ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
User Guide Elo Entuitive 2125C Desktop Touchmonitor Revision A P/N 008544 ET2125C Series Models Elo TouchSystems, Inc. 1-800-ELO-TOUCH www.elotouch.com
ページ3に含まれる内容の要旨
Copyright © 2001 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permis- sion of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes n
ページ4に含まれる内容の要旨
iv
ページ5に含まれる内容の要旨
Table of Contents Chapter 1 Appendix C Introduction 1 Technical Specifications 27 Precautions . . . . . . . . . . . . . . . . . . . . 1 Touchmonitor Specifications . . . . . . . . . . 27 About the Product . . . . . . . . . . . . . . . . . 1 21" CRT Touchmonitor Dimensions . . . . . 31 Signal PINOUT for 21" Monitor . . . . . . . 33 Chapter 2 Power Consumption. . . . . . . . . . . . . . . 34 Preset Timing Table . . . . .
ページ6に含まれる内容の要旨
Copyright © 1996, Borland International. All rights reserved. BORLAND CONFIDENTIAL September 21, 2001 9:10 am (D:\Vera new\8544-21 inch Hyundai CRT UG\21inch Hyundai CRTTOC.fm) vi
ページ7に含まれる内容の要旨
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new high-resolution touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in CRT display design. This combination of features creates a natural flow of information between a user and the touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your
ページ8に含まれる内容の要旨
1-2 Elo Entuitive Tou chmon ito r User Guide
ページ9に含まれる内容の要旨
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to install your CRT touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 9 items are present and in good condition: Quick Installation Guide CD Software User's Guide User’s Guide, Quick Install Guide, and TouchTools CD-ROM CRT Touchmonitor European power cable Monitor power cable (US/Canada) Serial touchscreen cable Video cable Base 2-3
ページ10に含まれる内容の要旨
Getting Started Installing the Base Carefully turn the touchmonitor upside-down. Place the base against the bottom of the monitor so that the base fasteners are aligned with appropriate slots. Push the base towards the front of the monitor until the latch locks into position. Carefully turn the touchmonitor right-side up. Selecting a Suitable Location Place the monitor at least 12 inches from other electrical or heat-emitting equipment and allow at least 4 inches on each side for ve
ページ11に含まれる内容の要旨
Connecting Your Touchmonitor Your touchmonitor comes with a Serial (RS-232) touchscreen connector cable. IMPORTANT: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. Video cable 1 Connect one end of the video cable to the video connector on your PC and the other end of the cable to the video connector on your monitor. Secure the cable by turning the screws on the connector. 2-5
ページ12に含まれる内容の要旨
Power cable Video cable 2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord into a surge protector, and then connect the surge protector to a grounded (three-pronged) AC electrical outlet. 2-6 Elo Entuitive Tou chmon ito r User Guide
ページ13に含まれる内容の要旨
Video cable Power cable Touchscreen cable 3 Connect the touchscreen cable. Connect one end to the appropriate port on the back of your PC. Connect the other end of the cable to the touchscreen connector on your touchmonitor. The touchscreen cable connectors should fit snugly into the connectors on your touchmonitor and PC. 2-7
ページ14に含まれる内容の要旨
Power LED Soft Power Switch 4 Power on your monitor using the Soft power switch and check that the power LED is on, then power on your PC. If not, repeat steps 2, 3, and 4, or refer to Chapter 4, Troubleshooting. 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls according to your personal preference (see Chapter 3). 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate touchscreen driver software. Follow the
ページ15に含まれる内容の要旨
Your Elo touchmonitor is plug-and-play compliant. Information on the video capabilities of your touchmonitor is sent to your video display adapter when Windows starts. If Windows detects your touchmonitor, follow the instructions on the screen to install a generic plug-and-play monitor. Refer to the appropriate following section for driver installation instructions. Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have admin
ページ16に含まれる内容の要旨
4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected, choose Next again. 5 You will see several files being copied. Insert your Windows 98 CD if prompted. Choose Finish. If Windows 98, Windows Me or Windows 2000 does not start the Add New Hardware Wizard: NOTE For Windows 2000 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2 If the AutoStart feature for your CD-ROM drive is active, the sys
ページ17に含まれる内容の要旨
C H A P TER 3 C HAP TER 3OPERATION About Touchmonitor Adjustments By design, your Elo Entuitive touchmonitor should not require any adjustments. The factory settings will give you optimum video results with most standard PC video display adapters. However, after connecting your touchmonitor you can further optimize the settings to meet your requirements by following the directions in this chapter. All adjustments you make to the controls are automatically memorized, so you do not need to res
ページ18に含まれる内容の要旨
Touchmonitor Controls You can adjust the screen display by using the buttons located below the screen. Using the On Screen Display (OSD) 1 Push the MENU button to access the OSD. The resolution and frequency are displayed at the top of the menu for your information. 2 Push the or button to choose the item you want to adjust. The selected item is highlighted. 3 Push the SELECT button to adjust the highlighted item. 4 Push the or button to adjust the selection. 5 Push
ページ19に含まれる内容の要旨
Brightness Use the button to select the brightness adjustment. Adjust with or button. Contrast Use the button to select the brightness adjustment. Adjust with or button. Locking/Unlocking the OSD Functions You are able to lock the OSD functions if you do not want them to be changed. To lock the OSD functions: 1 Press the power button to turn the monitor off. 2 Press the power button on and press the Menu key for 2 or 3 seconds or until you see the green LED on the power button. The factory
ページ20に含まれる内容の要旨
OSD Adjustments H. Size Adjusts the horizontal size of the entire screen image. Adjusts the horizontal position of the entire screen image. H. Position V. Size Adjusts the vertical size of the entire screen image. V. Position Adjusts the vertical position of the entire screen image. If the vertical sides of the picture curve in or bulge out, you can Pincushion correct the distortion by using the pincushion adjustment. If the picture is wider at the top or at the bottom, you can Trapezoid corre
