ページ1に含まれる内容の要旨
PLTV165
OWNER'S MANUAL
Mobile Video System
Vertical Adjustable And Horizontal Rotatable Panel
TFT Monitor With TV Tuner
Remote Control
www.pyleaudio.com
ページ2に含まれる内容の要旨
CONTENTS Important Safety Instruction ....................................................... 3 Installation .................................................................................... 4 DIN Front-Mount (Method A) ......................................................... 4 4 Installing the unit ......................................................................... Removing the unit ....................................................................... 5 DIN Rear-Mount (Metho
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTION CAUTION: Please read and observe all warnings and instructions given in this owner's manual. Keep these instructions. Retain this booklet for future reference. Please read the following safety instructions carefully. 1.This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following procedures
ページ4に含まれる内容の要旨
INSTALLATION TAKE OUT SCREW BEFORE Notes: INSTALLATION Choose the mounting location where Before install the unit, please remove the unit will not interfere with the the two screws on the back of the unit. normal driving function of the driver. Take out screw Before finally installing the unit, before installation. connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure
ページ5に含まれる内容の要旨
INSTALLATION (Tapping Screw (5x25mm) and Plain Sleeve Washer) to attach the other end of L Key Outer Trim Ring metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. R Key Hex Nut Spring Washer Metal Strap 5. Mount the sleeve by inserting the Mounting Bolt sleeve into the opening of the Plain Washer dashboard and bend open the tabs Tapping Screw located around the sleeve with a screwdriver. Not all tab
ページ6に含まれる内容の要旨
INSTALLATION DIN REAR-MOUNT (Method B) 3 1 2 4 5 1. Factory radio mounting bracket 2. Car radio mounting bracket 3. Screw 4. After aligning the car radio mounting bracket with the factory radio mounting bracket, tighten the screws (5x5mm) at 2 places on each side. 5. When fix the factory radio mounting bracket with the screws, use s standard-tipped screwdriver to open the tabs of the car radio mounting bracket to make them fit into theholes in the factory radio mounting bracket.
ページ7に含まれる内容の要旨
ELECTRICAL CONNECTION DC IN AV INPUT AV OUT TV ANT REMOTE To Diversity Antenna RGB SYSTEM 7 YELLOW VIDEO 2 IN WHITE AUDIO 2 L IN RED AUDIO 2 R IN YELLOW REMOTE CONTROL RECEIVER VIDEO OUT WHITE AUDIO L OUT RED AUDIO R OUT ACC (RED) GND (BLACK) 3A MEMORY BACK-UP (YELLOW)
ページ8に含まれる内容の要旨
OPERATION LOCATION AND FUNCTION OF KEYS 7 1 2 3 4 5 6 9 8 10 11 12 13 1 5 1 6 1 4 8
ページ9に含まれる内容の要旨
OPERATION LOCATION AND FUNCTION OF KEYS 18 17 19 21 2 0 22 2 3 2 6 2 8 24 29 27 30 25 1. /I POWER 17. POWER 2. OPEN/CLOSE 18. OPEN/CLOSE 3. IR 19. TV/AV 4. AUDIO IN (AV1) 20. 0~9 Numeric buttons 5. VIDEO IN (AV1) 21. ANGLE+ 6. 6.5 inch MULTI COLOR TFT 22. ANGLE- MONITOR 23. AUTO 7. Reset 24. VOLUME ^ ^ 8. VOLUME 25. VOLUME 9. VOLUME 26. CHANNEL ^ ^ 10. MENU 27. CHANNEL 11. TV/AV 28. -/-- 12. AUTO 29. DSP 13. IR 30. MENU 14. CHANNEL 15. CHANNEL 16. 4:3/16:9 Selector 9
ページ10に含まれる内容の要旨
OPERATION SWITCHING ON/OFF THE UNIT Switch on the unit by pressing POWER button (1) on the front panel or POWER button (17) on the remote control. When system is on, press it again to turn the unit off. OPEN/CLOSE THE MONITOR AND Fig.3 ANGLE ADJUSTMENT Return the monitor to the central Press OPEN/CLOSE button (2) on the viewing position, then press front panel or point the remote control OPEN/CLOSE button (2) on the to IR (3) on the front panel and press f
ページ11に含まれる内容の要旨
OPERATION Press CHANNEL button (15) or Notes: CHANNEL (27) button on The external remote receiver is placed remote control to choose channel near the monitor for the best to receiver downward. remote signal easily. The numeric buttons (0,1~9) (20) If the angle of the monitor from vertical allow you to select the 0 corresponding channel directly. exceeds 20 (Especially the distance exceeds 3m.), controlling the TV Press digital select button (-/--) () through IR (3) or (13) cannot g
ページ12に含まれる内容の要旨
OPERATION Auto Searching channels Press AUTO button (12) on the monitor panel or AUTO button (23) on the remote control to enter into auto searching mode, then press CHANNEL button (14) on the monitor panel or CHANNEL button ^ (26) on remote control t to start searching TV channels. Then press CHANNEL button (15) on the monitor panel for about one seconds ^ or press CHANNEL button (27) on the remote control to stop searching. Volume adjustment Press VOLUME / buttons
ページ13に含まれる内容の要旨
www.pyleaudio.com 88-T1990-02
