ページ1に含まれる内容の要旨
TFT-LCD VIDEO MONITOR
TFT-LCD SECURITY MONITOR
USER MANUAL
V151HV/ V172SV/ V191HV Video Series
and V151BN/ V172BN/ V191BN Security Series
www.viewera.com
R3.0
ページ2に含まれる内容の要旨
Table of Contents EMC Compliance … … … … … … … ..… … … … … … … … … … … … … … … … … … … … … .… … ....2 Important Precautions ............................................................................................................3 1. Introduction 1.1 General … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … ..4 1.2 Features … … … … … … … … … … … … … … … … ..… … … … … … … … … … … … … … … … … ..4 1.3 Package contents .… … … … … … … … … … … … … … … … … … … … … … … … … … ..… … …
ページ3に含まれる内容の要旨
EMC COMPLIANCE This device has been tested and found to comply with the standards for a class B digital device, pursuant to Part 15 of FCC Rules. Those standards are designed to provide reasonable protection against harmful interference in a residential installation. This device generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this device does cause harmful interfere
ページ4に含まれる内容の要旨
IMPORTANT PRECAUTIONS 1. Before using this device, please read all the instructions in this manual carefully. 2. Please keep the manual carefully for future reference. 3. Unplug this device from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp or wet cloth to clean. Please use LCD screen detergent for cleaning if it is still dirty. 4. Do not use the parts not recommended by the manufacturer, otherwise it may cause a hazard. 5. When unplugging the powe
ページ5に含まれる内容の要旨
Introduction General Thank you for purchasing ViewEra’s LCD monitor which incorporates high quality display, multiple video inputs, and power-saving energy management into a light-weighted LCD monitor. The LCD video monitor uses color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance. Features TFT LCD panel Composite video input/ output (for security monitor series), VGA input, and composite audio inputs. Built-in speakers with volum
ページ6に含まれる内容の要旨
2. Installation The monitor is equipped with an automatic sensing AC power adapter for a voltage range from 100 to 240 VAC at a frequency of 50 to 60 Hz. Before connecting the cables, please make sure that the monitor and the computer power are both turned off. Please follow the steps to install your monitor. a. Security Monitor Rear Panel b. Video Monitor Rear Panel 2.1 Connecting the signal cable Plug one end of the VGA cable or video cable to a computer or a video device and the
ページ7に含まれる内容の要旨
2.5 Power on Turn on your monitor and computer. The LED indicator will light green when the screen is under normal condition. If the LED indicator lights amber, please check if the signal cable is securely connected between the computer and the monitor. 2.6 Choosing the optimal resolution for computer 1) Double click the Display icon in the Control Panel. 2) Select “Settings” tab from the Display Properties window. You can change the display resolution by using the slider. 3) Select a resolut
ページ8に含まれる内容の要旨
3. User Controls 3.1 Control buttons (c) (d) (e) (f) (a), (b) a.) Power button It is used to turn on or off monitor. b) Power indicator When the monitor is under normal working condition, the indicator will light green; if the monitor is under power saving mode or has no signal input, the indicator will light amber. The indicator will turn off under the power off mode. When the power indicator turns off, it means that the monitor is under off mode, but the power adapter is still in ch
ページ9に含まれる内容の要旨
3.2 OSD menu in VGA mode Press “1” button to enter the OSD main menu. See the Figure as below. Press “1” then press UP or DOWN to move the highlight to the desired item and then press “1” button to enter. Press “ ” or DOWN to adjust the value ^ of selected item and then press “1” button for confirmation. 1) Contrast a. Press UP or DOWN to move the highlight to Contrast and press “1” to enter. 8
ページ10に含まれる内容の要旨
b. Press UP or DOWN to increase or decrease the contrast of the display. Then press “1” to confirm the adjustment and back to OSD main menu. 2) Brightness a. Press UP or DOWN to move the highlight to Brightness and press “1” to enter. b. Press UP or DOWN to increase or decrease the brightness of the display. Press “1” to confirm the adjustment and back to OSD main menu. 9
ページ11に含まれる内容の要旨
3) Sharpness a. Press UP or DOWN to move the highlight to Sharpness and press “1” to enter. b. Press UP or DOWN to increase or decrease the sharpness of the display. Press “1” to confirm the adjustment and back to OSD main menu. 10
ページ12に含まれる内容の要旨
4) Color Temperature a. Press UP or DOWN to move the highlight to Color Temperature and press “1” to enter. b. Press “1” to select preset color temperature settings, like Cool, Natural, Warm, or select User to adjust Red, Green, Blue independently. If Cool, Natural, or Warm is selected, then press “2” to confirm the selection and press “2” to exit. 11
ページ13に含まれる内容の要旨
5) User RGB If User is selected, press UP or DOWN to move the highlight to Red, and then press “1” to enter the adjustment of Red, which is done by pressing UP or DOWN. Press “1” once to confirm the adjustment of Red and move the highlight to Green and press “1” to enter the adjustment of Green. Press “1” once to confirm the adjustment of Green and move the highlight to Blue. Press “1” to enter the adjustment the of Blue and press “1” once to confirm the adjustment of Blue and exit to Color
ページ14に含まれる内容の要旨
6) Image Press “1” to get the OSD, press “1” then UP or DOWN to move the highlight to Image menu, and then press “1” to enter Image sub-menu. Then press UP or DOWN to move the highlight to Auto Tune, H Position, V Position, Phase or Clocks. 6.1) Auto Tune: Press UP or DOWN to move the highlight to Auto Tune and press “1” to automatically tune the image position, pixel clock and phase to optimum, and then press UP or DOWN to move the highlight to “Yes” and press “1” to confirm the adjustment
ページ15に含まれる内容の要旨
b. Press UP or DOWN to adjust the horizontal position. Then press “1” to confirm the adjustment and back to Image menu. 6.3) V Position a. Press UP or DOWN to move the highlight to V Position and press “1” to enter. 14
ページ16に含まれる内容の要旨
b. Press UP or DOWN to move the vertical position of OSD . Then press “1” to confirm the adjustment and back to Image menu. 6.4) Phase a. Press UP or DOWN to move the highlight to Phase and press “1” to enter. 15
ページ17に含まれる内容の要旨
b. Press UP or DOWN to adjust the phase of signal. Then press “1” to confirm the adjustment and back to Image menu. 6.5) Clocks a. Press UP or DOWN to move the highlight to Clocks and press “1” to enter. 16
ページ18に含まれる内容の要旨
b. Press UP or DOWN to adjust the clock of signal. Then press “1” to confirm the adjustment and back to Image menu. 17
ページ19に含まれる内容の要旨
3.2.1 Audio menu Press “1” to get the OSD, press UP or DOWN to move the highlight to Audio menu, and then press “1” to enter Audio adjustment, which is done by pressing UP or DOWN. 1) Volume a. Press UP or DOWN to increase or decrease the volume of the built-in speakers. Then press “1” to confirm the adjustment and back to Audio menu. 18
ページ20に含まれる内容の要旨
3.2.2 Feature Controls Press “1” to get the OSD, press UP or DOWN to select Feature Controls menu, and then press “1” to enter Feature Controls sub-menu. Then press UP or DOWN to move the highlight to Sleep Timer, Language, OSD Controls, or Factory Recall. 1) Sleep Timer a. Press UP or DOWN to move the highlight to Sleep Timer and press “1” to enter. b. Press “1” to select 10, 20, 30, 40, 50, 60, 70, 80, or 90 minutes. Default is set to Off. 2) Language menu Press UP or DOWN to move the
