ページ1に含まれる内容の要旨
Users Guide
&
Installation Instructions
ページ2に含まれる内容の要旨
CONTENTS IMPORTANT SAFETY INFORMATION Installation Page 2 Child Safety 2 Maintenance and Service 3 YOUR APPLIANCE 4 OPERATING INSTRUCTIONS Cooker Hood Controls 4 Worktop Lighting 4 Fan 4 To Operate 5 Recirculation 5 Extraction 5 MAINTENANCE AND CLEANING Cleaning 6 Metal Grease Filters 6 Charcoal Filters 7 To Remove/Replace the Charcoal Filters 7 To Replace a Light Bulb 7 INSTALLATION INSTRUCTIONS Technical Information 8 ELECTRICAL CONNECTION Electrical Requirements 9 Electrical Connection 9 INST
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about the meaning of any of these warnings contact the Helpline. • If the room where the cooker hood is to be • INSTALLATION used contains a fuel burning appliance such • Any installation work must be underaken as a central heating boiler then its flue must by a qualified elect
ページ4に含まれる内容の要旨
IMPORTANT SAFETY INFORMATION • MAINTENANCE AND SERVICE • This appliance can be a hazard if the grease filters and charcoal filters are not cleaned and replaced as recommended. • Always insist on genuine RANGEmaster spare parts. • Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunction. In the event of your chimney hood requiring service contact: RANGEmaster Helpline: 0845 603 5312, or Co
ページ5に含まれる内容の要旨
YOUR APPLIANCE OPERATING INSTRUCTIONS The chimney hood is designed to extract FAN unpleasant odours from the kitchen, it will not The switch (M) marked with the fan symbol and extract steam. The appliance can be installed the switch (V) marked 1-2-3 operates the fan. to recirculate or extract contaminated air. M 0 - OFF COOKER HOOD CONTROLS 1 - ON The chimney hood functions are controlled V 1 - Low by three manual slide switches located on the 2 - Normal right, on the underside of the canopy. 3
ページ6に含まれる内容の要旨
OPERATING INSTRUCTIONS TO OPERATE Select the required fan speed and light if required. RECIRCULATION In the recirculation mode contaminated air enters the chimney hood through the grease filter cassettes. The air is cleaned by the charcoal filters and leaves through the grilles in either side of the chimney stack. EXTRACTION In the extraction mode the contaminated air enters the chimney hood passing through the grease filter cassettes and is passed out through the ducting into the atmosphere. To
ページ7に含まれる内容の要旨
MAINTENANCE AND CLEANING Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood. Special attention should be paid to the grease filter cassettes and charcoal filter when the hood is used in the recirculation mode. Before carrying out any Remove the metal grease filters one at maintenance or cleaning isolate the a time, by pressing the release catch cooker hood from the mains towards the rear of the chimney hood as supply. illus
ページ8に含まれる内容の要旨
MAINTENANCE AND CLEANING CHARCOAL FILTERS (2) In the recirulation mode the activated charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned or regenerated and must be replaced every four months, or more frequently if the hood is used consistently over 4 hours per day. To remove the charcoal filters, first remove the metal grease filters. Holding one filter at a time, turn it anti- clockwise (B) as illustrated opposite. We recommend that you wear rubber gloves
ページ9に含まれる内容の要旨
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. TECHNICAL INFORMATION DIMENSIONS CANOPY: Height 240mm Width (60cm version) 598mm (90cm version) 898mm (120cm version) 1198mm Depth 490mm CHIMNEY: Height (Upper Section) 415mm (Lower Section) 560mm ELECTRICAL SUPPLY VOLTAGE: (50Hz) 230V POWER CONSUMPTION: 225W FAN MOTOR: 145W LIGHT BULB: 2 x 40W
ページ10に含まれる内容の要旨
ELECTRICAL CONNECTION THIS APPLIANCE MUST BE EARTHED ELECTRICAL REQUIREMENTS Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). ELECTRICAL CONNECTION Before connecting to the mains supply ensure t
ページ11に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD responsibility for damage due to incorrect INSTALLATION REQUIREMENTS installation of the cooker hood or if the hood is Please ensure that when the appliance is not installed in compliance with relevant installed it is easily accessible to an engineer regulations controlling this type of installation. in the event of a breakdown. UNPACKING All installations must comply with The cooker hood is supplied with the the local authorities requirements following components for
ページ12に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD 4. Draw a horizontal line through the vertical CLEARANCE HEIGHTS at X. X is the distance between the centre The chimney hood is designed to be fitted of the top and bottom fixing holes on the over a cooking appliance. A minimum upper chimney stack. Mark the centre clearance height of 650mm (25˚ins) is positions for the middle bracket fixing required when installed above a built-in screws (3) at 95mm either side of the electric hob, or 700mm (27˚ins) when vertical
ページ13に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD Note: If the hood is to be installed onto a The ducting used must be125mm (5 hollow construction or plaster or partition ins), flexible or rigid and must be board wall then special fixing screws will manufactured from fire retardant be required (not supplied). material, produced to BS.476 or DIN 4102-B1. The choice should be made FITTING THE CANOPY by the installer. However, we recommend flexible ducting should HOOD only be used as an accessory as 1. Rotate the adjust
ページ14に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD RECIRCULATION If you are using the hood for recirculation, ensure the charcoal filters are in position following the instructions contained in the section “To Remove/Replace the Charcoal Filters”. Note: When the hood is used in the recirculation mode ensure that the plate (T) has been fixed into the lower chimney section. If not, fit the plate as illustrated opposite using two of the self tapping screws provided in the fixing kit. FITTING THE CHIMNEY STACK The chimney
ページ15に含まれる内容の要旨
INSTALLING THE CHIMNEY HOOD FITTING THE FRONT RAIL These instructions apply to models as follows: - CLAHDC60BB/ CLAHDC90BB/, CLAHDC90BC/ CLAHDC120BB/, CLAHDC120BC/ Do not fit the front rail until the chimney hood is mounted on the wall. 1. Use a 4mm Allen key to fix the mounting brackets to the front of the canopy using the screws provided. 2. Use the plastic plugs provided to cover the screw heads. NB When fitted the rail should be below the level of the fixings. 14
ページ16に含まれる内容の要旨
4329641 02 020412
