ページ1に含まれる内容の要旨
Marshall Electronics
QV171-HDSDI
17" Full Resolution Quad-Viewer Monitor
Operating Instructions
ページ2に含まれる内容の要旨
2
ページ3に含まれる内容の要旨
Contents Product Overview............................................................................................................................................... 5 Features................................................................................................................................................................ 5 Installation and Initial Setup ........................................................................................................................... 6 U
ページ4に含まれる内容の要旨
4
ページ5に含まれる内容の要旨
Product Overview The QUAD VIEWER Series is the latest addition to Marshall's line of IMD-equipped monitors. The monitor features a full resolution 1920 x 1200 LCD panel, built-in high quality HD Quad Splitter, four independent HDSDI inputs, one DVI-I input, IMD (In-Monitor Display) capability, Audio Presence indicator, and Time Code. Video and DVI-I both offer full screen mode, while quad-split mode is scaled to fit onscreen in the highest resolution. IMD and Tally are supported via manual mode,
ページ6に含まれる内容の要旨
Installation and Initial Setup ■ Unpacking Carefully unpack the QV171-HDSDI monitor and verify that the following items are included: • QV171-HDSDI Monitor • V-PS12-5V-1 Power Supply with 2-Pin Twist Lock Connector • Operating Instructions Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States, call +1 (310) 333-0606. ■ Inst
ページ7に含まれる内容の要旨
Top and Front Panel Features Power Button User-Definable Function Buttons Turn the monitor off or on by pressing the power Two user-definable function buttons can be used for button. In the ON state, the LED on the power direct access to various settings. Functions are button will illuminate green. assigned using the on-screen menu (See User- Definable Function Buttons – Page 15). Input Channel Buttons Pressing Ch.1, Ch.2, Ch.3, or Ch.4 will select HDSDI-SDI Video Inputs 1, 2, 3 or 4. This also
ページ8に含まれる内容の要旨
Rear Panel Features RS-422/485 Serial Interface Power Input The RS-422/485 ports are used to remotely control the IMD or all QV171-HDSDI features, using a Connect the 12VDC input to the 2-Pin twist lock variety of industry standard protocols. (Note: power input connector. Power can be supplied from Connector/pin-out may need to be adapted the included power supply, or from a variety of DC depending on protocol and controlling device sources supplying at least 3.0 Amps at 12 Volts. used. See pin-
ページ9に含まれる内容の要旨
Compatible Input Formats The following SDI standards are supported by the QV171-HDSDI: 525i, 625i 1035i/60, 1035i/59.94 1080i/60, 1080i/59.94, 1080i/50 1080psF/24, 1080psF/23.98 1080p/24, 1080p/25, 1080p/29.97, 1080p/30 720p/60, 720p/59.94, 720p/50 The following VESA standards are supported by the QV171-HDSDI (DVI-I input): 640x480 @60Hz 800x600 @60Hz 1280x1024 @60Hz 1680x1050 @60Hz 1600x1200 @60Hz The following DVI-Video standards are supported by the QV171-HDSDI (DVI input): 525i, 625i 480p/59
ページ10に含まれる内容の要旨
Quad Mode and Layouts (Continued) Ch.2 IMD Text Ch.1 Ch.3 IMD Text 00:00:00:00 Ch.4 IMD Text IMD Text Quad Layout #2 Ch.1 00:00:00:00 IMD Text Ch.3 Ch.4 Ch.2 IMD Text IMD Text IMD Text Quad Layout #3 10
ページ11に含まれる内容の要旨
On-Screen Menu STRUCTURE OVERVIEW Back Return to Main Menu Monochrome Link All Off, On Blue Only Link All Off, On Pixel to Pixel Link All Off, On Video Config Aspect Ratio Link All Full, 4:3, Scaled 4:3, 16:9 Curtain Color Link All Blue, Red, Green, White, Black Ctemp/Gamma 55k, 65k, 93k, Linear Framelock Preference Ch1, Ch2, Ch3, Ch4, Freerun Analog Phase 0-31 (DVI-Analog input only) Back Return to Main Menu Monochrome, IMD State, Anc. Timecode, OSD Tally, Audio Monitor, CC Function 1 Monitor,
ページ12に含まれる内容の要旨
On-Screen Menu (continued) MAIN MENU AND NAVIGATION Access and navigate the main menu using the RotoMenu ™ knob: Main Menu Using the RotoMenu knob • Press the RotoMenu ™ knob to enter the main menu. • Rotate the knob to scroll up or down in the main menu or each submenu. • Press the RotoMenu ™ knob to enter a submenu or choose a setting. • To return to main menu from submenu, select ‘Back’ and press the RotoMenu ™. The menu automatically times out after 15 seconds of being idle. VIDEO CONFIGURAT
ページ13に含まれる内容の要旨
On-Screen Menu (continued) VIDEO CONFIGURATION SUBMENU (continued) ■ Monochrome Mode Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale picture. ■ Blue-Only Mode Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching off the red and green components. Use this mode when calibrating the monitor to SMPTE color bars with the following procedure: 1. Allow the monitor to warm up for a
ページ14に含まれる内容の要旨
On-Screen Menu (continued) VIDEO CONFIGURATION SUBMENU (continued) ■ Aspect Ratio Settings Use this menu option to switch between several aspect ratio settings. As the QV171-HDSDI monitor has a native resolution of 1920x1200 RGB pixels, incoming images are automatically scaled to fit the screen: • In 4:3 mode, images are scaled up or down to fill the maximum 4:3 portion of the screen (1600 x 1200). IMD text and time code are superimposed on the lower portion of the image. The audio presence indi
ページ15に含まれる内容の要旨
On-Screen Menu (continued) VIDEO CONFIGURATION SUBMENU (continued) ■ Curtain Color Use this setting to choose the default color displayed on the screen when no video input is present. Available colors are blue, red, green, white, and black. ■ Ctemp/Gamma Use this setting to choose one of three color temperature / gamma presets: • D55 (5500K) • D65 (6500K) • D93 (9300K) • Linear (No gamma applied) ■ Framelock Preference Used to designate one of the inputs as a reference for synchronizing image sc
ページ16に含まれる内容の要旨
On-Screen Menu (continued) SYSTEM CONFIGURATION SUBMENU Use the System Configuration submenu to control various system parameters. System Configuration Submenu ■ User-Definable Function Buttons Use the Function 1 and Function 2 menu items to define each function button on the front panel of the monitor. The following options are available for each button: • IMD Display/hide IMD text • Time Code Display/hide time code • OSD Tally Rotate amongst types of OSD Tally • Audio Monitor Display/hide audi
ページ17に含まれる内容の要旨
On-Screen Menu (continued) SYSTEM CONFIGURATION SUBMENU (continued) ■ Saving and Loading User Presets Use the SAVE CONFIG and LOAD CONFIG menus to save current settings to one of 6 presets, or load a preset. Each Preset saves all monitor settings except for IMD configuration. • Use the LOAD CONFIG menu to load one of presets USR1 – USR6. Factory default settings can also be loaded by selecting MFG. (Factory defaults cannot be overwritten.) • Use the SAVE CONFIG menu to save the current settings
ページ18に含まれる内容の要旨
On-Screen Menu (continued) OSD CONFIGURATION SUBMENU (continued) ■ Status Display Use this setting to enable or disable status display. When enabled, the current video input standard is displayed on the top left of the screen. When disabled, status is only displayed for 2 seconds when the monitor is powered on, when an input is applied, or when the input video standard changes. The status display reads “No Input” when no video input is present. Status Display ■ Time Code Use this setting to enab
ページ19に含まれる内容の要旨
On-Screen Menu (continued) OSD CONFIGURATION SUBMENU (continued) ■ OSD Tally Use this setting to choose how tally is displayed on the screen. The available OSD Tally options depend on the Tally Source selected in the IMD Configuration submenu (see page 22). When the Tally Source is set to Standard (contact closure), OSD Tally can be set to Off, RGY, RG, or GR: • Off On-screen tally is disabled • RGY Red, yellow, or green tally signals are indicated at both the bottom left and bottom right corner
ページ20に含まれる内容の要旨
On-Screen Menu (continued) OSD CONFIGURATION SUBMENU (continued) ■ Audio Monitor Use the Audio Monitor menu option to enable or disable the audio presence indicator icon. When enabled, this icon indicates whether embedded audio is present in the SDI video input. A red circle and cross will flash on the icon if no embedded audio is present. Embedded Audio Present No Embedded Audio ■ CC Monitor (Closed Captioning) Use the CC Monitor menu option to enable or disable the Closed Captioning presence i
