ページ1に含まれる内容の要旨
Gas Hob
INSTRUCTION BOOKLET
Models EHG 672 - EHG 674 - EHG 675
GB
35670-2601
2
ページ2に含まれる内容の要旨
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 522799 Installation l This hob must be installed by qualified personnel, l When using other electrical appliances, ensure the according to the manufacturer’s instructions and to cable does not come into contact with the hot the relevant British Standards. surfaces of the cooking appliance. l Any gas installation must be carr
ページ3に含まれる内容の要旨
Contents For the Installer For the User Technical Data Page 12 Description of the Hob Page 5 Important Safety Requirements Page 13 Operation Page 6 Installation Page 14 Maintenance and Cleaning Page 7 Gas Connection Page 14 Something Not Building In Page 15 Working? Page 8 Electrical Connection Page 16 Service and Wiring Diagram Page 17 Spare Parts Page 8 Fault Finding Page 18 Guarantee Conditions Page 9 Commissioning Page 20 Electrolux Service Force Servicing Page 21 Centre Addresses Page 10 Co
ページ4に含まれる内容の要旨
Description of the Hob 3 1 3 2 EHG 672 5 6 7 4 8 9 3 1 3 2 5 6 1. Hob Top 7 4 2. Rapid Burner 8 EHG 674 9 3. Semi-rapid Burners EHG 675 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) 9. Electric Ignition Push Button INSTALLATION WHEN THE HOB IS FIRST INSTALLED Any gas installation must be carried out by Once the hob has been in
ページ5に含まれる内容の要旨
Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to maximum position. At the same time push the electric ignition button which is marked with a little spark.. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after i installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only
ページ6に含まれる内容の要旨
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for no
ページ7に含まれる内容の要旨
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Electrolux Service Force Centre. SYMPTOM SOLUTION n There is no spark when lighting the gas u Check that the unit is plugged in and the electrical supply is switched on u Check that the RCCB has not tripped (if fitted) u Check the mains fuse has not blown u Check the burner cap and crown have been replaced correctly, e.g. after cleaning. n The gas ring burns unevenl
ページ8に含まれる内容の要旨
Guarantee Conditions * Appliances found to be in use within a ELECTROLUX STANDARD GUARANTEE commercial or similar environment, plus those CONDITIONS which are the subject to rental agreements. We, Electrolux, undertake that if, within 12 months * Products of Electrolux manufacture which are not of the date of the purchase, this Electrolux appliance marketed by Electrolux. or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we European Guarantee wi
ページ9に含まれる内容の要旨
ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 ISLE OF LEWIS ND Macleod NORTH EAST CHANNEL ISLANDS (M69) 16 James Street Stornoway GUERNSEY Guernsey Electricity GATESHEAD Unit 356a Isle of Lewis PO Box 4 (M39) Dukesway Court PA872QW Vale , Guernsey Dukesway Channel Islands Team Valley KELSO 2-8 Wood Market (M08) Kelso Gateshead JERSEY Jersey Electricity Borders TD5 7AX NE11 0BH Company PO Box 45 GRIMSBY Unit 2 ORKNEY Corsie Domestics Queens
ページ10に含まれる内容の要旨
ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 MIDLANDS LONDON & EAST ANGLIA SOUTH EAST BIRMINGHAM 66 Birch Road East, CANVEY ISLAND 2-4 Sandhurst ASHFORD Unit 2 (M18) Wyrley Road Industrial Kings Road (M58) Bridge Road Business Estate Canvey Island Estate Witton SS8 0QY Bridge Road Birmingham Ashford CHELMSFORD Hanbury Road B67DB Kent (M47) Widford Ind Estate TN2 1BB BOURNE Manning Road Ind Chelmsford (M44) Estate Essex FLEET Unit 1 Pinfold
ページ11に含まれる内容の要旨
Instructions for the Installer Engineer technical data OVERALL DIMENSIONS SUPPLY CONNECTIONS Width: 580 mm. Gas: Depth: 500 mm. RC 1/2 inch (1/2 inch male) Rear right hand corner Height: 88 mm. Weight: 8 Kg. Electric: 230-240V 50Hz supply, 3 core flexible cable with CUT OUT DIMENSIONS non rewireable plug fitted with a 3 amp cartridge fuse. Width: 550 mm. Depth: 470 mm. This appliance complies with the EEC Directive No Thickness: 30 mm. 89/336, concerning suppression of radio electrical interfer
ページ12に含まれる内容の要旨
50 mm 100 mm 50 mm 100 mm 50 mm 50 mm 600 mm Important safety requirements This hob must be installed in accordance with the Gas Location Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). The hob may be located in a kitchen, a kitchen/diner Detailed recommendations are contained in the or bed sitting room, but not in a bathroom or shower following British Standards Codes Of Practice: B.S. room. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Curr
ページ13に含まれる内容の要旨
580 550 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the di
ページ14に含まれる内容の要旨
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or It is also recommended to carry out the electrical drawer it will be necessary to fit a heat resistant board connection to the hob as shown in diagrams 1 and 2. below the base of the hob on the underside of the work surface. ON/OFF SWITCH ON/OFF SWITCH 1 2 3 a 60 FLEX OUTLET b FLEX OUTLET FO 0764 FO 0763 FO 1013 Dimensions are given in mm. Building over a kitchen unit with door Proper arrangements mu
ページ15に含まれる内容の要旨
Electrical connections Any electrical work required to install this Permanent Connection hob should be carried out by a qualified In the case of a permanent connection, it is necessary electrician or competent person, in that you install a double pole switch between the hob and the electricity supply (mains), with a minimum accordance with the current regulations. gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with THIS HOB MUST BE EARTHED. th
ページ16に含まれる内容の要旨
Wiring diagram L 1 A 0 2 3 220/240 4 B N A. IGNITOR SWITCH B. IGNITOR UNIT 17
ページ17に含まれる内容の要旨
Fault Finding Preliminary Electrical Systems Check PLUG (with cover removed) SOCKET (face view) Earth Wire ( ) Green/Yellow ( ) E Blue Brown Green Yellow START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity N L check. Blue Green Brown Yellow Carry out: Electricity supply NO YES Carry out: D: Resistance to should now be C: Polarity check. Earth check. satisfactory. A. EARTH CONTINUITY CHECK - Has inlet fuse blown? Appliance must be electrically disconnected - meter se
ページ18に含まれる内容の要旨
Ignition System / Gas Ignition YES Check gas supply at Ignitor does not spark burner NO Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check position of the Check earth continuity electrode of appliance Check fitting of burners Check continuity from 'N' on the Check continuity from the tip of mains connector block and "O" on each electrode to the terminals 1 the ignitor unit to 4 on the ignitor
ページ19に含まれる内容の要旨
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. FO 1032 + Remove the control knob. a) Minimum adjustment screw You can find tw
ページ20に含まれる内容の要旨
Servicing A: Removal Of Hob Top D: Removal Of Burner 1. Remove all control knobs, pan supports, burner caps and crowns. 1. Follow the procedures in Section A. 2. Remove 2 screws from each burner. 2. With the aid of a 12mm spanner loosen off the pipe 3. Lift the hob top at the rear and disengage it from the connection nut. front locators. 3. From the underside of the hob remove 2 self tapping 4. Remove fixing nut from generator and earth lead to screws from the burner body. hob. 4. Reassemble in
