ページ1に含まれる内容の要旨
PT1710MX
Touchscreen LCD Monitors
USER’S GUIDE
www.planar.com
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Important Recycle Instruction: LCD Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. . Revision Date Description A April 2007 Document number 020-0555-0
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
1 Table of Contents Usage Notice Precautions .........................................................................................2 Introduction About Planar’s PT1710MX..................................................................3 Touch Screen for PT1710MX……………………………………………..4 Package Overview ..............................................................................5 Installation Product Overview.................................................................
ページ6に含まれる内容の要旨
2 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass c
ページ7に含まれる内容の要旨
3 Introduction About Planar’s PT1710MX The PT1710MX is a 17” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct Analog signal input Active matrix TFT LCD technology 1280x1024 SXGA resolution 17” viewable display area 31.5 ~ 80 kHz horizontal scan 56 ~ 75 Hz high refresh rate 0.264mm x 0.264mm Pixel pitch Auto adjustment function Multilingual OSD user controls VESA DPMS power saving Kensington
ページ8に含まれる内容の要旨
4 Touch Screen for PT1710MX Gunze analog 5-wire resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: Dual RS-232 Serial/USB controller Durability: 35 million touches at a single point Hardness of surface: 2H MIN (As provided in JIS K5400) Operating force: 0.10~1.96N(10g~200g when using a silicon tipped pen with a 3 mm radius and a hardness of 60 degree.) Transmittance: 78% (Typ.) Driver: Gunze® Touch Panel Device Driver (TPDD). Supports
ページ9に含まれる内容の要旨
5 Package Overview LCD Display Power Adapter Power Cord VGA Signal Cable Audio-in Cable USB Cable RS-232 Cable Landing Strip Touchscreen Driver Installation CD-ROM User’s Guide
ページ10に含まれる内容の要旨
6 Installation Product Overview Front View Back View
ページ11に含まれる内容の要旨
7 Connector Ports “A” Audio VGA RS-232 DC input input Power-in input Connector Ports “B” USB
ページ12に含まれる内容の要旨
8 Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
ページ13に含まれる内容の要旨
9 VESA Mount your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
ページ14に含まれる内容の要旨
10 Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can connect the cables in “Connector Ports A.” 1. To remove the back cover, follow the arrows in Figure A and press with both your thumbs. The cover should be removed by pressing firmly along the edges while pulling on the cover. 2. Follow the instructions on P. 11 ( Figure 11.1 ) to connect the cables in “Connector Ports A.” 3. Fix t
ページ15に含まれる内容の要旨
11 Connecting the Display (Figure 11.1) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC power cord to the power connector on the monitor; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet (11.1 ). 3. Connect the VGA signal cable from the display’s VGA input connector to the 15-pin connector of your host computer and tighten the screws (11.1 ).
ページ16に含まれる内容の要旨
12 Figure 11.1
ページ17に含まれる内容の要旨
13 User Controls Front Panel Controls Control Function No / Icon Menu button Display the OSD menus MENU Select – To select the adjustment items from OSD menus. SELECT/AUTO Select/Auto Auto – To activate the “Auto Adjustment” function to obtain an optimum image. 1. Decreases the brightness of the display Brightness image. Minus/Minus 2. Decreases value of the adjustment items. 1. Increases the brightness of the display Brightness image. Plus/Plus 2.
ページ18に含まれる内容の要旨
14 How to Use the OSD Menus 1. Press the "MENU" button to pop up the “on-screen menu” and to select among the four Main Menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “ ”or “ “ button. 4. The OSD menu will automatically close, if you have left it idle for a pre-set time. 5. To disable the OSD menu buttons, please follow the instructions below: (Please note: the monitor has to be ON with a vali
ページ19に含まれる内容の要旨
15 On-Screen Display Menus Main OSD Menu: MAIN MENU SUB MENU Function Description Auto-Adjustment Choose this function to obtain an optimum No/Yes image. Contrast the contrast of the display image. Adjust 0-100 Brightness Adjusts the brightness of the image. 0-100 Horizontal Position Changes the horizontal position of the image. 0-100 Vertical Position Changes the vertical position of the image. 0-100 Clock Changes the display data frequency to match the frequency of y
ページ20に含まれる内容の要旨
16 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section. Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image. Check to see if the r
