ページ1に含まれる内容の要旨
LA1710R,
LA1710RTR
and LA1710RTC
USER’S GUIDE
www.planar.com
7 7211 PLNR.LA1710REV2.indd 1 211 PLNR.LA1710REV2.indd 1 7 7/27/06 4:02:34 PM /27/06 4:02:34 PM
ページ2に含まれる内容の要旨
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc. Other brands or product
ページ3に含まれる内容の要旨
Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Introduction About the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Installation Product Overview . . . . . . . . . .
ページ4に含まれる内容の要旨
Usage Notice WARNING – To prevent the risk of fi re or shock hazards, do not expose this product to rain or moisture. WARNING – Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit. Do: ❑ Turn off the product before cleaning. ❑ LCD front surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cle
ページ5に含まれる内容の要旨
Introduction About Planar’s LA1710R / LA1710RTR / LA1710RTC The LA17 products all have a 17” fl at panel screen with an active matrix, thin- fi lm transistor (TFT) liquid crystal display (LCD). Features include: ❑ Dual signal input: Analog VGA and Digital DVI-D ❑ Active matrix TFT LCD technology ❑ 1280 x 1024 SXGA resolution ❑ 8 ms GTG with RapidVideo™ Accelerator ❑ 17” viewable display area ❑ 31.5 ~ 80 kHz horizontal scan ❑ 56 ~ 75 Hz refresh rate ❑ 0.264mm x 0.264mm pixel pitch 2 ❑
ページ6に含まれる内容の要旨
Touch Screen for LA1710RTR Resistive for fi nger and pen interface ❑ Surface: Anti-glare treatment ❑ Interface: USB ❑ Durability: 35 million touches at a single point ❑ Hardness: 4H per ASTM D3363-92 ❑ Operating force: Stylus - < 25g average Finger - < 50g average ❑ Transmissivity: 83% (Typ.) +/- 2% ❑ Haze: 5% ❑ Clarity: 80% ❑ Driver: Windows® 95/98/Me/NT/2000/XP, Linux 6 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev
ページ7に含まれる内容の要旨
Touch Screen for LA1710RTC Capacitive for fi nger interface ❑ Surface: Anti-glare treatment ❑ Interface: USB ❑ Durability: 225 million touches in a single location ❑ Hardness: Cannot be scratched using any stylus with Mohs’ rating of less than 6.5 ❑ Transmissivity: up to 88% at 550 mm ❑ Driver: Windows® 95/98/Me/NT/2000/XP, Linux MS HID compatible pointing device LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev.
ページ8に含まれる内容の要旨
Package Overview LCD Display Power Adapter Power Cord VGA Signal Cable Landing Strip Touch Screen Driver Installation CD-ROM (for LA1710RTR/ LA1710RTC) USB Cable DVI Signal Cable (for LA1710RTR/ LA1710RTC) 8 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 7 7211 PLNR.LA1710REV2.indd 8 211 PLNR.LA1710REV2.indd 8 7 7/27/06 4:02:38 PM /27/06 4:02:38 PM
ページ9に含まれる内容の要旨
Installation Product Overview • Front View LCD Display • Rear View Connector Ports “A” Connector Ports “B” LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 9 7 7211 PLNR.LA1710REV2.indd 9 211 PLNR.LA1710REV2.indd 9 7 7/27/06 4:02:39 PM /27/06 4:02:39 PM
ページ10に含まれる内容の要旨
• Connector Ports “A” • Connector Ports “B” USB (For LA1710RTR/LA1710RTC) 10 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 7 7211 PLNR.LA1710REV2.indd 10 211 PLNR.LA1710REV2.indd 10 7 7/27/06 4:02:40 PM /27/06 4:02:40 PM
ページ11に含まれる内容の要旨
Connecting the display (Figure 1.1) To set up this display, please refer to the following fi gure and procedures. 1. Be sure all equipment is off. 2. Connect the DC power cord to the power connector. Plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet(1). 3. For the PC with Analog graphics output: connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws(2). 4. Fo
ページ12に含まれる内容の要旨
Figure 1.1 12 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 7211 PLNR.LA1710REV2.indd 12 7211 PLNR.LA1710REV2.indd 12 7 7/27/06 4:02:41 PM /27/06 4:02:41 PM
ページ13に含まれる内容の要旨
User Controls Front Panel Controls Menu button Displays the OSD menus. Select / Auto Select- To select the adjustment items from OSD menus. Auto- To activate the “Auto Adjustment” function to obtain an optimum image. Brightness Minus 1. Decreases the brightness of the / Minus display image. 2. Decreases value of the adjustment items. Brightness Plus / 1. Increases the brightness of the Plus display image. 2. Increases value of the adjustment items. Power Switch Sw
ページ14に含まれる内容の要旨
How to Use the OSD Menus 1. Press the “Menu” button to pop up the on-screen menu and to select between the four main menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “ ” button. 4. The OSD menu will automatically close, if you have left it idle for a pre-set amount of time. 14 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 7 7211 PLNR.LA1710REV2.indd 14 211 PLNR.L
ページ15に含まれる内容の要旨
On-Screen Display Menus First OSD Menu: ◆ Auto-Adjustment Choose this function to obtain an optimum image. ◆ Contrast This function allows the user to adjust the image crispness. Contrast adjusts the difference between white and black shades. ◆ Horizontal Position Changes the horizontal position of the image. ◆ Vertical Position Changes the vertical position of the image. ◆ Clock Changes the display data frequency to match the frequency of the graphic card. When you are exper
ページ16に含まれる内容の要旨
On-Screen Display Menus Second OSD Menu: ◆ Display Mode Select this function to view the display resolution, vertical refresh, and horizontal scan of the current mode. ◆ OSD Off-Time Adjusts the time it takes for the OSD menu to disappear. ◆ Language Choose the language you need. ◆ Sharpness Adjust the sharpness of the image. ◆ Reset Returns the display parameters of the current mode to the factory default settings. 16 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev.
ページ17に含まれる内容の要旨
On-Screen Display Menus Third OSD Menu: ◆ Volume Controls the sound volume. ◆ Mute Disables the sound immediately. ◆ Input Select Choose the input signal. LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 17 7 7211 PLNR.LA1710REV2.indd 17 211 PLNR.LA1710REV2.indd 17 7/27/06 4:02:44 PM 7/27/06 4:02:44 PM
ページ18に含まれる内容の要旨
On-Screen Display Menus Fourth OSD Menu: ◆ Color Adjusts the color temperature. ◆ Color Adjustment-Red Adjusts the red color of the display. ◆ Color Adjustment-Green Adjusts the green color of the display. ◆ Color Adjustment-Blue Adjusts the blue color of the display. 18 LA1710R, LA1710RTR and LA1710RTC User’s Guide (020-0320-01 Rev. A) 7 7211 PLNR.LA1710REV2.indd 18 211 PLNR.LA1710REV2.indd 18 7 7/27/06 4:02:45 PM /27/06 4:02:45 PM
ページ19に含まれる内容の要旨
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or visit Planar Support at www.planar.com/support. See support contact information on rear cover. Problem: No image appears on screen. ◆ Check that all the I/O and power connectors are installed correctly and well connected as described in the “Installation” section. ◆ Make sure the pins of the connectors are not crooked or broken. ◆
ページ20に含まれる内容の要旨
Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact Planar for more information. ◆ No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphic card. Check all the power switches, power cables, and VGA signal cable. ◆ Going
