ページ1に含まれる内容の要旨
1
Installation instructions
and User guide
Gas cooktops
CG604 models
NZ AU
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Contents 1 Safety and warnings 2 Installation instructions 6 Introduction 16 Using your cooktop 18 Care and cleaning 23 Troubleshooting 27 Warranty and service 28 Important! SAVE THESE INSTRUCTIONS The models shown in this User Guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Payk
ページ4に含まれる内容の要旨
2 Safety and warnings WARNING! Cut Hazard Beware of sharp edges when handling stainless steel appliances. Failure to use caution could result in injury or cuts. WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains. Connection to a good earth wiring system is absolutely essential. Failure to follow this advice may result in death or electrical shock. Important safety precautions Installation Read the
ページ5に含まれる内容の要旨
3 Safety and warnings Particular attention shall be given to the relevant requirements regarding ventilation. This product should not be sealed into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for costs associated with releasing such a product, nor for repairing damage that may be incurred in doing this. When this product is installed it shall not be used as a space heater, especially if installed in boats or carav
ページ6に含まれる内容の要旨
4 Safety and warnings WARNING! Hot Surface Hazard This appliance becomes hot during use. Do not touch the cooktop components, burners, trivets/pan supports or the base when hot. Before cleaning, turn the burners off and make sure the whole cooktop is cool. Failure to do so may result in serious injury. WARNING! Explosion Hazard Do not store fl ammable materials such as gasoline near the cooktop.Do not spray aerosols near the cooktop during use. Failure to do so may result in death or seriou
ページ7に含まれる内容の要旨
5 Safety and warnings Important safety precautions Operation Children, or persons with a disability which limits their ability to use the appliance, should have a responsible person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to themselves or their surroundings. If the electrical supply cord is damaged, it must only be replaced by an authorised person. Ensure that the electrical connection plug is accessible after installat
ページ8に含まれる内容の要旨
0 200 560 –2 580 34 6 Installation instructions This cooktop has been designed and constructed in accordance with the following codes and specifications: AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances AS/NZS 60335-1 General Requirements for Domestic electrical appliances AS/NSZ 60335-2-6 Particular Requirements for Domestic electrical cooking appliances AS/NSZ 1044 Electromagnetic Compatibility Requirements. The installation shall comply with the dimensions in Figu
ページ9に含まれる内容の要旨
200 mm min 500 mm 7 Installation instructions Clearances Installation clearances and protection of combustible surfaces shall comply with the current local regulations e.g. AG 601 (AS 5601) - Gas Installations code. Fig. 2 Fig. 3 60 mm min 450 mm 750 mm 20 mm
ページ10に含まれる内容の要旨
8 Installation instructions Fastening the installation brackets (fig. 4) Each cooktop is provided with an installation kit including brackets and screws for fastening the top to fixture panels from 2 to 4 cm thick. Turn the cooktop upside down and fasten the brackets “F and R” to the appropriate socket holes, without tightening the screws “B” for the moment. Make sure that the brackets are fastened as shown in figure 4. Fastening the cooktop (fig. 4) Spread the sealing material “C” out al
ページ11に含まれる内容の要旨
9 Installation instructions Gas supply The connection must be executed by an authorised person according to the relevant standards. Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the gasket has been placed (figures 5 and 6). Conical adaptor and gasket are supplied with the appliance (packed with conversion kit for use with Natural gas or Universal LPG). This appliance is suitable for use with Natural Gas or
ページ12に含まれる内容の要旨
10 Installation instructions 1 After connecting the gas supply, check the piping and connections for leaks using a soap and water solution. The presence of bubbles indicates a leak, tighten or replace connections as appropriate. Important! Do not use any naked flame to check for leaks. 2 The operation of the appliance MUST be tested before leaving. 3 Adjust the test point pressure or supply pressure to the value which is appropriate for the gas type. 4 Turn on the appliance gas controls
ページ13に含まれる内容の要旨
11 Installation instructions Conversion procedure (to convert to Universal LPG) replacing the injectors. Important! The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or Universal LPG (check the “gas type” sticker attached to the appliance). See the “Table for the choice of injectors” for the nominal gas con- sumption and injector size details. To replace the injectors proceed as follows: Remove pan supports
ページ14に含まれる内容の要旨
12 Installation instructions Minimum burner setting adjustment When changing from one type of gas to another, the minimum tap output must also be cor- rect, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum to the minimum position. The adjustment is performed with the burner lit, as follows: Turn the knob to the minimum position. Remove the tap knob. On gas valves provided with adjustment screw in the
ページ15に含まれる内容の要旨
13 Installation instructions Important! Installation must be carried out according to the manufacturer's instructions. Incorrect installation may cause harm and damage to people, animals or property, for which the manufacturer accepts no responsibility. Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains. Connection to a good earth wiring system is absolutely essential. The manufacturer accepts no responsibility for a
ページ16に含まれる内容の要旨
14 Installation instructions Important! Replacing the power cord must be done by a qualified electrician in accordance with the instructions supplied by the manufacturer and in compliance with established electrical regulations. Electric diagrams key PA Ignition switch A Ignition coil M Terminal block CA Spark electrode CA CA NL CA M CA A PA PA PA PA Fig. 11
ページ17に含まれる内容の要旨
15
ページ18に含まれる内容の要旨
16 Introduction About your new cooktop Thank you for buying a Fisher & Paykel gas cooktop. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start. This guide introduces you to all its special features. We recommend you read the whole guide before using your new cooktop, for both safety and cooking success. For more information, go to www.fisherpaykel.com Before using your new cooktop Before using your new cook
ページ19に含まれる内容の要旨
17 Introduction 2 2 5 3 Fig.1 CG604 with rapid burner 1 (no flame failure safety feature) 2 2 2 2 5 5 4 4 1 1 Fig.2a CG604 with wok burner Fig.2b CG604 with wok burner ( with flame failure safety feature) (no flame failure safety feature) 1 Auxiliary burner 2 Semi-rapid burner 3 Rapid burner 4 Wok burner 5 Cooktop controls
ページ20に含まれる内容の要旨
18 Using your cooktop Gas burners The knob (Fig. 3) controls the flow of gas through the safety tap. OFF = closed valve = maximum aperture or flow = minimum aperture or flow You can choose to cook at any heat between and , but never between and OFF. Fig. 3a Burner knob and symbols (models without flame failure safety feature) Fig. 3b Burner knob and symbols (models with flame failure safety feature)
