Summary of the content on the page No. 4
WOLF GAS COOKTOPS BEFORE YOU START Proper installation is your responsibility. COMMONWEALTH OF MASSACHUSETTS Have a qualified technician install this Installations and repairs must be performed cooktop. You must also assure that electri- by a qualified or licensed contractor, cal installation is adequate and in compli- plumber or gas fitter qualified or licensed ance with all local codes and ordinances. by the state, province, or region where this Wolf gas cooktops are manufactured for appliance
Summary of the content on the page No. 5
INSTALLATION INSTRUCTIONS SITE PREPARATION COUNTERTOP CUT-OUT DIMENSIONS LOCATION REQUIREMENTS IMPORTANT NOTE: Countertop opening Illustrations on the following pages provide the dimensions shown on the following pages overall dimensions, countertop cut-out and must be used. The dimensions shown provide installation specifications for Wolf gas for required clearances. cooktops. Maintain the following minimum installation dimensions: These cooktops are designed to fit a standard 24" (610) deep ba
Summary of the content on the page No. 6
WOLF GAS COOKTOPS INSTALLATION SPECIFICATIONS The illustrations below provide the overall IMPORTANT NOTE: When multiple cooktop dimensions, countertop cut-out and installation units are installed side by side, refer to the specifications for Model CT15G. countertop cut-out dimensions on page 9. For Model CT15G, the gas service may be supplied through the floor if the cooktop is not installed above an oven. Refer to the illustration for specifics on placement of gas and electrical. INSTALLATION S
Summary of the content on the page No. 7
INSTALLATION INSTRUCTIONS INSTALLATION SPECIFICATIONS The illustrations below provide the overall If the Model CT30G is installed above cabinets, dimensions, countertop cut-out and installation the gas and electrical placement is not critical. specifications for Model CT30G. A grounded outlet needs to be placed within 4' (1.2 m) of the right rear of the cooktop. IMPORTANT NOTE: 33" (838) wide cabinets are recommended for installation of Model IMPORTANT NOTE: When multiple cooktop CT30G. units ar
Summary of the content on the page No. 8
WOLF GAS COOKTOPS INSTALLATION SPECIFICATIONS The illustrations below provide the overall If the Model CT36G is installed above cabinets, dimensions, countertop cut-out and installation the gas and electrical placement is not critical. specifications for Model CT36G. A grounded outlet needs to be placed within 4' (1.2 m) of the right rear of the cooktop. IMPORTANT NOTE: 39" (991) wide cabinets are recommended for installation of Model When a 36" (914) built-in oven is installed CT36G. below Mode
Summary of the content on the page No. 9
INSTALLATION INSTRUCTIONS VENTILATION OPTIONS INSTALLATION OPTIONS IMPORTANT NOTE: It is recommended that MULTIPLE COOKTOP INSTALLATION you operate the Wolf gas cooktop with either a If the gas cooktop is to be used with any Wolf cooktop ventilation hood, downdraft combination of additional cooktop units or system or Pro ventilation hood. Contact your modules with a filler strip, the cut-out width is Wolf dealer for details. calculated by adding the corresponding units' OPTIONAL 1 Cooktop Wall
Summary of the content on the page No. 1
G AS C OOKTOPS
INSTALLATION INSTRUCTIONS
Summary of the content on the page No. 10
WOLF GAS COOKTOPS GAS SUPPLY REQUIREMENTS If local codes permit, a new CSA design- 1 3 certified, 4–5' (1.2–1.5 m) long, /2" or /4" ID, EXPLOSION HAZARD— flexible metal appliance connector is recom- Use a new CSA approved gas supply line mended for connecting this cooktop to the gas and install a gas shut-off valve. supply line. Do not kink or damage the flexible IMPORTANT connector when moving the cooktop. The Securely tighten all gas connections. 1 NOTE pressure regulator has /2" female pipe t
Summary of the content on the page No. 11
INSTALLATION INSTRUCTIONS GAS SUPPLY REQUIREMENTS LINE PRESSURE TESTING A 120 VAC, 60 Hz, 15-amp, fused electrical supply is required. A time-delay fuse or circuit 1 Testing above /2 psi (3.5 kPa) 14" (34.9 mb) breaker is recommended. It is recommended WC (gauge): The cooktop and its individual that a separate circuit serving only this appli- shut-off valve must be disconnected from ance be provided. the gas supply piping system during any CONTACT Electronic ignition systems operate within press
Summary of the content on the page No. 12
WOLF GAS COOKTOPS COOKTOP INSTALLATION Remove the cooktop, pressure regulator, PRESSURE REGULATOR burner grates and burner caps from the Install the pressure regulator with the arrow on shipping package. the regulator pointing up toward the unit and Lower the cooktop into the countertop cut-out in a position where you can reach the access opening. Center the cooktop in the opening cap. Refer to the illustration below. and check that the front edge of cooktop is IMPORTANT NOTE: All connections mu
Summary of the content on the page No. 13
INSTALLATION INSTRUCTIONS COOKTOP INSTALLATION SURFACE BURNERS GAS SUPPLY LINE CONNECTION INITIAL LIGHTING Assemble the flexible metal connector from The surface burners use electronic igniters in the gas supply pipe to the pressure regulator. place of standing pilots. When the cooktop You will need to determine the fittings control knob is pushed in and turned to the required, depending on the size of your gas HIGH position, the system creates a spark to supply line, flexible metal connector an
Summary of the content on the page No. 14
WOLF GAS COOKTOPS COOKTOP REMOVAL IF YOU NEED SERVICE If it is necessary to remove the cooktop for If service is necessary, maintain the quality cleaning or service, shut off the gas supply. built into your gas cooktop by calling a Wolf Disconnect the gas and electric supply. authorized service center. Remove the mounting brackets on the right To obtain the name and number of a and left side of the burner box and remove the Wolf authorized service center, check CONTACT cooktop. Reinstall in the
Summary of the content on the page No. 15
R SPARK 3 CONDUCTOR MODULE POWER CORD WHITE WHITE N 1 1 BLK 2 2 A GRN BLACK RED WHITE WHITE N A F SPARK RED MODULE WHITE REAR WHITE BLK FRONT IGN IGN IGN IGN IGN IGN IGN IGN IGN INSTALLATION INSTRUCTIONS WIRING DIAGRAMS Model CT15G LR SPARK RR SPARK 3 CONDUCTOR MODULE MODULE POWER CORD WHITE WHITE 1 1 N N BLK 2 2 GRN A A RED RED BLACK RED WHITE WHITE N N A A RED RED LF SPARK RF SPARK MODULE MODULE RED WHITE WHITE BLK BLK BLK LEFT RIGHT REAR REAR WHITE WHITE BLK RED BLK RED Model CT30G LEFT RIGHT
Summary of the content on the page No. 16
WOLF APPLIANCE COMPANY, INC. P. O. BOX 44848 MADISON, WI 53744 800-332-9513 WOLFAPPLIANCE.COM 807605 REV-B 10/2006
Summary of the content on the page No. 2
As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equip- ment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT
Summary of the content on the page No. 3
WOLF GAS COOKTOPS INSTALLATION REQUIREMENTS IMPORTANT NOTE: This installation must be completed by a qualified installer, If the information in this book is service agency or gas supplier. not followed exactly, a fire or IMPORTANT NOTE: Save these Installation explosion may result, causing Instructions for the local inspector’s use. CONTACT property damage, personal injury Please read the entire Installation Instruc- INFORMATION or death. tions prior to installation. Installer: please retain the
