Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS
HB0037
MODEL E662
! INTENDED FOR DOMESTIC COOKING ONLY !
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 AND 13.
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)
Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626)
REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register
V06800 rev. F
Summary of the content on the page No. 2
! WARNING ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC TO REDUCE THE RISK OF INJURY TO PERSONS SHOCK OR INJURY TO PERSONS, OBSERVE IN THE EVENT OF A RANGE TOP GREASE THE FOLLOWING: FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the 1. SMOTHER FLAMES with a close-fitting lid, manufacturer. If you have questions, contact the cookie sheet or metal tray, then turn off the manufacturer at the address or telephone number burner. BE CAREFUL TO PREVENT BURNS. IF listed
Summary of the content on the page No. 3
TABLE OF CONTENTS BROAN ELITE E662 HOOD SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1. INSTALL DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2. PREPARE THE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 3. CABINET PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
BROAN ELITE E662 HOOD SYSTEM Model 634 or 644 Model 647 Model 634 or 644 Model 643 (roof cap) (7” Rd wall cap) (roof cap) (8” Rd wall cap) Model 412 8” round Model 415 transition adjustable 7” Model 459 (3¼” x 10” elbow adjustable transition to 7” round) (optional) elbow (3¼” x 14” to 8” round) (optional) Model 407 8” Round 7” Round 3¼” x 14” standard rectangular standard duct standard duct duct Model 459 3¼” x 10” transition rectangular (3¼” x 14” standard to 8” round) Model T460 duct transi
Summary of the content on the page No. 5
1. INSTALL DUCTWORK Plan where and how the ductwork will be installed. Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use 2” duct tape to seal duct joints. NOTE: When performing vertical exhaust ductwork, there must be at least 14” high free inside cabinet in order to allow cabinet blower installation. The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above cooktop is highly recommended for best capture of
Summary of the content on the page No. 6
3. CABINET PREPARATION ! WARNING The cabinet must be sized to support the total weight of the hood. For the E662 hood model, the total weight is 41 lb (19 kg). If the cabinet need to be reinforced, we suggest to add wood blocks the ADD WOOD BLOCKS strengthen the connection between the bottom of the cabinet and its sides, as shown beside. HD0139 4. CUTTING HOLES See figures below for cut-out dimensions in the bottom of the cabinet. 30” CABINET BOTTOM 36” CABINET BOTTOM C C 24½” 24½” L L ¾” 2” 10”
Summary of the content on the page No. 7
5. PREPARE THE HOOD S SCREW CREW L LOCA OCATION TION 5.1 Remove filters from the hood. Remove (3) screws holding both side panels to the hood and set aside. Remove both side panels. 2 3 1 HO0042 5.2 Punch out 2 knock-out holes for electrical connections (2 on top or one on top and one on back of the hood). 5.3 Attach one wire clamp on top of the hood for the provided electrical cable with 3-prong plug. Through the wire clamp, insert this electrical cable in the hood and tighten the wire clamp to
Summary of the content on the page No. 8
6. INSTALL THE HOOD (CONT’D) 6.3 Attach the second wire clamp, insert the power cable in the hood and tighten the wire clamp to secure the cable. Place the hood under the cabinet and slide it in position. Run power cable from hood up through slot cut in cabinet. Tighten the (4) screws completely, the add the last scerw (scerw no 5) in the center keyhole. 7. CABINET BLOWER PREPARATION 7.1 VERTICAL DISCHARGE ONLY 7.1.1 Seal the metal shutoff plate on the back of the cabinet blower using duct tap
Summary of the content on the page No. 9
8. INSTALL THE BLOWER IN THE CABINET 8.1 Install the cabinet in the cabinet and rest it on th e adapter plate. If a framed cabinet is used, insert the blower as show in pictures below. STEP 1 STEP 2 HH0052 HH0053 STEP 3 HH0054 8.2 VERTICAL DISCHARGE ONLY 8.2.1 Using four (4) no. 8 x 1/2” screws provided with hood, secure the adapter to the top of the cabinet below. Remove tape from damper flap. Seal the adapter to the cabinet below using tape. HO0043 8.3 ALL DISCHARGE TYPES 2 1 8.3.1 From ins
Summary of the content on the page No. 10
9. CONNECT WIRING ! WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. Connect cable into wiring box using provided wire connectors. Connect wires as follow: WHITE to WHITE (A), BLACK TO BLACK (B), and GREEN or BARE wires under GREEN ground screws (C). DO
Summary of the content on the page No. 11
11.LIGHT BULBS This hood must use 120V, 50W max., type MR16, GU10 shielded halogen lamps. (Purchase separately). ! WARNING In order to prevent the risk of personal injury, do not install a lamp identified for use only in enclosed fixtures. NOTE: The rings must be removed from bottom banel before installing halogen lamps. 11.1 Install the lamps by placing the bulb leads into their grooves in the socket and gently push upward and turn clockwise until secured. HE0047 11.2 Install trim rings by push
Summary of the content on the page No. 12
12.OPERATION Always turn your blower on before you begin cooking to establish an air flow in the kitchen. Allow the blower run for a few minutes to clear the air after you turn off the range. HC0017 A B C D E F A) Blower OFF Delay touch pad D) OFF lighting touch pad B) ON / Blower speed control touch pad E) Halogen light touch pad C) OFF Blower touch pad / Filter maintenance touch pad F) Nightlight / keyboard lock touch pad A. BLOWER OFF DELAY TOUCH PAD: When a speed is selected, touch the delay
Summary of the content on the page No. 13
13.USE AND CARE Grease filters and side panels. The grease filters and the bottom panel should be cleaned frequently. Use a warm detergent solution. Remove grease filters by pushing them towards the back of hood and rotating downward. Clean all-metal filters in the diswasher using a non-phophate detergent. Discoloration of the filter may occur if using phosphate detergents, or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered b
Summary of the content on the page No. 14
14.WIRING DIAGRAM ! WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. 120 V Supply J5 3 Line BK BK BK nc 2 1 Return W W W Light Socket BL 50W max. J6 W Ground 3 Y Y 2 BK W Y 1 nc Light Socket 50W max. Note 3 BL (2) IEC-320 BN C14 Plug J4 G 3 BK Y [120] 4
Summary of the content on the page No. 15
15. SERVICE PARTS E662 MODEL 1 2 3 4 5 6 9 8 7 9 12 13 10 10 HL0056 11 KEY PART WIDTHS DESCRIPTION no. NUMBER 30’’ 36’’ 42’’ 1 V14971 11 1 ADAPTER/DAMPER 2 V06242 11 1 LEFT FLOW DEVIATOR 3 V06243 11 1 RIGHT FLOW DEVIATOR 4 V15931 11 1 CABINET BLOWER 5 V06263 11 1 CONTROL PCB 6 V06262 11 1 CONTROL FASCIA 7 V06750 11 1 BROAN ELITE LOGO 8 V06741 11 1 TRANSFORMER AND HARNESS KIT 9 V05917 22 2 LAMP SOCKET 10 V06268 22 2 TRIM RING V06265 2- 3 FILTERS 9.922” X 17.981” 11 V06266 -2 - FILTERS 12.922” X 1
Summary of the content on the page No. 16
16. WARRANTY WARRANTY BROAN-NUTONE LLC ONE-YEAR LIMITED WARRANTY Broan-NuTone LLC warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone LLC will, at its option,
