ページ1に含まれる内容の要旨
PlasmaSync Plasma Monitor
™
PlasmaSync 60XM5
PX-60XM5A
Start up Guide
Start up Guide
Guide rapide
Guía de inicio
Guia de iniciação
NEC Corporation of America
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Start up Guide (Enhanced split screen Model) For the operation of your plasma monitor, refer to the CD-ROM. Contents User’s Manual on CD-ROM The complete user’s manual is supplied on the CD-ROM in Important Information.................................. En-2 PDF (Portable Document Format) and provides detailed Installation .................................................. En-4 product and useage information for your NEC plasma monitor. Ventilation Requirements for enclosure mounting ...... En-4
ページ4に含まれる内容の要旨
Important Information To avoid damage and prolong operating life: Precautions 1. Use only with 100 V to 240 V 50 Hz/60 Hz AC power supply. Continued Please read this manual carefully before using your plasma monitor and operation at line voltages greater than 100 V to 240 V AC will shorten keep the manual handy for future reference. the life of the unit, and might even cause a fire hazard. 2. Handle the unit carefully when installing it and do not drop. CAUTION 3. Set the unit away from h
ページ5に含まれる内容の要旨
Warning WARNING Not for use in a computer room as defined in the This product equipped with a three-wire grounding Standard for the Protection of Electronic Computer/ (earthed) plug - a plug that has a third (grounding) Data Processing Equipment ANSI/NFPA 75. pin. This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an This equipment has been tested and found to comply outlet, contact a licensed electrician to replace the with the limits for a Class B dig
ページ6に含まれる内容の要旨
Installation You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. * Do not touch or hold the screen face when carrying the unit. • This device cannot be installed on its own. Be sure to use a stand o
ページ7に含まれる内容の要旨
Creating a video wall With built-in matrix display capability, you can create a (22, 33, 44, 55, 51, 15) video wall. • Connect signal cables and remote cables as shown below. Video signal RGB/DVD/HD signal Remote Remote RGB signal/ VIDEO Signal control control DVD/HD signal IN IN IN IN RCA phono plug BNC connector VIDEO AUDIO 1 DVD1 / HD1 AUDIO 2 RGB2 / DVD2 / HD2 RGB 1 AUDIO 3 RGB 3 EXTERNAL CONTROL REMOTE 2 R R R VIDEO AUDIO 1 DVD1 / HD1 AUDIO 2 RGB2 / DVD2 / HD2 RGB 1 AUDIO 3 RGB 3 EXT
ページ8に含まれる内容の要旨
MENU/ENTER DOWNVOLUME UP LEFT/- RIGHT/+ INPUT SELECT /EXIT Top side Caution when placing the plasma monitor in portrait mode • Use the optional mount. Contact your store to purchase before installing. OPTION1 OSM BNC INPUT : RGB D-SUB INPUT • Rotate 90° clockwise as seen from the front when installing. : RGB 90° RGB SELECT : AUTO HD SELECT : 1080B INPUT SKIP • After installing, make sure the NEC logo is located at the : OFF ALL RESET : OFF 1024768 SEL. MENU/ENTER OK EXIT RETUR
ページ9に含まれる内容の要旨
Part Names and Function Front View VOLUME INPUT SELECT MENU/ENTER DOWN UP LEFT/- RIGHT/+ /EXIT VOLUME INPUT SELECT MENU/ENTER DOWN UP LEFT/- RIGHT/+ /EXIT 7 6 5 4 1 3 2 q Power t LEFT/– and RIGHT/+ Turns the monitor’s power on and off. Functions as the CURSOR ( / ) buttons and used to adjust the picture parameters in the On-Screen Menu w Remote sensor window (OSM) mode. Receives the signals from the remote control. y VOLUME DOWN and UP e POWER/STANDBY indicator Adjusts the volume. When the p
ページ10に含まれる内容の要旨
Rear View/ Terminal Board L VIDEO AUDIO 1 DVD1 / HD1 AUDIO 2 RGB2 / DVD2 / HD2 RGB 1 AUDIO 3 RGB 3 EXTERNAL CONTROL REMOTE L/R Y Cb/Pb Cr/Pr L/R R/Cr/Pr G/Y B/Cb/Pb HD VD (IN/OUT) L/R DVI IN OUT BA D VIDEO AUDIO 1 DVD1 / HD1 AUDIO 2 RGB2 / DVD2 / HD2 RGB 1 AUDIO 3 RGB 3 EXTERNAL CONTROL REMOTE 2 R R R 1 (IN/OUT) R/Cr/Pr G/Y B/Cb/Pb HD VD 3 Y Cb/Pb Cr/Pr (IN/OUT) DVI ( Digital RGB ) IN OUT L ( ) (MONO) L MONO L (MONO) CE F G H IJK A AC IN H RGB3 (DVI 24pin) Connect the included power cord here
ページ11に含まれる内容の要旨
u EXIT Remote Control Press this button to exit the OSM controls in the main menu. Press this button during the display of the sub menu to return to the previous menu. i POINTER Press this button to display the pointer. o ZOOM (+ /–) Enlarges or reduces the image. !0 VOLUME (+ /–) Adjusts the audio volume. !1 MUTE Mutes the audio. !2 WIDE Press this button to select and switch the screen sizes. WIDE button is not active for all signals. !3 DISPLAY Displays the source settings on the screen. !4 O
ページ12に含まれる内容の要旨
Basic Operations POWER OFF TIMER To turn the unit ON and OFF: To set the off timer: The off timer can be set to turn the power off after 30, 60, 1. Plug the power cord into an active AC power outlet. 90 or 120 minutes. 2. Press the Power button (on the unit). 1. Press the OFF TIMER button to start the timer at 30 The monitor’s POWER/STANDBY indicator turns red minutes. and the standby mode is set. 2. Press the OFF TIMER button to the desired time. 3. Press the POWER ON button (on the remote cont
ページ13に含まれる内容の要旨
OSM (On Screen Menu) Controls Menu Operations Note: The main menu disappears by pressing the EXIT The OSM window is displayed with respect to the button. screen as shown on the diagram. Information * Depending on the screen’s mode, the OSM may be displayed differently. Advanced menu mode In the explanation, the OSM section is shown close up. When “ADVANCED OSM” is set to “ON” in the main MAIN MENU 1 / 2 menu (1/2), full menu items will be shown. PICTURE AUDIO IMAGE ADJUST OPTION 1 MAIN MENU 1
ページ14に含まれる内容の要旨
* For further details of each menu item, please refer to the CD-ROM. Menu Tree :Shaded areas indicate the default value. ←→: Press the or button to adjust. :Menu items in a ruled box are available when the ADVANCED OSM is set to ON. Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE PICTURE CONTRAST ←→ 0←52→72 YES YES En-21 BRIGHTNESS ←→ 0←32→64 YES YES En-21 SHARPNESS ←→ 0←16→32 YES YES En-21 COLOR ←→ 0←32→64 YES YES En-21
ページ15に含まれる内容の要旨
Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE OPTION2 PWR. MGT. OFF←→ON YES NO En-26 CINEMA MODE OFF←→ON YES NO En-26 LONG LIFE PLE AUTO/LOCK 1/LOCK 2/LOCK 3 YES NO En-26 ORBITER AUTO 1 YES NO En-27 AUTO 2 YES NO En-27 MANUAL H-DOT/V-LINE/TIME YES NO En-27 OFF YES NO En-27 INVERSE OFF YES NO En-27 ON WORKING TIME/WAITING TIME YES NO En-27 WHITE YES NO En-27 SCREEN WIPER OFF YES NO En-28 ON WORKING TIME/WAITING TIME/SPEED YES NO En-28 SOFT FOCUS OFF/1/2/3/4 YE
ページ16に含まれる内容の要旨
Troubleshooting If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service. Symptom Checks Remedy The unit emits a crackling sound. • Are the image and sound normal? • If there are no abnormalities in the image and sound, the noise is caused by the cabinet reacting to changes in temperature. This will not affect performance. Picture is disturbed. • Is a connected component set directly in front or at • Leave some space betwee
ページ17に含まれる内容の要旨
Specifications Screen Size 51.9 inches(H)29.2 inches(V) 1319 mm(H)742 mm(V) 1.8" 3.0" diagonal 60 inches (45) 57.9" (1470) (77) Aspect Ratio 16 : 9 Resolution 1365 pixels(H)768 pixels(V) 51.9" (1319) Pixel Pitch 0.038 inches(H)0.038 inches(V) 0.97 mm(H)0.97 mm(V) Signals Synchronization Range Horizontal : 15.5 kHz to 110.0 kHz (automatic : step scan) Vertical : 50.0 Hz to 120.0 Hz (automatic : step scan) 4.8" Input Signals RGB, NTSC (3.58/4.43), PAL (B,G,M,N), 1 1 1 PAL60, SECAM, HD* , DVD*
ページ18に含まれる内容の要旨
Limited Warranty Plasma Monitors NEC Corporation of America warrants this product to be HOW YOU CAN GET WARRANTY SERVICE free from defects in material and workmanship under the 1. To obtain service on your product, consult the dealer from whom you purchased the product. following terms and, subject to the conditions set forth 2. Whenever warranty service is required, the original dated invoice below, agrees to repair or replace (at NEC Corporation of (or a copy) must be presented as proof of wa
ページ19に含まれる内容の要旨
Guide rapide (Modèle à découpe d’image avancée) Pour le fonctionnement de votre moniteur plasma, référez-vous au CD-ROM. Table des matière Manuel d’utilisation sur CD-ROM Le manuel d’utilisation complet est fourni sur le CD-ROM en Recommandations importantes ..................... Fr-2 format PDF (Portable Document Format) et fournit des Installation .................................................. Fr-4 informations détaillées concernant le produit et son utilisation Ventilation requise pour l
ページ20に含まれる内容の要旨
Recommandations importantes Pour éviter tout dommage et assurer une utilisation durable: Précaution 1. Utiliser seulement une alimentation en courant de 100 V à 240 V 50 Hz/60 Hz. Veuillez lire avec attention ce manuel avant d’utiliser le moniteur à plasma Toute utilisation prolongée avec un courant supérieur à 100 V à 240 V risque et le conserver accessible pour s’y référer ultérieurement. de diminuer la durée de vie de l’appareil et même de provoquer un incendie. 2. Manipuler l’appareil avec p
