ページ1に含まれる内容の要旨
LCD MONITOR
quick start guide
460DRn 460DR
ページ2に含まれる内容の要旨
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables D-Sub Cable Power Cord Others
ページ3に含まれる内容の要旨
Introduction Others Remote Control Batteries (AAA X 2) BNC to RCA Adaptor Jack (Not available in all loca- tions) Sold separately DVI Cable Wall Mount KIT Semi Stand KIT Calibrater BNC Cable LAN Cable For more information on the use of the calibrater, see Nat- (Applicable to the DRn mod- ural Color Expert Help. el only) Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Dow
ページ4に含まれる内容の要旨
Introduction ENTER button [ENTER] Activates a highlighted menu item. SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] → [HDMI] → [MagicInfo] >> Click here to see an animation clip Note • The MagicInfo menu is available DRn model. PIP Push the PIP button to turn the PIP screen On / Off. More than one PIP cannot overlap on scr
ページ5に含まれる内容の要旨
Introduction Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the LCD Display. Rear Note For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD Display 's configuration at the back may vary slightly depending o
ページ6に含まれる内容の要旨
Introduction REMOTE OUT/IN You can use a wired remote control by connecting it to your LCD Display. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [PC/DVI/BNC AUDIO IN] (PC/DVI/BNC/HDMI Audio Connection Ter- minal (Input)) DVI / PC / HDMI IN [HDMI] Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your dig- ital output device using a HDMI cable. DVI / PC / HDMI IN [RGB](PC Video Con- nection Terminal) Using a
ページ7に含まれる内容の要旨
Introduction AV AUDIO IN [L-AUDIO-R] (LCD Display Audio Connection Terminal (Input)) AV OUT [VIDEO](VIDEO Connection Ter- minal) AV mode (Output) AV IN [VIDEO](VIDEO Connection Termi- nal) (Input) AV OUT [S-VIDEO] (S-VIDEO Connection Terminal) S-VIDEO mode (Output) AV IN [S-VIDEO](S-VIDEO Connection Terminal) (Input) EXT SPEAKER (8 Ω)[- - L - +, - - R - +] (EXT Speaker Connection Terminal) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output))AUDIO OUT is the terminal for
ページ8に含まれる内容の要旨
Introduction Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. ON / OFF MagicInfo MDC LOCK MagicInfo buttons +100 DEL VOL MUTE TTX/MIX MENU ENTER P.MODE AUTO ENTER/PRE-CH CH/P SOURCE INFO EXIT Up-Down Left-Right buttons S.MODE STILL FM RADIO P.SIZE SRS DUAL/MTS PIP SOURCE SWAP SIZE REW STOP PLAY/PAUSE
ページ9に含まれる内容の要旨
Introduction FF 1. ON / OFF Turns the LCD Display On/Off. 2. MagicInfo MagicInfo Quick Launch Button. (Applicable to the DRn model only) 3. MDC MDC Quick Launch Button. 4. LOCK Activates or deactivates all function keys on both the remote con- trol and the LCD Display except for the Power and LOCK buttons. 5. MagicInfo buttons MagicInfo Quick Launch Button. (Applicable to the DRn model only) • Alphanumeric: Used to enter the Internet address. • DEL: Functions as the backspace. • SYMBOL: Used to
ページ10に含まれる内容の要旨
Introduction watching. Then push button again to circle through available pre- configured modes. (Entertain → Internet → Text → Custom ) 13. AUTO Adjusts the screen display automatically in PC mode. By changing the resolution in the control panel, auto function is performed. Returns to the immediately previous channel. 14. ENTER/PRE-CH - This fuction does not work for this LCD Display. 15. CH/P In TV mode, selects TV channels. - This fuction does not work for this LCD Display. Changes the video
ページ11に含まれる内容の要旨
Introduction - This fuction does not work for this LCD Display. Every time you press the button, a PIP screen appears. 26. PIP Changes the source of the PIP window signal. 27. SOURCE 28. SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. Switches the PIP Picture Size. 29. SIZE 30. REW Rewind Stop 31. STOP 32. PLAY / PAUSE Play/Pause Fast forward 33. FF
ページ12に含まれる内容の要旨
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User Con- tro
ページ13に含まれる内容の要旨
Connections Using the BNC (Analog) connector on the video card. • Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V ports on the back of your LCD Display and the 15 pin D-sub Port on the computer. Connect the audio cable for your LCD Display to the audio port on the back of your computer. Note • Turn on both your computer and the LCD Display. • The DVI cable or BNC cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other de
ページ14に含まれる内容の要旨
Connections Connecting a VCR AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC cable. Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the LCD Display 's AV AUDIO IN [L-AUDIO-R] using audio cables. Note • Select AV or S-Video for a connected VCR or Camcorder using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the VCR or Camcorders with a ta
ページ15に含まれる内容の要旨
Connections Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the DVD Player with a DVD disc inserted. • A component cable is optional. • For an explanation of Component video, consult your DVD manual. Connecting a Camcorder Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks o
ページ16に含まれる内容の要旨
Connections Connecting a DTV Set Top Box Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO- R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note • Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the LCD Display or on the remote control. • For an explanation of Component vide
ページ17に含まれる内容の要旨
Connections Connecting to a Wired Remote Control Note • You can control your LCD Display by allowing it to receive the remote control signals of other devices through the REMOTE OUT terminal. • You can control a device by allowing it to receive remote control signals from other devices through the REMOTE IN terminal. • Restrictions: Available only if other devices support the wired remote control I/O terminals. Connecting Using a HDMI Cable Note • Input devices such as digital DVD are connecte
ページ18に含まれる内容の要旨
Connections Note • Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. • Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the HDMI / PC / DVI-D AUDIO IN terminal of the LCD Display. Connecting a LAN Cable Using a Power cord with Earth • In the event of failure, the earth lead may cause electric sh
ページ19に含まれる内容の要旨
Connections Note (Applicable to the DRn model only) Note You can connect USB devices such as a mouse or keyboard.
ページ20に含まれる内容の要旨
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detect
