Summary of the content on the page No. 1
USER’S MANUAL
Part 2
DRAFT 7/10/01
900 MHz Cordless Telephone 6200
Please also read
Part 1 — Important
Product Information
AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones.
Net2Phone is a registered trademark of Net2Phone, Inc.
© 2001 Advanced American Telephones. All rights reserved. Printed in China. Issue 1AT&T 7/01
Summary of the content on the page No. 2
INSTALLATION Before You Install 2 Install the handset battery following 1 Choose a location for the base near an electrical Figure A below. outlet and a telephone jack. 3 Attach the belt clip to the cordless handset This phone requires a modular telephone jack and a as in Figure B below (optional). standard electrical outlet (110v AC) not controlled by a wall switch. a) Remove battery b) Align two holes in compartment plug with socket cover by pressing pins, and snap the on the plug into plac
Summary of the content on the page No. 3
INSTALLATION Wall Installation 1 Position the wall mount adapter on the base. 2 Connect the telephone line cord. 3 Connect the power cord. 4 Mount the base on the wall. 5 Follow Steps 3 and 4 in Align tabs on wall Table/Desk Installation. mount adapter with holes on bottom of base. Snap wall mount adapter firmly into place. a) Align holes on base with mounting studs on wall jack. Mounting Studs b) Place power cord as shown, so it hangs straight down between base and wall. c) Pull base down on
Summary of the content on the page No. 4
TELEPHONE OPERATION On steadily when handset is in base Page/Handset Handset Volume Locator Adjust volume of what you hear Press once to page through the handset. the handset for up to one minute — OR — Press twice to cancel. Flash/Call Waiting Access special telephone company subscriber services. Make or Answer Net2Phone a Call Access your Net2Phone Lift handset account for internet calling. from base — OR — Press P and wait for light to Redial go on steadily. Follow the instruction
Summary of the content on the page No. 5
TELEPHONE OPERATION Making a Net2Phone Call Handset Ringer Style You can select from four different handset ringer styles. • Press P, on the cordless handset to access your Net2Phone account. Follow the voice 1 Make sure the handset is off. prompts to complete your call. 2 Press g,#. 3 Press 1,2,3 or 4 to select your ringer style. Changing your Net2Phone Access Number You will hear a sample of the ringer style. This phone is pre-programmed to dial 1 866 333-8506 4 Press g. when you press . If Ne
Summary of the content on the page No. 6
TELEPHONE MEMORY This cordless phone can store nine telephone numbers, each up to 16 digits long. Store Memory Numbers 1 Make sure the handset is off. 2 Press g. The PHONE light blinks. 3 Dial the telephone number (up to 16 digits) — OR — Press R to store the last number dialed. 4 Press g. 5 Press the number button (1–9) where you want to store the telephone number. Change/Replace a Stored Memory Number Store a new number in its place. Store a Pause in a Memory Number Press to store a two-secon
Summary of the content on the page No. 7
BATTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack This battery should remain charged up to six days with 1 Remove the battery compartment cover on the the ringer turned on and up to 12 days with the ringer handset by pressing on the indentation and sliding off. A fully charged battery provides an average talk time the cover downward. of about six hours. 2 Lift out the old battery pack and disconnect. The battery pack needs charging when: 3 Align the two holes in the
Summary of the content on the page No. 8
IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the sugges- If you hear noise or interference when using the phone: tions below. For Customer Service, visit our website at • Make sure the base antenna is fully upright. www.telephones.att.com or call 1 800 222–3111. • You may be out of range. Move closer to the base. Please retain your receipt as your proof of purchase. • Press and release C to change to another of the 30 channels available. If noise is exceptionally loud,
