ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
ViewSonic i CD5233
ページ3に含まれる内容の要旨
ViewSonic 1 CD5233
ページ4に含まれる内容の要旨
CONTENTS ——————————————————————————————————————————————— SAFETY INSTRUCTIONS...............................................................................................................3 Package Contents..........................................................................................................................9 Parts Name and Functions..........................................................................................................10 Control Panel........
ページ5に含まれる内容の要旨
SAFETY INSTRUCTIONS WARNINGS AND PRECAUTIONS KNOW THESE SAFETY SYMBOLS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this pro
ページ6に含まれる内容の要旨
REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declare under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN6100-3-2: 2006 (Limits for Harmonic Current Emission) • EN6100-3-3:19
ページ7に含まれる内容の要旨
POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the
ページ8に含まれる内容の要旨
INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains plug
ページ9に含まれる内容の要旨
中国电子信息产品污染控制标识要求(中国RoHS法规标示要求)产品中有毒有害物质或 元素的名称及含量 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr 6+) (PBB) (PBDE) 外壳 ○ ○ ○ ○ ○ ○ × × 液晶面板 ○ ○ ○ ○ × ○ ○ ○ ○ ○ 电路板组件 附件 ○ ○ ○ ○ ○ × (遥控器、电源线、连接线) × 遥控器电池 ○ ○ ○ ○ ○ ○： 表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006标准规定的限量要求 以下。 ×： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限 量要求。 环保使用期限 此标识指期限(十年)，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外 泄或突变，电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、财产造成 严重损害的期限。
ページ10に含まれる内容の要旨
NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, M
ページ11に含まれる内容の要旨
Package Contents The LCD monitor pack* should include: • Main switch cover • LCD monitor • Screw for Main Switch cover x2 • Power cord (1.8 m) • Clamper x 2 • VGA Signal Cable (1.8 m) • Screw for Clamper x 2 • CD User Manual & QSG • Remote Control and AAA Batteries Xxxxxxxxxxxx xx xxxxxxxxxxxx xxxxxxxxxxxx xxxxxxxxx CD User Manual & QSG Screw for Main switch cover (M3 x 5) x 2 Main switch cover Remote Control and AAA Batteries * The supplied power cor
ページ12に含まれる内容の要旨
Parts Name and Functions Control Panel POWER button ( ) : To switch the power on/off. MUTE button : To switch the audio mute ON/OFF. SOURCE button : To set the function while OSD menu is on or to activate input selection menu while OSD menu is off. PLUS (+) button : To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off. MINUS (-) button : To decrease the adjustment while OSD m
ページ13に含まれる内容の要旨
Terminal Panel EXTERNAL CONTROL (mini D-Sub 9 pin) This is for serial connection when multiple monitors are connected. To achieve remote management through RS232 commands (refer to the RS232 remote control user manual), connect the RS-232C OUT connector from a computer or from a different monitor to the RS-232C IN connector from your monitor. The same RS-232C commands can be looped through by connecting the RS-232C OUT of this monitor to the next RS-232C IN.
ページ14に含まれる内容の要旨
Remote Control MENU button To turn the OSD menu on/off. DOWN button To move the highlight bar down to adjust the selected item when OSD menu is on. To move the sub-picture down when in “PIP” mode. INFO. button To turn on/off the setting information displayed on the right-up corner of the screen. SIZE button To select the picture size from [FULL], [NORMAL], [CUSTOM] , [DYNAM IC] and [REAL]. VOLUME button VOL＋ button: To incre
ページ15に含まれる内容の要旨
Operating Range for the Remote Handling the remote control Control * Do not subject to strong shock. * Do not allow water or other liquid to splash the remote Point the top of the remote control towards the LCD monitor's remote control. If the remote control gets wet, wipe it dry sensor during button operation. immediately. Use the remote control within a distance of about 7 m/ 23 ft from the * Avoid exposure to heat and steam. front of the LCD monitor's remote control sensor and within
ページ16に含まれる内容の要旨
Setup Procedure 3. Connect to external equipment 1. Install the system on the right location • To protect the connected equipment, turn off the main power CAUTION: before making connections. THE LCD MONITOR MUST BE MOVED OR INSTALLED BY • Please refer to section “Connectivity” P.18~P.22 for operations. TWO OR MORE PERSONS. Failure to follow this caution may result in injury and damage when the LCD monitor falls. 4. Connect power cord • The power outlet socket should be inst
ページ17に含まれる内容の要旨
9. Adjust the image Make adjustments to brightness or contrast if required. 10. Recommended Adjustment To reduce the risk of “image persistence”, please adjust the following items based on the application being used. “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”. 11. To prevent the main power switch from being changed To prevent the possibility of main power switch being carelessly pushed, please attach the main switch cover (accessory) onto it. NOTE: With the main power switch co
ページ18に含まれる内容の要旨
How to Mount and Attach Feet to the LCD Monitor You can install the LCD monitor in one of the following two ways: Method 1: Attach and remove the optional stands How to install stands 1. Please turn the monitor off. 2. After inserting stand in guide block, fasten the thumbscrews on both sides of the monitor. NOTE: Install the table stand with the longer end of the feet directing to the front. In the upright position
ページ19に含まれる内容の要旨
To avoid monitor from falling Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and damage. As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor( approx. 47.5 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are recommended. Screw he
ページ20に含まれる内容の要旨
Ventilation Requirements for enclosure locating To allow heat to disperse, leave space between surrounding objects as shown in the diagram below. ViewSonic 18 CD5233
