ページ1に含まれる内容の要旨
Freestanding cooker
Installation instructions
OR90SBDSIX models
and User guide
NZ AU
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
1 Contents Safety and warnings 2 Installation instructions 8 First use 16 Using your oven 19 Cooking functions 22 Cooking guide 25 Using the rotisserie 26 Using the electronic timer 28 Automatic cooking 29 Induction cooktop introduction 30 Choosing the right cookware 32 Using your induction cooktop 34 Using your cooktop’s special features 35 Cooking guidelines 37 Care and cleaning 38 Cooktop fault codes 52 Troubleshooting 52 Warranty and service 55 Important! SAVE
ページ4に含まれる内容の要旨
2 Safety and warnings Installation WARNING! Electrical Shock Hazard If the ceramic glass cooktop surface becomes cracked, switch the appliance off at the mains power supply and call an Authorised Service Agent. Always disconnect the cooker from the mains electricity supply before carrying out any maintenance operations or repairs. Failure to follow this advice may result in death or electrical shock. WARNING! Cut Hazard Take care - panel edges are sharp. Failure to use caution could result
ページ5に含まれる内容の要旨
3 Safety and warnings Electrical This cooker is to be installed and connected to the electricity supply only by an authorised person. If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the electrical system is suitable for the electricity drawn by the cooker. The appliance must be connected to the mains electricity supply, checking that the voltage corresponds to the value given in the rating
ページ6に含まれる内容の要旨
4 Safety and warnings Operation Your freestanding cooker has been carefully designed to operate safely during normal cooking procedures. Please keep the following guidelines in mind when you are using it: WARNING! Explosion Hazard Do not store flammable materials such as gasoline near the cooktop. Do not store flammable material in the oven or storage compartment. Do not spray aerosols near the cooktop during use. Failure to follow this advice may result in death or serious injury. WARNING!
ページ7に含まれる内容の要旨
5 Safety and warnings WARNING! Health Hazard This appliance complies with electromagnetic safety standards. However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their doctor or implant manufacturer before using this appliance to make sure that their implants will not be affected by the electromagnetic field. Failure to follow this advice may result in death. WARNING! Hot Surface Hazard Accessible parts may become hot when this coo
ページ8に含まれる内容の要旨
6 Safety and warnings Important safety instructions Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers may ignite. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame eg with a lid or a fire blanket. WARNING: Danger of fire: do not store items on the cooking surfaces. Do not use your cooktop as a work surface. Do not use a steam cleaner on any part of your cooker. Isolating switch: make sure this
ページ9に含まれる内容の要旨
7 Safety and warnings Important safety instructions Do not use harsh abrasive cleaners or sharp metal scrapers to clean the ceramic glass cooktop and the oven door glass since they scratch the surface, which may result in shattering of the glass. Some heavy-duty and nylon scourers can scratch the ceramic glass cooktop. Always read the label to check if your scourer is suitable for cleaning ceramic glass cooktops. Do not use pans with rough circular base as these may scratch your cooktop.
ページ10に含まれる内容の要旨
8 I Installa nstallation instruc tion instructions tions Dimensions and clearances The cooker must be installed no less than 50 mm away from any side walls which exceed the height of the cooktop. The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand temperatures of 65 °C above room temperature. Do not install the cooker near flammable materials (eg curtains). If you stand the cooker on a pedestal, make sure you provide safety measure
ページ11に含まれる内容の要旨
9 Installation instructions Cooker overall dimensions [mm] • height: min 897 - max 910 • product width: 897 • depth: 600 • cavity width 900 Fig. 2 Dimensions and distances from cooker 500 mm 50 mm 650 mm 450 mm
ページ12に含まれる内容の要旨
10 I Installa nstallation instruc tion instructions tions Levelling the cooker Important! Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface. For ease of installation, first remove the kickstrip. To remove the kickstrip, unscrew the two screws holding it in place. The cooker is already fitted with four levelling feet. Level the cooker
ページ13に含まれる内容の要旨
11 Installation instructions Fitting the anti-tilt bracket Important! To restrain the appliance and prevent it tipping accidentally, the anti- Dotted line showing the position of the cooker when installed tilt bracket and restraining plate supplied must be fitted according to the instructions below. 1 Drill four 8mm diameter holes for Fig. 4 Attaching the the fixing screws (two in the wall anti-tilt bracket and and two in the floor-see Fig.4) and Anti-tilt sliding the cooker bracket in
ページ14に含まれる内容の要旨
12 I Installa nstallation instruc tion instructions tions Moving the cooker Important! To prevent damaging the adjustable feet or lower trim, ensure the cooker is always lifted by two people. Do not lift the cooker by the door handles. DO NOT DRAG the cooker. Lift the feet clear of the floor. Fig. 8 Correctly lifting the cooker Fig. 9 Incorrectly lifting the cooker Fig. 10 Incorrectly moving the cooker C B Fixing the backguard Before installing the cooker, assemble the backguard “C” . A Th
ページ15に含まれる内容の要旨
13 Installation instructions Connecting the power supply cable Important! This cooker must be connected to the electricity supply only by an authorised person. To connect the power supply cable to the cooker, it is necessary to: 1 Unhook the terminal board cover by inserting a screwdriver into the two hooks ‘A’ (fig. 12). 2 Unscrew the screw ‘D’ and open completely the cable clamp ‘E’ (figs. 14). 3 Position the U bolts ‘F’ onto terminal board ‘G’ (figs. 14) according to the diagrams in fig.
ページ16に含まれる内容の要旨
14 Installation instructions Feeder cable section In Australia and New Zealand: this cooker must be connected to electrical supply using V105 insulated cable. 2 220-240 V~ 3 x 6 mm (*) 2 380-415 V 3N~ 5 x 2,5 mm (*) 2 380-415 V 2N~ 4 x 6 mm (*) * Connection with wall box connection. - Diversity factor applied. - A diversity factor may be applied to the total loading of the appliance only by a suitably qualified person. 1 1 G G 2 2 L1 L1 3 F 3 F L2 4 4 N L2 5 5 N D PE D PE 380-
ページ17に含まれる内容の要旨
15 Installation instructions Wiring diagram R1 TL TL1 R2 IU-LH S1 PT1 P8 PR PR PT2 P9 3a 4a 5a 6a 7a 8a 9a 10a 11a 1a 2a 12a PCB F1 3 4 5 6 7 8 9 10 11 F1 1 2 12 L1 N X6/X18/X19 ST CIGS C X1 X2 X8 V GIR LF UD CF X0 TS PB P4 LF TR RSI RSI RSI RSI X6/X18/X19 S2 PR X1 EC L1 N T IU-RH 42 ELECTRIC DIAGRAM KEY M 5 3 1 F1 Oven switch C Oven top heating element ST Safety thermostat G Oven grill heating element TL Thermal overload S Oven bottom heating element TL1 Induction hob thermal overload CI Oven
ページ18に含まれる内容の要旨
16 First use 29 10 134 5678 Fig. 15 Control panel 1 Control buttons 7 Rear right cooking zone dial 2 Clock display 8 Front right cooking zone dial 3 Temperature dial 9 Function indicator light 4 Function dial 10 Temperature indicator light 5 Front left cooking zone dial 6 Rear left cooking zone dial
ページ19に含まれる内容の要旨
17 First use Buttons sets the timer 12:00 A sets the cooking time sets the stop time for automatic cooking set the oven temperature / select Celsius or Fahrenheit decreases the time and temperature increases the time and temperature Fig. 16 Clock display and control buttons Illuminated symbols If the display shows It means that... For more information The clock needs to be set. See instructions below. flashing 12:00 The oven is set for automatic steadily lit cooking. See section ‘Autom
ページ20に含まれる内容の要旨
18 First use Remove the side racks to fit the Catalytic panels (if not already fitted) 1 Remove all shelves and trays. 2 For easier access to the fixing screws, you may remove the oven door first. See ‘Removing and refitting the oven door’ in Care and Cleaning. 3 Remove the side racks on both sides: 3a Using a small coin or a flat-head screwdriver, loosen and remove both fixing screws. 4a Gently remove the side rack. Fig. 17 Removing the side racks Fitting the Catalytic panels 5 Fit the c
