ページ1に含まれる内容の要旨
RC60
Ceramic Hob
RC60SS
Ceramic Hob
User Guide
&
Installation & Service Instructions
U109915 - 02
ページ2に含まれる内容の要旨
Contents Before You Start... 1 Hob Overview 3 Cleaning Your Hob 8 Troubleshooting 9 Installation 10 Circuit Diagram 13 Technical Data 14 Warranty/After Sales Service 15
ページ3に含まれる内容の要旨
DocNo.012-0001 - Introduction - BI hob ceramic 1. Before You Start... Thank you for buying a Rangemaster hob. It should give you Never operate the hob with wet hands. many years trouble-free cooking if installed and operated Never heat unopened food containers. Pressure correctly. It is important that you read this section before you build up may make the containers burst and cause start, particularly if you have not used a ceramic hob before. injury. This appliance is designed for do
ページ4に含まれる内容の要旨
Hob Care Cleaning Never cook directly on the hob surface. The ceramic surface should be washed after use in order to prevent it from becoming scratched or dirty. Do not use the hob surface as a cutting board. In the interests of hygiene and safety, the hob should be kept Do not leave utensils, foodstuffs or combustible items on clean at all times as a build up in fats and other foodstuffs the hob when it is not is use (e.g. tea towels, frying pans could result in a fire. containing oil). Clean
ページ5に含まれる内容の要旨
DocNo.022-0001 - Overview - RC60 ceramic 2. Hob Overview Fig.2-1 ����� ����� �� �������������� � ���� ����� �� �������������� ArtNo.315-0002 RC60 ceramic hob ����� ����� �� �������������� ����� ����� �� �������������� ELECTRONIC CONTROL � ������������� ��� ���� �������� The ceramic hob comprises of four cooking zones containing Fig.2-2 heating elements with different ratings and diameters (Fig.2-1), each with a residual heat indicator. Each zone is controlled via the touch sensitive controls
ページ6に含まれる内容の要旨
Fig.2-5 � � � � � � � 1. Power ON/Power OFF 5. Zone selection indicator � 2. Cooking zone + 6. Timer control ArtNo.317-0001 60 Touch controls common 3. Cooking zone – 7. Timer display ELECTRONIC CONTROL 4. Digital display 8. TImer indicator lights (4 off) Always take care before touching the surface, even when the hob is turned off. It may be hotter than you think! Residual Heat Indicator, ‘H’ After use, a cooking zone will remain hot for a while as heat dissipates. When a hot cooking zo
ページ7に含まれる内容の要旨
To reduce the power to a cooking zone select the required Fig.2-9 zone, as indicated by the red dot in the display. Press the ‘–‘ key to reduce the power required (Fig.2-8). Note: The ‘–’ key has a repeat function: holding the key pressed down will reduce the power setting by one level every 0.3 seconds. To shutdown a cooking zone: ArtNo.317-0004 60 Reducing power Make sure the required cooking zone has been selected, as indicated by the red dot in the display. Reduce the power to 0 (Fig.
ページ8に含まれる内容の要旨
Timer Function Fig.2-15 The timer has two settings: • Zone timer • Minute timer ArtNo.317-0007 60 Setting the zone timer Zone timer This allows each cooking zone to be set to cook up to a maximum of 99 minutes at a set power level. At the end of the cooking time the zone will turn off automatically. Activating the timer: Select the required cooking zone and then: 1. Using the ‘+’ and ‘–‘ keys, set the desired cooking Fig.2-16 temperature. 2. Press the timer key (Fig.2-15): the timer display w
ページ9に含まれる内容の要旨
Turning off the timer alarm: Fig.2-19 At the end of the cooking time the hob will beep steadily for 2 minutes. Press any key to stop the alarm. Deactivating the timer: ArtNo.317-0007 60 Setting the zone timer Make sure that none of the cooking zones has been selected. Press the timer and ‘–‘ keys simultaneously. The timer display will go out. ������������������ ����� ��� ����� ���� Child Lock Function This allows the control panel to be locked to prevent any accidental use. Fig.2-20 IMPORTANT
ページ10に含まれる内容の要旨
DocNo.042-0001 - Cleaning - BI hob ceramic 3. Cleaning Your Hob Essential information Cleaning burned-on spills Allow the hob to cool and isolate the electricity supply before Make sure that the residual heat indicators are off and that carrying out any thorough cleaning. the hob is cool. Remove the excess burned-on substance with a single-edged razor scraper. Hold the scraper at an angle of Never use paint solvents, washing soda, caustic cleaners, about 30° to the surface and then scrape off
ページ11に含まれる内容の要旨
DocNo.052-0001 - Troubleshooting ceramic & induction 4. Troubleshooting If there is an installation problem and I don’t get my original installer to come back to fix it, who pays? You do. Service organisations will charge for their call- outs if they are correcting work carried out by your original installer. Therefore, it’s in your own interest to keep track of this installer so that you can contact them as required. A crack has appeared in the hob surface. Isolate the hob immediately from
ページ12に含まれる内容の要旨
INSTALLATION Check the appliance is electrically safe when you have finished. DocNo.062-0001 - Installation - RC60 hob 5. Installation Dear Installer Location of the Hob Before you start your installation, please complete the details The hob may be installed in a kitchen/kitchen diner but NOT BELOW. in a room containing a bath or shower. Should your customer have a problem relating to your This appliance is designed for domestic cooking only. Use for installation they will be able to contact yo
ページ13に含まれる内容の要旨
INSTALLATION Check the appliance is electrically safe when you have finished. Positioning the Hob Fig.5-1 ��� ��� The hob should be fitted into a work surface, which is at least 600mm deep. In position, it has a maximum thickness of 5mm from the top of the work surface. The cut-out dimensions are shown in (Fig.5-1) and the minimum clearances in ArtNo 314-0006 60cm induction dimensions �� (Fig.5-2). The minimum recommended distances from the hob to nearby surfaces are shown in (Fig.5-3). ���
ページ14に含まれる内容の要旨
INSTALLATION Check the appliance is electrically safe when you have finished. Electrical Connections Fig.5-5 This appliance must be installed by a qualified electrician to comply with the relevant Institute of Electrical Engineers (I.E.E.) regulations and also the local electricity supply company requirements. WARNING: THIS APPLIANCE MUST BE EARTHED ArtNo.317-0017 Connection box Note: All external wiring must comply with the IEE Regulations for the Electrical Equipment of Buildings. Conne
ページ15に含まれる内容の要旨
DocNo.091-0001 - Circuit diagram - RG60/RGG60 gas 7. Circuit Diagram N L � ArtNo.080-0015 - RG60/RGG60 circuit diagram � � � � A Spark generator B Ignition switch 13
ページ16に含まれる内容の要旨
DocNo.102-0001 - Technical data - RC60 7. Technical Data INSTALLER: Please leave these instructions with the user. DATA BADGE LOCATION: Base of the hob COUNTRY OF DESTINATION: GB/IE Dimensions Below worktop: 40mm Height Above worktop: 5mm (60mm including connection box) Overall width 580mm; see ‘Positioning of the hob’ Overall depth 510mm Space for fixing See ‘Positioning of the hob’ Minimum space above hotplate 650mm Connections Electric 220 – 240V 50Hz Ratings Maximum electric load at 230V
ページ17に含まれる内容の要旨
DocNo.111-0001 Warranty 8. Warranty/After Sales Service If consultation or technical assistance is needed, please provide the local authorised service agent with the purchase invoice and the product code/serial number. The 2 years free maintenance for the operation of the appliance started from the date of purchase of this product. Any cosmetic damage to the appliance must be reported within 90 days of delivery. For in-warranty service please call: 0845 6035312. For general enquiries please
ページ18に含まれる内容の要旨
16
ページ19に含まれる内容の要旨
17
ページ20に含まれる内容の要旨
DocNo.000-0001 - Back cover Rangemaster � � �� � ����������� �������� ������� ������� �� w w w . r a n g e m a s t e r . c o . u k ArtNo.000-0003 CE logo
