Summary of the content on the page No. 1
USER MANUAL
GHP16S, GHP16W, GHP17S,
GHP17W, GHP765S, GHP775S,
GHP95S, GHP95W, GHP795S
GAS COOKTOPS
Summary of the content on the page No. 2
CONTENTS CONGRATULATiONS CONTENTS Congratulations and thank you for choosing our Product. Important safety instructions . . . . . . . . . . . . . . . . . . . . . 3 We are sure you will find your new cooktop a pleasure Installation and use summary . . . . . . . . . . . . . . . . . . . . . 4 to use and a great asset to your cooking. Before you use Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 the cookt
Summary of the content on the page No. 3
SAFETY iMPORTANT SAFETY iNSTRUCTiONS WARNING Please read the user manual carefully and store in a This appliance is not intended for use by persons handy place for later reference. The symbols you will (including children) with reduced physical, sensory see in this booklet have these meanings: or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the WARNING appliance by a person responsible for their safety.
Summary of the content on the page No. 4
iNSTALLATiON & USE iNSTALLATiON USiNG YOUR COOKTOP NOTE: You must read these warnings carefully before Note: Gas controls turn anticlockwise from ‘Off’ and installing or using the cooktop. If you need assistance, have limited movement. contact your Customer Care Department. The manufacturer will not accept liability, should the Figure 2 instructions below or any other safety instructions incorporated in this book be ignored. iNSTALLATiON • An authorised person must install this appliance an
Summary of the content on the page No. 5
CLEANiNG & CARE Pots and pans Stainless steel All common pots and pans: aluminium, stainless steel, Note: Ensure any oil is cleaned off the hob before first use, cast iron, ceramic, etc., may be used on your new gas otherwise it may cause the hob to turn a yellowish colour. model cooktop. Ensure that the pots or pans are steady and have flat bases to avoid dangerous spill-over of All grades of stainless steel may stain, discolour or attain hot liquids and wasted energy. A wok support has be
Summary of the content on the page No. 6
TROUBLESHOOTiNG If you have a problem with the cooktop, check the table below. You may be able to solve the problem and this will save you from paying for a service call. You will have to pay for a service call even in the warranty period if the problem is one listed below. FAULT POSSiBLE CAUSES REMEDY Burner will not light • Knob not held down long enough • Repeat lighting procedure and hold knob even though the sparker in ‘High’ position for flame safeguard down for 5 seconds in ‘High’ p
Summary of the content on the page No. 7
iNSTALLATiON iNSTALLATiON iNSTRUCTiONS This appliance must be installed by an authorised person CAUTION and in compliance with : 1. AS 5601 ‘Gas Installations’ (Australia) or NZS 5261 Cooktops are supplied for use with natural gas (NG). ‘Installation of Gas Burning Appliances and Equipment’ To use on LPG the injectors MUST be changed using (New Zealand) or the relevant installation code for the conversion kit supplied. Refer LP Conversion on gas appliances of your country. page 12. 2.
Summary of the content on the page No. 8
iNSTALLATiON iNSTALLATiON PROCEDURE combustible surface 1. The bench cutout should be made as per cutout Figure 5–60cm models dimensions in Figure 4. 2. Adjacent walls, cupboards and protection for combustible materials. 131mm Ensure that the appliance is installed with Section 5.12.1 of AS 5601 (Australia) or section 14.1 of NZS 5261 (New Zealand), regarding clearances to combustible surfaces and materials, and clearances to rangehoods and exhaust fans. To ensure clearances of 20
Summary of the content on the page No. 9
iNSTALLATiON Figure 6–60cm models Figure 7 seal trivet hob benchtop 10mm clamp burner box screw Figure 8–60cm and 75cm models 11mm 11mm clamp location clamp location Figure 6–75cm models 10mm clamp location Bottom view clamp location 86mm 86mm Figure 8–90cm models Figure 6–90cm models possible clamp locations 10mm possible clamp locations Bottom view 26mm 26mm 9
Summary of the content on the page No. 10
GAS CONNECTiON GAS CONNECTiON OPERATiON ON N.G./S.N.G. This appliance is supplied for use with Natural Gas. Regulator However, it can be converted for use with LPG. An appliance regulator is provided. The regulator must be Refer to LP conversion on pages 12 and 13. positioned so that the pressure test nipple is accessible when the appliance is installed. Connect the gas supply Supply pipe sizing to the ½” B.S.P. internal thread inlet of the regulator. Refer The total hourly gas consumption
Summary of the content on the page No. 11
Checking the gas supply If the regulator appears to not be performing satisfactorily, 1. Check the manometer zero point is correct. then check the following points. 2. Connect the manometer to the cooktop pressure point. 1. If the outlet pressure is consistently too low then the This is located on the regulator. inlet pressure may be too low and adjustment of an 3. Turn on the gas supply and electricity and try to ignite upstream regulator may be needed, or an upstream the gas. regulator
Summary of the content on the page No. 12
LPG CONVERSiON Under these conditions the outlet pressure should not CAUTION vary from the nominal outlet pressure of 2.60kPa by more than +/– 0.52kPa. 8. If the regulator appears to not be performing This appliance is fitted with Natural Gas burner injectors. satisfactorily then check the following points. Please follow the procedure below if a conversion to suit • If the outlet pressure is consistently too low then LP gas is required. the inlet pressure may be too low and adjustment
Summary of the content on the page No. 13
ELECTRiCAL CONNECTiON (220-240 volts) Figure 10 The appliance is supplied with a standard 7.5Amp service cord terminated by a 3-pin plug for connection Hex nut assembly, to a standard household socket. The electrical supply fully screwed down is required to power the electronic ignition system. NOTE: It will be necessary for servicing purposes to disconnect the electrical power supply. The power point should therefore be accessible after the appliance is installed, as specified in the lo
Summary of the content on the page No. 14
TESTiNG APPLiANCE OPERATiON After installation, test the appliance and ensure that it WARNING operates correctly before handing it over to the customer. Servicing must only be carried out by an authorised The following procedure is recommended: service person. 1. T urn on the gas and electricity supply and attempt ignition on all burners, both separately and in Injector sizes required for various gas types are shown in combination. (For correct procedure, refer to page 4). Table 2 (page 1
Summary of the content on the page No. 15
WARRANTY FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE: WESTINGHOUSE 4 & 5 BURNER GAS COOKTOPS This document sets out the terms and conditions of product warranties for Electrolux (a) The Appliance is damaged by: branded appliances. It is an important document. Please keep it with your proof of (i) accident purchase documents in a safe place for future reference should you require service (ii) misuse or abuse, including failure to properly maintain or ser vice for your Electrolux appl
Summary of the content on the page No. 16
For more information on all Westinghouse appliances, or for dimension and installation information, call into your retailer, phone or email our customer care team or visit our website: AUSTRALIA phone: 1300 363 640 fax: 1800 350 067 email: customercare@electrolux.com.au web: www.westinghouse.com.au NEW ZEALAND phone: 09 573 2384 fax: 0800 363 600 email: customercare@electrolux.co.nz web: www.westinghouse.co.nz TOP SERViCE Top Service encompasses the after sales service provided by The Ele
