ページ1に含まれる内容の要旨
Touchcomputer User Guide
1520 15-inch LCD Multifunction Touchcomputer
ページ2に含まれる内容の要旨
Elo TouchSystems Touchcomputer User Guide 15" LCD Multifunction Touchcomputer 1520 Revision A P/N E439739 Elo TouchSystems 1-800-ELOTOUCH (1-800-356-8682) www.elotouch.com
ページ3に含まれる内容の要旨
Copyright © 2009 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no re
ページ4に含まれる内容の要旨
Table of Contents Setup 5 Desktop 22 Unpacking Your Touchcomputer 5 Maintenance 23 Product Overview 6 Care and Handling 23 Front View 6 Warning 24 Rear View 6 Waste Electrical and Electronic Equip- Side View 7 ment (WEEE) Directive 24 Base Bottom View 7 Technical Specifications 25 Display Orientation 8 Touchcomputer Specifications 25 Initial Connections 9 Dimensional Diagrams 25 Standard Unit: 9 Front 25 Advanced Unit: 9 VESA 26 Initial Power-On 10 Rear 26 Language Selection 10 Base Mounting 27
ページ5に含まれる内容の要旨
C H A P T E R 1 Setup This chapter discusses how to set up and test your Touchcomputer and any included peripheral options. Unpacking Your Touchcomputer Check that the following items are present and in good condition: OR Touchcomputer Power cable US/Canadian European power cable Quick Install Guide & CD/DVD Power Adapter Elo TouchSystems 1520 User Guide 5
ページ6に含まれる内容の要旨
Product Overview Front View Rear View Elo TouchSystems 1520 User Guide 6
ページ7に含まれる内容の要旨
Side View Base Bottom View Elo TouchSystems 1520 User Guide 7
ページ8に含まれる内容の要旨
Display Orientation Elo TouchSystems 1520 User Guide 8
ページ9に含まれる内容の要旨
Initial Connections Prior to turning on your Touchcomputer you must take the power adapter and appropri- ate power cable from the accessories box. Plug the small round plug with four pins into the 12Vdc power input on the Touchcomputer. Plug the power cable into the power adapter and the other end into a suitable power outlet (mains). Make sure the audio jumper cable and video jumper cable are in place as shown below. Standard Unit: Intel: Integrated Dual-core Intel® Atom™ 1.6 GHz processor
ページ10に含まれる内容の要旨
Initial Power-On The initial setup of the operating system takes approximately 5-10 minutes. Additional time may be needed depending on touchcomputer hardware configuration and con- nected devices. To setup the Windows Operating System (OS) for the touchcomputer, turn on the touchcomputer and follow the instructions on the screen. Language Selection When the following window appears, you have the option of changing the language used in menus and dialogs. Click Customize. The Regional and Languag
ページ11に含まれる内容の要旨
Time-zone selection When the following window appears, you may change the time-zone, date, and/or time of the touchcomputer. After making any changes, click Next to finish. Windows Setup will complete the initialization of the touchcomputer. Test Devices Testing the Touchscreen The touchscreen is pre-calibrated for accurate touch response. Elo TouchSystems 1520 User Guide 11
ページ12に含まれる内容の要旨
Calibration* If for any reason the touchscreen needs to be re-calibrated, go to the control panel and double-click the Elo Touchscreen icon. The window shown below will open. Click on the Align button. This launches the align/calibration program. A window similar to the one shown below will open. Follow the instructions to align/calibrate the touchscreen. *The alignment/calibration procedure may vary between touch technologies. Elo TouchSystems 1520 User Guide 12
ページ13に含まれる内容の要旨
C H A P T E R 2 Operation This chapter shows the user how to: control the On-Screen Display (OSD) and Power buttons, use the I/O panel, securely mount the Touchcomputer and adjust the display head. MENU UP / INCREASE DOWN / DECREASE SELECT POWER Elo TouchSystems 1520 User Guide 13
ページ14に含まれる内容の要旨
Side Panel Controls All adjustments made to the display via OSD and Power controls are automatically saved. User settings will remain unchanged after powering off/on or in the case of a power failure. Control Function 1 Menu/Exit Opens On Screen Display (OSD) / Exits the OSD menu. 2 Up 1. Enter contrast adjustment. 2. Increase value of the selected item. 3. Move OSD selection clockwise. 3 Down 1. Enter brightness adjustment. 2. Decrease value of the adjustment item. 3. Move OSD selecti
ページ15に含まれる内容の要旨
The OSD provides the following adjustments: Brightness Adjusts the background luminance of the LCD panel. Contrast Adjusts the contrast or the values of color gain (RED, GREEN or BLUE). Color Temperature • sRGB mode can be selected. • Sets color temperature values of 5500, 6500, 7500,9300 and user defined. OSD Time-out Adjusts the time the OSD remains on the screen after no activity OSD Vertical Position Adjusts the OSD position up or down. OSD Horizontal Position Adjusts the OSD position lef
ページ16に含まれる内容の要旨
OSD Lockout The On Screen Display (OSD) feature can be locked out (disabled) if desired. To enable this feature, when the OSD is not present, simultaneously press the UP and Down buttons until OSD LOCKED appears on the screen (approximately five seconds). To re- enable the OSD function again, simultaneously press the UP and Down buttons until OSD UNLOCKED appears on the screen (approximately five seconds). Headphone Jack Elo TouchSystems 1520 User Guide 16
ページ17に含まれる内容の要旨
Power Control Power Button The power button function can be set by the operating system under: Control Panel->Display Properties->Screen Saver->Power->Advanced->Power Buttons. To override all Operating System settings and shut down the Touchcomputer, press and hold the power button for 4-5 seconds. Note: On select models the delay to override the operating system is extended to 15 seconds. Elo TouchSystems 1520 User Guide 17
ページ18に含まれる内容の要旨
Using the I/O panel The Touchcomputer provides the following I/O interfaces for connecting a wide vari- ety of compliant devices. Standard Unit: Intel® Desktop Board D945GCLF2 VGA There is one VGA (HD-15) port (normally connected with supplied jumper cable to display VGA input). USB There are four USB 2.0 type A ports. Ethernet There is one RJ45 Ethernet port providing LAN capabilities. Serial There is one RS232 serial port. Microphone Input There is one 3.5 mm microphone input jack for connecti
ページ19に含まれる内容の要旨
Advanced Unit: Intel® Desktop Board DQ45EK USB and Powered USB There are six USB 2.0 type A ports. eSATA One external SATA (eSATA) channel is provided. Ethernet There is one RJ45 Ethernet port providing LAN capabilities. Serial There is one RS232 serial port . Microphone Input There is one 3.5 mm microphone input jack for connecting an external microphone. Audio Output There is one 3.5 mm stereo audio output jack for connecting headphones, typically connected with the supplied jumper cable to t
ページ20に含まれる内容の要旨
Kensington Lock The Kensington lock is a security device that prevents theft. To find out more about this security device, look for Computer Locks on the Kensington website at: http:// www.kensington.com. Elo TouchSystems 1520 User Guide 20
