ページ1に含まれる内容の要旨
P3PC-3062-01EN
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
CONTENTS INTRODUCTION ........................................................................... ii Regulatory Information ........................................................ ii Liability ................................................................................. iii Safety Precautions ............................................................... v Chapter1 PREPARING THE SCANNER.................................. 1 1.1 Checking the Contents of the Scanner Package............. 1 1
ページ4に含まれる内容の要旨
INTRODUCTION Thank you for purchasing the fi-5950 Duplex Color •The use of a shielded interface cable NOTICE Scanner. is required to comply with the Class B This document describes how to use fi-5950 and basic limits of Part 15 of FCC rules. The operation methods. Before you start using fi-5950 be length of the SCSI interface cable sure to thoroughly read this manual to ensure correct must be 1.5 meters (5 feet) or less. use. •The length of the AC cable must be 3 meters (10 feet) or l
ページ5に含まれる内容の要旨
About the use of mercury ■ Liability Lamp(s) inside this product contain READ ALL OF THIS MANUAL CAREFULLY mercury and must be recycled or BEFORE USING THIS PRODUCT. IF THIS g H disposed of according to local, state, or PRODUCT IS NOT USED CORRECTLY, federal laws. UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS. To avoid unexpected injuries; Also, keep this manual in a safe place so that it •Do not put the substance contained in the lamp can be easily referred to during use of t
ページ6に含まれる内容の要旨
Manufacturer Product Indication ® PFU LIMITED Windows Server 2003, Windows Windows Server (*1) Standard Edition, International Sales Dept., Imaging Business 2003 ® Division, Products Group Windows Server 2003, Solid Square East Tower, 580 Horikawa-cho, Standard x64 Edition, ® Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Windows Server 2003 Japan R2, Standard Edition, Phone : (81-44) 540-4538 ® Windows Server 2003 R2, Standard x64 Edition All Rights Reserved.Copyright © PFU LIMITED 2010 ® W
ページ7に含まれる内容の要旨
Screen Examples In This Manual In the following situation, immediately The screen examples in this manual are subject to disconnect the power cable from the AC outlet. change without notice in the interest of product Not doing so may cause a fire or electric shock. improvement. If the actual displayed screen • Smoke or heat coming from the scanner is differs from the screen examples in this manual, detected. operate by following the actual displayed screen • Strange noise or smell is det
ページ8に含まれる内容の要旨
Do not install the scanner in the following Do not place heavy objects on the scanner or locations which are subject to high perform other work on top of the scanner. temperature, humidity, less ventilation, or dust. Doing so might cause injuries or an equipment If placed in an area subject to high failure. temperature, the cover may become overheated and deformed, causing the scanner to become hot, resulting in a fire. Do not use the scanner while covered with a • A place near heat-radi
ページ9に含まれる内容の要旨
When installing the scanner on a table, make sure that the table is flat and level. Place the scanner so that none of its parts extend beyond the edge of the table, otherwise it may fall or collapse and cause injuries. Install the scanner away from strong magnetic fields and other sources of electronic noise. Protect the scanner against any static electricity and choose a static-free place to install the scanner. Static electricity can cause the scanner to malfunction. If there is an el
ページ10に含まれる内容の要旨
Chapter1 PREPARING THE SCANNER 1.1 Checking the Contents of No. Name Function the Scanner Package 9 ADF cover Button used to open the ADF open button When you unpack the scanner package, make sure that 10 Pre-imprinter For the Pre-Imprinter option the package contains all the parts on the list included in cover the package. 11 ADF The documents loaded onto the If any parts are missing or defective, contact your scan- (Automatic Hopper will be fed sheet by sheet ner dealer or an authoriz
ページ11に含まれる内容の要旨
Thick Thin Thin Thick ess Power Thickn Send to Scan Pow er T hic kness Send to Scan Hopper Heih gt Hopper Heig ht Function Function ■ Removable Parts 1.3 Operator Panel The operator panel is located on the right side of the scanner. The panel consists of a Function Number Dis- play, buttons and a LED. Function number display 1 Function Hopper Height Paper Thickness Th T in Thick Send to Sc an No. Name Description 1 Document Attached when the stacker posi- smoother Name Function tion is set
ページ12に含まれる内容の要旨
Thin Send to nd t Scan ■ Indications on the Function Name Function Number Display Scan Use this button to start linked applica- tion. The following shows the indications on the Function When this button is pressed during Number Display. scanning operation, the scanning is cancelled (*About the settings, refer to the "fi- No. Descriptions 5950 Operator’s Guide" on the SETUP Lights only one time upon turning on the scanner. DVD-ROM). Use this button to turn the power ON/ OFF. When the power i
ページ13に含まれる内容の要旨
Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2 Connecting the Scanner to Your PC 1. Place the scanner at its installation site. Connect either using the USB or SCSI interface. For details on the scanner's dimensions and required installation space, refer to the fi-5950 Operator’s Guide, chapter "10. Scanner Specifi- This scanner is provided with two inter- cations". ATTENTION faces: Ultra SCSI and USB 2.0 /1.1. Con- nect only one of the USB or SCSI cable. ATTENTION • T
ページ14に含まれる内容の要旨
3. Set the SCSI ID using the SCSI ID switch on ■ Connecting the SCSI interface the back of the scanner. When using the scanner with a SCSI interface, the fol- lowing SCSI cable and SCSI card must be purchased. • SCSI cable Use a SCSI cable whose connector on the scan- ner side is the 68-pin high-density shielded-type and whose connector on the PC side fits the con- nector of the SCSI card to use. The SCSI ID is initially set to "5" at the factory. It is recommended to use a cable of length
ページ15に含まれる内容の要旨
3. When using the SCSI cable, set the SCSI ID • Image Processing Software Option using the SCSI ID switch on the back of the A software option featuring advanced binarization of scanned images. Can be installed together with the scanner. scanner drivers (TWAIN driver/ISIS driver). (Refer to step 3 in "Connecting the SCSI interface" • Kofax VRS [VRS] on page 5.) A software program that allows you to generate high- quality images with simple operations. 4. Press the "I" side of the main powe
ページ16に含まれる内容の要旨
■ System Requirements ■ Installing the Bundled Software The system requirements for fi-5950 are as follows. The following describes how to install the bundled soft- ware from the "SETUP DVD-ROM" contained in the scanner package. ® • Windows 2000 Professional Operating There are two ways to install the bundled software: ® • Windows XP Professional system [INSTALL (Recommended)] which installs all software ® • Windows XP Professional x64 Edition programs needed to operate the scanner, or [INST
ページ17に含まれる内容の要旨
4. Install the software, following the onscreen ® ® ■ Installing Adobe Acrobat instructions. Install Adobe Acrobat using the following procedure from the "Adobe Acrobat DVD-ROM" supplied with If Kofax VRS does not support the ATTENTION the scanner. operating system, the recommended install does not install Kofax VRS. For more details. refer to "System You do not have to install Adobe Acrobat if it is Requirements" (page. 7). HINT already installed on your computer. INSTALL (Custom) 1. Ins
ページ18に含まれる内容の要旨
2.4 Checking Scanner Driver Operation This section explains how to check the operation of the installed scanner driver by using ScandAll PRO. Make sure that the scanner driver is installed properly, following the procedure below. ■ Checking the Operation of the Scanner Driver 1. Load the document on the scanner. 7. Select a scanner in the displayed dialog box. For information about how to load the document, refer To use TWAIN driver: to section "2.6 Loading Documents on the ADF for Select
ページ19に含まれる内容の要旨
10. Click [Scanner Settings]. • To remove ISIS driver, select "Fujitsu ISIS Drivers." ⇒ A setup dialog box appears for you to configure scanner driver settings. • To remove Error Recovery Guide, select "Error Recovery Guide." 11. Configure scanner settings such as the resolution and paper size. • To remove Software Operation Panel, (Software Operation Panel is automatically installed TWAIN driver/ISIS driver/Kofax VRS scanner drivers: together with TWAIN driver/ISIS driver/Kofax Configure
ページ20に含まれる内容の要旨
Appendix 1 TROUBLESHOOTING ■ Troubleshooting checklist Symptom Check this item Remedy Scanner does not turn on. Have you pushed the power button on Push the power button. the front of the scanner? Have you pushed the main power switch Push the Main power switch of the scanner. Then at the back of the scanner? push the power button. Is the AC power cable properly con- Correctly connect the AC power able to the scan- nected to the scanner? ner adapter. Disconnect the AC power cable, then connect
