Summary of the content on the page No. 1
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 37
CORDLESS TELEPHONE WITH CALLER ID
MODEL: MPH2410
BEFORE OPERATING THIS PRODUCT,
PLEASE READ THESE INSTRUCTIONS COMPLETELY.
OPERATING INSTRUCTIONS
Summary of the content on the page No. 2
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 1 IMPORTANT SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION The Owner’s Manual contains important operating and maintenance instructions. For your safety, it is necessary to refer to the manual. Warning: Changes or modifications to this unit not expressly approved by the party
Summary of the content on the page No. 3
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 2 IMPORTANT SAFETY PRECAUTIONS (CONTINUED) When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this product. 3. Do not use this product near water- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or ne
Summary of the content on the page No. 4
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 3 IMPORTANT SAFETY PRECAUTIONS (CONTINUED) 1. If your local telephone exchange only accepts Pulse dialing, you may have to switch the Tone/Pulse switch to Tone to access certain services that require Tone signalling (such as home banking). After the initial line is connected to the number you are calling, switch the Tone/Pulse switch to Tone to access Tone signalling. When you have completed your call, please switch the Tone/Pulse switch back to Pulse. 2. H
Summary of the content on the page No. 5
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 4 CONTENTS Important Safety Precautions ........................1 Viewing the Phonebook...........................29 Contents ........................................................4 Saving Caller ID Information to Location of Controls and Indicators ...............5 the Phonebook ........................................30 Installation Instructions ..................................6 Dialing a Number from the Phonebook ...30 Wall Mounting the Unit (Standa
Summary of the content on the page No. 6
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 5 LOCATION OF CONTROLS AND INDICATORS HANDSET BASE 1 17 18 19 2 23 11 3 20 4 12 21 5 22 6 13 14 7 8 9 15 10 16 1. Handset Antenna 15. Option/# Button 2. NEW CALL/MSG WTG Indicator 16. DEL (Delete)/CHAN (Channel) 3. Display Button 4. TALK Button 17. TONE/PULSE Switch (Rear of 5. Scroll Up/Down/Left/Right Buttons Base) 6. VOICE MAIL/MENU Button 18. DC 9V Jack (Rear of Base) 7. Key Buttons (0-9) 19. Telephone LINE Jack (Rear of 8. HEADSET Jack (Side of Handset
Summary of the content on the page No. 7
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 6 INSTALLATION INSTRUCTIONS 1. Carefully unpack and remove your unit from the box. 2. Make sure all of the following items have been included: • Base Unit (AC120V, 60Hz/DC9V, 300mA) • Handset Unit •2 Telephone Cords (Short and Long) • Rechargeable Ni-Cd Battery Pack • Belt Clip (3.6V, 600mAH) • Mounting Bracket with Screws • AC Adapter 3. Make sure the Rechargeable Battery is installed or install the Rechargeable Battery as described on page 9. PLEASE REFE
Summary of the content on the page No. 8
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 7 INSTALLATION INSTRUCTIONS (CONTINUED) WALL MOUNTING THE UNIT (STANDARD WALL JACK) Follow the instructions below to install the base onto a standard telephone wall jack: 1. Connect the short telephone line cord to the TEL LINE jack on the rear of the base unit. 2. Insert the free end of the short line cord through the hole of the mounting bracket. 3. Insert the hooks of the mounting bracket into the matching slots on the back of the unit as shown in Figur
Summary of the content on the page No. 9
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 8 INSTALLATION INSTRUCTIONS (CONTINUED) WALL MOUNTING THE UNIT (NO STANDARD WALL JACK) 1. Drill two holes with a vertical distance between the two marked positions of 3 15/16" (100mm). 2. Drive a screw into each of the holes. Tighten them to the end of the screw lines, only leaving the smooth part of the screw head outside the wall. 3. Install the wall mount bracket into the base unit as previously discussed in Figures 3-6 on the previous page. Screws 4. H
Summary of the content on the page No. 10
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 9 INSTALLATION INSTRUCTIONS (CONTINUED) INSTALLATION OF THE RECHARGEABLE BATTERY 1 2 Remove the battery cover located on Connect the Ni-Cd battery pack plug the rear of the handset by pressing on into the battery connector; the LCD the top cover and sliding it downward. display will turn on in the Standby mode. Insert the Ni-Cd battery pack into the battery compartment. 3 Put the b
Summary of the content on the page No. 11
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 10 SET-UP INSTRUCTIONS SETTING THE RINGER VOLUME Set the ringer volume (HI, LOW, OFF) while in the Standby mode as follows: 1 2 Press and hold the VOICE MAIL/ Press the EDIT/FLASH button to MENU button for more than two change the setting; the Ringer Volume seconds; the Ringer Volume setting setting will blink. will appear in the display. 3 4 1 2 Press the Scroll Up ❶ or Down ❷ When the desired Ringer Volume setting appears, press and hold the button to sel
Summary of the content on the page No. 12
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 11 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE LANGUAGE Set the language (ENGLISH, SPANISH, FRENCH) while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ once MENU button for more than two or the 2 key button ❷ once; the seconds; the Ringer Volume setting Language setting will appear. will appear in the display. 3 4 1 2 Press the EDIT/FLASH button to Press the Scroll Up ❶ or Down ❷ change the setting; th
Summary of the content on the page No. 13
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 12 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE FIRST RING This feature will turn the first ring of the phone On or Off. Set to Off so the phone does not ring until the Caller ID information has been displayed. Turn the first ring option On or Off while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ twice MENU button for more than two or the 3 key button ❷ ; the First Ring seconds; the Ringer Volume sett
Summary of the content on the page No. 14
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 13 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE TIME AND DATE Change the Time and Date while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ three MENU button for more than two times or the 4 key button ❷ ; the Time seconds; the Ringer Volume setting Setting will appear. will appear in the display. 3 4 Press the EDIT/FLASH button to Set the month using the Key buttons change the setting; the month setting
Summary of the content on the page No. 15
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 14 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE LCD CONTRAST If you find the LCD screen difficult to read, set the contrast level while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ four MENU button for more than two times or the 5 key button ❷ ; the seconds; the Ringer Volume setting Contrast setting will appear. will appear in the display. 3 4 1 2 Press the EDIT/FLASH button to Press the Scroll Up ❶ o
Summary of the content on the page No. 16
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 15 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE PBX NUMBER This feature will insert a number (0-9) before the outgoing number, if required. When a number is selected, the unit will automatically dial the preset PBX number and a pause before any speed dial or Caller ID callback. Set the PBX number while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ five MENU button for more than two times or the 6 key bu
Summary of the content on the page No. 17
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 16 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE FLASH TIME This unit enables you to select the standard flash time applicable to your calling area, which is useful when “clicking” over to a call waiting call or for PBX systems. If you are not sure of the flash time, call your local telephone company. Set the Flash Time while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ six MENU button for more than two
Summary of the content on the page No. 18
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 17 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE PAUSE TIME This unit enables you to change the number of seconds that a pause lasts when using programmed pauses in your speed dial numbers or after your PBX number. Set the Pause Time while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ seven MENU button for more than two times or the 8 key button ❷ ; the Pause seconds; the Ringer Volume setting Time setti
Summary of the content on the page No. 19
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 18 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE VOICE MAIL This unit enables you to store the Voice Mail Post Code number in your area. This will automatically connect you to the Voice mail server provider with one touch dialing. Set the Voice Mail setting while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ Press the Scroll Down button ❶ eight MENU button for more than two times or the 9 key button ❷ ; the Voice seconds; the Ringer V
Summary of the content on the page No. 20
MPH2410.O/M.QXD 3/7/03 9:35 AM Page 19 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE MESSAGE WAITING The unit’s Message Waiting setting is set to OFF by default. Message Waiting will turn on automatically only when your local phone company sends the signal provided that this optional service is available in your area. When all messages have been received, the local telephone company will send a signal to turn the Message Waiting off. In the unlikely event the Message Waiting On signal fails to
