: head band 1. Hold the headset with one hand and the head band with your other hand. To attach the head band to the headset: 2. Pull the end of the head band until it separates from the rotating clip on the headset. 13
Summary of the content on the page No. 18
Getting started handset layout ChARGE light On when the handset is charging in the telephone base or charger (page 5). / VOL (directory/volume) Press to enter the directory when the telephone is not in use (page 40). While in a menu, press to scroll up. During a call, press to increase the listening volume (page 24). (speakerphone) Press to make or answer a call (page 24). Press to join a call (page 28). During a call, press to switch between the speakerphone and handset (page 24). /FLASh P
Summary of the content on the page No. 19
Getting started handset layout VOL/CID (volume/caller ID) Press to review the call log when the telephone is not in use (page 44). While in a menu, press to scroll down. During a call, press to decrease the listening volume (page 24). MENU/SELECT Press to show the menu. While in a menu, press to choose an item, or save an entry or setting. OFF/CLEAR During a call, press to hang up (page 24). While the handset is ringing, press to silence the ringer temporarily (page 25). While the telephone
Summary of the content on the page No. 20
Getting started handset layout PUSh TO TALK (PTT) Press to begin a one-to-one or one-to-all broadcast message (page 32). 16
