ページ1に含まれる内容の要旨
42-inch 3D-Intelligent Display
42-3D6C01/00
42-3D6W01/00
42-3D6C02/00
42-3D6W02/00
User Manual
Philips 3D Solutions
ページ2に含まれる内容の要旨
Warning this is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Safety Instructions for 3D display Read and follow these instructions: 1. This product must be earthed. 2. The mains plug or appliance inlet is used as the disconnect device and should be easily accessible. 3. Use only an approved power cord or interconnection cable. 4. Unplug the product if you
ページ3に含まれる内容の要旨
Mounting The display can be placed on a table stand or wall-mounted. The table stand is supplied as standard; the mounting bracket can be purchased separately. This bracket can also be used as an adapter in combination with universal wall supports, ceiling supports or universal floor stands (e.g. Vogel’s Professional). Fitting the table stand Only use the stand supplied with the set, making sure that the fasteners are properly tightened. Never use a makeshift stand, or legs f
ページ4に含まれる内容の要旨
Avertissement – Ce produit est un produit de classe A. Dans un environnement domestique, ce produit peut causer un brouillage radioélectrique. L’utilisateur pourrait avoir à prendre des mesures appropriées à cet égard. Instructions de sécurité pour l’écran 3D Prière de lire et respecter les instructions suivantes : 1. Cet appareil doit être connecté à la terre. 2. La fiche secteur ou la prise d’entrée de l'appareil est utilisée comme dispositif de débranchement et
ページ5に含まれる内容の要旨
Montage L’écran peut être placé sur un support de table ou monté au mur. Le support de table est fourni avec l’appareil et le support de montage au mur est vendu séparément. Ce support peut également servir d’adaptateur combiné à un support de plafond ou encore à un support mural ou de plancher de type universel (par ex., modèle Vogel Professional). Installation du support de table N’utilisez que le support fourni avec l’ensemble en vous assurant de bien serrer les dispositi
ページ6に含まれる内容の要旨
Document Information Info Content Title 42 inch 3D Display, User Manual (9922 159 01 73 1 090401) Date 01 April 2009 Security The material and the information contained herein are proprietary to Philips 3D Solutions. Copying, reproduction, adaptation, modification or dissemination in whole or part is not permitted without the prior written consent of Philips 3D Solutions. Contact http://www.philips.com/3dsolutions
ページ7に含まれる内容の要旨
Display User Manual 3D Solutions Table of Contents 1 Introduction ............................................................................................................................................................................. 8 2 Product features ................................................................................................................................................................... 9 2.1 Global product features ..............................
ページ8に含まれる内容の要旨
Display User Manual 3D Solutions 1 Introduction The 42-inch 3D display from Philips 3D Solutions offers state-of-the-art lenticular lens design creating a variety of distinct autostereoscopic views. By this the viewer will benefit from the multi-user experience along with a large comfort zone. The 42-inch 3D display is specifically designed for a wide range of applications such as digital signage and information provision. The display is featuring superior lens design and 3D rende
ページ9に含まれる内容の要旨
Display User Manual 3D Solutions 2 Product features 2.1 Global product features Multi-view Lenticular Display o 9 view autostereoscopic 3D display o Non-switchable lenticular technology o Optimal viewing distance: 3 meters (10 feet). o Wide comfort zone for 3D perception o Full brightness, full contrast 1 o 2D-plus-Depth or Declipse input in 3D mode o Protective plate at the front side of the display Advanced display signal processing engine o Integrated 3D display processin
ページ10に含まれる内容の要旨
Display User Manual 3D Solutions 2.2 Technical aspects and details Group Item 42-3D # LCD Type TFT LCD panel Resolution 1920 x RGB x 1080 Pixel pitch 0.4845 mm x 0.4845 mm Effective viewing area 930.24 mm x 523.26 mm Size 42’’ Contrast Ratio 1500:1 Aspect Ratio 16:9 2 Brightness 500 cd/m Response time 8 ms (gray-to-gray) Refresh rate 60 fps Display colors 16.7 M (8 bits RGB) White chromaticity Wx: 0.280 Wy: 0.285 (at 10500 K) Physical Weight (including table 4
ページ11に含まれる内容の要旨
Display User Manual 3D Solutions 2.3 Cosmetic specifications 2.3.1 Description This specification standard is applicable to: 3D-displays supplied by Philips 3D Solutions. 2.3.2 Environmental conditions of inspection The environmental conditions and visual inspection shall be conducted as below. o Ambient temperature in the range 15-25 [ C]. Humidity in the range 25-75 [%RH]. The functional inspection distance of the monitor (measured between the monitor and the inspector’s sight)
ページ12に含まれる内容の要旨
Display User Manual 3D Solutions Foreign material Foreign material appears in display Minor 2.3.4 Inspection Criteria Definition of dot defect: If the size of a dot defect is larger than 0.5 times a single pixel, it can be regarded as one dot defect Bright dot: Dot appears bright and the size is fixed in a black pattern. Dark dot: Dot appears dark and the size is fixed in pure red, green and blue pattern. 2 . 3.4.1 Display defects The size of a circular area is defined by the a
ページ13に含まれる内容の要旨
Display User Manual 3D Solutions Discoloration of the active area circumference can occur and should be treated as normal and will not change the functional performance of the 3D intelligent display. Philips 3D Solutions is not responsible for a poor performance due to a not optimal signal input according to display timing recommendation below Advanced Timing Horizontal pixels Front porch 15 Sync width 48 2 Back porch 48 Scan rate 67.02 kHz Sync + Active lines 1920
ページ14に含まれる内容の要旨
Display User Manual 3D Solutions 3 Scope of supply, Set up and mounting 3.1 Scope of Supply The contents of the box: o Display 42-3D # o Table stand o 3 Mains cords (USA, EU and UK) o DVI cable o CD ROM with: Display Control Tool 3DS Media Player User manuals 3D Sample content o Printed version of the Display user manual (this manual) o Cardboard box with cushions The following items can be purchased separately: o Mounting bracket (Article code: 42-WM) 3.2 Image r
ページ15に含まれる内容の要旨
Display User Manual 3D Solutions 3.3 Connecting the display NEVER (dis)connect DVI when your PC or Display is on. 2D monitor (optional) DVI cable DVI cable PC 3D Display Power cord A second 2D display may be connected to the PC. Only use a DVI cable and graphics card that is compliant with the DVI standard (see reference to DVI standard in section 9). The picture below show the DVI-connector and power connector on the back of the display 1 2 Make sure the PC and Displ
ページ16に含まれる内容の要旨
Display User Manual 3D Solutions 3.4 Cleaning instructions Before cleaning the display, disconnect the power cord and DVI cable. It is preferable to clean the front of the display with the cleaning products listed in the table below. To clean we recommend: cleaning materials e.g. soft cotton cloth window leather Aqueous solution, neutral and weakly e.g. Flux alkaline window cleaner without Ajax additives of abrasive substances: Permitted portion of ammonia < 5 Vol-%, as we
ページ17に含まれる内容の要旨
Display User Manual 3D Solutions 3.5 Disposal of your old product Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and
ページ18に含まれる内容の要旨
Display User Manual 3D Solutions 4 Software installation This chapter contains the prerequisites for the PC hardware and the operating system for the software. First, check whether your PC complies with the requirements that are given in the next sections. Then follow the installation instructions, where you will be guided step by step through the software installation procedure. 4.1 Minimum PC requirements The PC must comply with the following requirements: o Pentium 4, ≥ 3 GHz
ページ19に含まれる内容の要旨
Display User Manual 3D Solutions 5 Environmental Condition Operating Shipping / storage Temperature 0 °C to 35 °C -20 °C to 60 °C Humidity 20 % - 80 % 0% - 95 % No condensation No condensation Air pressure 600 – 1100 mBar 300 – 1100 mBar The display is only used indoor. 01 April 2009 ©2009 Philips Electronics Nederland B.V. 19 of 25
ページ20に含まれる内容の要旨
Display User Manual 3D Solutions 6 Interfaces 6.1 DVI-in Pi Signal Pi Signal Pi Signal n n n 1 T.M.D.S. 9 T.M.D.S. 17 T.M.D.S. Data2- Data1- Data0- 2 T.M.D.S. 10 T.M.D.S. 18 T.M.D.S. Data2+ Data1+ Data0+ 3 T.M.D.S. 11 T.M.D.S. 19 T.M.D.S.Da Data2/4 Data1/3 ta0/5 Shield Shield Shield 4 No 12 No 20 No connect connect connect 5 No 13 No 21 No connect connect connect 6 DDC 14 22 T.M.D.S. +5V Clock Clock Power Shield 7 DDC Data 15 Ground 23 T.M.D.S. Clock+
