Summary of the content on the page No. 1
Table of contents
1. Precautions for safety and use_________________________ 4
2. Fitting the appliance in the top _________________________ 5
2.1 Fixing to the supporting structure ________________________________________5
3. Electrical connection ________________________________ 7
3.1 Clearance above and around domestic appliances __________________________8
3.2 Room ventilation_____________________________________________________9
3.3 Discharge of combustion products ______________
Summary of the content on the page No. 2
Precautions for Safety and Use 1. Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND
Summary of the content on the page No. 3
Instructions for the Installer 2. Fitting the appliance in the top The procedures required below must be carried out by a skilled builder and/or joiner. The hob can be installed on various materials, including masonry, metal, solid wood and wood finished with plastic laminates, provided the material is heat-resistant (T 90° C). 2.1 Fixing to the supporting structure Make a hole in the cabinet top with the dimensions shown here, maintaining a distance of at least 70 mm fro
Summary of the content on the page No. 4
Instructions for the Installer edge of the gasket B. The dimensions in the drawing below refer to the hole on the inside edge of the gasket. In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the unit and the panel surface. The panel has to be easily removable to allow access in the event of technical service. See right for the precise holes to be u
Summary of the content on the page No. 5
Instructions for the Installer 3. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed. Pass the power supply cable through the rear of the cabinet, taking care that
Summary of the content on the page No. 6
Instructions for the Installer 3.1 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm. Any other downward facing combustible s
Summary of the content on the page No. 7
Instructions for the Installer 2 Side clearances – (Measurements B & C) Where B, measured from the periphery of the nearest burner to any vertical combustible surface, is less than 200 mm, the surface shall be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width or depth) of the cooking surface area. Where the cooking appliance is fitted with a ‘splashback’, protection of the rear wall is not required. 3 Additio
Summary of the content on the page No. 8
Instructions for the Installer 4. GAS CONNECTION This appliance is suitable for installation with Natural Gas or LPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet. A test point (for checking the gas pressure) is supplied either with the regulator or as a separate fitting in the case of LPG (propane) appliances.
Summary of the content on the page No. 9
Instructions for the Installer 5. Adapting to different types of gas Before carrying out the operations described below, disconnect the appliance from the electricity supply. The hob of the cooker is adjusted for use with either natural gas at a pressure of 1.0 kPa. If used with other types of gas, you have to replace the nozzles, then adjust the minimum flame on the gas taps. For nozzle replacement and burner adjustment operate as described in the following paragraph. 5.1 Re
Summary of the content on the page No. 10
Instructions for the Installer 5.2 Adjusting for bottled gas Undo the screw A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm. Return the support B to its original position, so that the nozzle C is perfectly covered. Regulate the air flow by moving the Venturi pipe D until the distance “X” state
Summary of the content on the page No. 11
Instructions for the Installer 5.4 Adjusting the primary air flow Refers to the gap “X” in mm. BURNER NG – 1.0 kPa ULPG – 2.75kPa Auxiliary 4.0 10.0 Semi rapid 4.0 10.0 Rapid (3) 4.0 10.0 Rapid (6) 4.0 10.0 Rapid (7) 4.0 10.0 WOK double flame Internal 5.0 8.0 (4-8) External 10.0 13.0 WOK 5.0 12.0 5.5 Reassembling the hob skin Reverse the procedure described in point “5.1 Removing the hob skin ”. When replacing the burner rings, bear in mind that they must
Summary of the content on the page No. 12
Instructions for the Installer 5.8 Hob burner layout Burner type 1 Auxiliary 2 Semi rapid 3 Rapid 4 WOK Double flame 5 WOK 6 Rapid 7 Rapid 8 WOK Double flame 5.9 Greasing the gas taps Over time, the gas taps may become stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician. 14
Summary of the content on the page No. 13
Instructions for the User 6. Description of controls 6.1 The front panel All the hob's control and monitoring devices are placed together on the front panel. MODEL 60 CONTROL PANEL 4 Burner Hob MODEL 70 CONTROL PANEL 5 Burner Hob 6 Burner Hob, UR2 at Side 6 Burner Hob, central UR2 KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between
Summary of the content on the page No. 14
Instructions for the User 7. Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. 7.1 Lighting burners with safety device The burner it controls is shown next to each knob (the example here shows the front left-hand burner).
Summary of the content on the page No. 15
Instructions for the User 7.4 Pan diameters BURNERS min. and max. Ø (in cm) 1. Auxiliary 7-18 2. Semi rapid 10-24 3. Rapid 18-24 4. WOK double flame 20-28 5. WOK 20-28 6. Rapid 18-24 7. Rapid 18-24 8. WOK double flame 20-28 17
Summary of the content on the page No. 16
Instructions for the User 8. Cleaning and maintenance Before carrying out any operations, disconnect the appliance from the electricity supply. 8.1 Cleaning stainless steel To keep the hob in good condition, it must be cleaned regularly, after each use, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning and caring for stainless steel surfaces, always use only specific products which do not contain abrasives or chlorine-based acids. Instructions fo
