ページ1に含まれる内容の要旨
®
®
MultiSync
MultiSync
™
™
LCD400V
LCD400V
User’s Manual
User’s Manual
Contents 1
Quick Start 2-3
Controls 4-5
Recommended Use 6-7
Specifications 8
Features 9
Troubleshooting 10
References 11
Limited Warranty 12
78133331 1 9/25/98, 12:46 PM
ページ2に含まれる内容の要旨
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
ページ3に含まれる内容の要旨
NEC MultiSync Monitors Receive a $25 Purchaser Rebate to thank you for choosing an ® NEC MultiSync LCD Monitor That’s right. Simply complete and return this regisitration, and we’ll send the purchasing party a check for $25.00 And we’ll also enter you in our “100,000 Give Away II” for a chance to win $5,000, $25,00 or $50,000! Thank Uou for your time, and thanks for choosing NEC. ® MultiSync LCD400V ™ User’s Manual SEE, HEAR AND FEEL THE DIFFERENCE. Contents 1 Quick Start 2-3 Controls 4-5 R
ページ4に含まれる内容の要旨
Quick Start ® To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. ™ For the Mac: Connect the MultiSync LCD400V Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the MultiSync LCD400V Macintosh cable
ページ5に含まれる内容の要旨
Quick Start Figure C.1 Figure D.1 Power Switch Figure E.1 3 78133331 5 9/25/98, 12:46 PM
ページ6に含まれる内容の要旨
Controls ™ OSM (On-Screen-Manager) Controls The OSM controls on the front of the monitor function as follows: Control Main Menu Sub-Menu EXIT Exits the OSM controls. Exits to the OSM controls main menu. CONTROL / Moves the highlighted Moves the highlighted area area up/down to select up/down to select one of the one of the controls. controls. CONTROL –/+ Has no function. Moves the bar in the + or – direction to increase or decrease the adjustment. PROCEED Proceeds to the selected Activates Auto
ページ7に含まれる内容の要旨
Controls ™ AccuColor Control System Color presets select the desired color setting. If a setting is adjusted, the name of the setting will change to Custom. Color Gain (Red, Green, Blue): Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the color bars. ™ OSM Location You can choose where you would like the OSM control image to appear on your screen. Selecting OSM L
ページ8に含まれる内容の要旨
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place
ページ9に含まれる内容の要旨
Recommended Use CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes. The optimal d
ページ10に含まれる内容の要旨
Specifications ® ™ Monitor MultiSync LCD400V Notes Specifications Monitor LCD Module Diagonal: 14.1 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 14.1 inch liquid crystal display (LCD); 0.28 mm dot 2 Native Resolution (Pixel Count): 1024 x 768 pitch; 200cd/m white luminence; 150:1 contrast ratio, typical Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Positive/Neg
ページ11に含まれる内容の要旨
Features Analog Advantage: Capable of displaying unlimited colors in a continuous spectrum, providing a truer representation of color. The monitor’s high contrast LCD enhances color vibrancy and improves focus with no geometric distortion. Wider Compatibility: Because the MultiSync LCD monitor is analog through and through, it does not require special analog to digital display or interface cards but can accept RGB input directly. Reduced Footprint: Provides the ideal solution for environments re
ページ12に含まれる内容の要旨
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and recommended
ページ13に含まれる内容の要旨
References • BBS (508) 635-4706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (508) 635-4298 • Electronic Channels: Internet e-mail: tech-support@nectech.com Internet ftp site: ftp.nectech.com CompuServe: go NECTECH America Online: keyword NECTECH World Wide Web:
ページ14に含まれる内容の要旨
Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace any part of the enclosed unit, other than the LCD backlight, which proves defective for a period of three (3) years from the date of first consumer purchase. The LCD backlight is warranted for a period of one (1) year. Spare parts are warranted for ninety (90) days. This warranty give
ページ15に含まれる内容の要旨
NEC LCD Series PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Technologies and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others. The NEC Technologies product(s) discussed in
