ページ1に含まれる内容の要旨
SyncMaster 151MP / 171MP
ページ2に含まれる内容の要旨
English > Main > Index Main Page Safety Instructions Adjusting Your LCD Monitor Notational User Controls Power User control buttons Installation Direct-Access Features Cleaning On-Screen Display Other OSD Functions Introduction Screen Adjustment Animation Clips Unpacking Troubleshooting Front Check before Calling for Service Rear Problems and Solutions Remote Control Q & A Setup Specifications Connecting Your Monitor General Specifications Connecting to a Computer PowerSaver Connecting to
ページ3に含まれる内容の要旨
English > Main > Safety Instructions > Notational Notational Power Installation Cleaning Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
ページ4に含まれる内容の要旨
English > Main > Safety Instructions > Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Notational Power Do not use a damaged or loose plug. Installation This may cause an electric shock or fire. Cleaning Other Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause e
ページ5に含まれる内容の要旨
English > Main > Safety Instructions > Installation Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Notational Power Installation Cleaning Put your monitor in a location with low humidity and a minimum of dust. Other An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause i
ページ6に含まれる内容の要旨
English > Main > Safety Instructions > Cleaning When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Notational Power Do not spray detergent directly on the monitor. Installation Cleaning Other Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire. Do not set a glass of water, chemi
ページ7に含まれる内容の要旨
English > Main > Safety Instructions > Ohter Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Notational Power Installation Cleaning If your monitor does not operate normally - in particular, if there are any unusual Other sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire. Do not place
ページ8に含まれる内容の要旨
English > Main > Introduction > Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Front Rear Remote Control User's Guide and Natural Color/ Power Cord Signal Cable(15 pin D-Sub) Driver Installation CD Quick Setup Guide DC Adapter Warranty Card (Not available in all locations) Monitor TV Tuner Box (Option) Batteries (AAA X 2) Audio Cable Remote Control Scart Jack
ページ9に含まれる内容の要旨
English > Main > Introduction > Front For detail information concerning the monitor functions, refer to User Controls under Adjusting Your Monitor. The monitor's front configuration may vary slightly depending on the monitor model. Unpacking Front Rear Remote Control 1 PC mode button 6 Up-Down button / Channel button 2 PIP mode button 7 Left-Right button / Volume button 3 Video mode button 8 Menu button 4 Audio mode button 9 Exit button 5 Power button / Power indicator 10 Auto button
ページ10に含まれる内容の要旨
English > Main > Introduction > Rear For detailed information concerning cable connections, refer to Connecting Cables under Setup. The monitor's rear configuration may vary slightly depending on the monitor model. Unpacking Front Rear Remote Control A PC Connection Terminal 1 Power Connection Terminal (12V DC) 2 Computer Connection Terminal (15 Pin D-SUB) 3 Audio Connection Terminal (Audio (ST)) B AV Connection Terminal 1 AV right audio connection terminal (R) 2 AV left audio connection
ページ11に含まれる内容の要旨
English > Main > Introduction > Remote Control For detailed information of the Remote Control Unit functions, refer to Adjusting Your Monitor > User Controls > User Control Buttons > Remote Control buttons. The remote control's configuration may vary slightly depending on the monitor model. The Remote control may function within a range of 0.23 to 33 feet (7cm to 10m) and 30 degrees to the left and right of the monitor's Remote Control Reception sensor. Unpacking Front Button Names | Re
ページ12に含まれる内容の要旨
English > Main > Setup > Connecting Your Monitor > Connecting to a Computer Connecting to a Computer Connecting to other devices Turn on your computer and monitor. If your monitor displays an image, installation is complete. Connecting Your Monitor Installing the 1. Connecting to a Computer Monitor Driver Installing a VESA base 1. Connect the power cord to the DC adapter and connect the adapter jack to the DC12V power port on the back of your monitor. 2. Connect the signal cable to
ページ13に含まれる内容の要旨
English > Main > Setup > Connecting Your Monitor > Connecting to other devices Connecting to a Computer Connecting to other devices AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to the monitor. Connecting Your For detailed information on connecting AV input devices, refer to User Controls under Adjusting Your Monitor. Monitor Installing the Connecting AV Devices | Connecting TV | Connecting to a Macintosh | Connecting Headphone Monitor Driver
ページ14に含まれる内容の要旨
1. Connect the antenna or the cable box to the TV tuner box (not included) using the "ANTENNA" terminal on the tuner box. 2. Remove the TV Tuner Box cover from the rear of the monitor. 3. Insert the connected tuner box into the slot and firmly tighten the two screws using a coin to lock the box in place. (Loose screws may cause a blank screen or picture noise) 4. Replace the TV Tuner Box cover. 5. Turn on the monitor. 6. Select TV using Source button among the external signal adjustment button
ページ15に含まれる内容の要旨
4. Connecting Headphone You may connect your headphones to the monitor. 1. Connect your headphones to the Headphone-out port.
ページ16に含まれる内容の要旨
English > Main > Setup > Installing the Monitor Driver > Automatic Automatic Manual When prompted by the operating system for the monitor driver, insert the CD-ROM included with this Connecting Your monitor. Driver installation is slightly different from one operating system to another. Follow the Monitor directions as appropriate for the operating system you have. Installing the Monitor Driver Prepare a blank disk and download the driver program file at the Internet web site shown h
ページ17に含まれる内容の要旨
1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button. 4. Click the "Install" button in the "Warning" window. 5. If you can see following Message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system. The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-mon
ページ18に含まれる内容の要旨
English > Main > Setup > Installing the Monitor Driver > Manual Automatic Manual When prompted by the operating system for the monitor driver, insert the CD-ROM included with this Connecting Your monitor. Driver installation is slightly different from one operating system to another. Follow the Monitor directions as appropriate for the operating system you have. Installing the Monitor Driver Prepare a blank disk and download the driver program file at the Internet web site shown her
ページ19に含まれる内容の要旨
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installat
ページ20に含まれる内容の要旨
10. Monitor driver installation is completed. ® ® 2. Microsoft Windows 2000 Operating System * When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. * How to install 1. Click "Start" , "Setting" , "Control Panel". 2. Double click the "Display" Icon. 3. Choose the "Set
