ページ1に含まれる内容の要旨
MultiSync LCD1970V
MultiSync LCD1970NX
MultiSync LCD1970NXp
User’s Manual
ページ2に含まれる内容の要旨
Index Warning, Caution .........................................................................................................................English-1 Declaration ...................................................................................................................................English-1 Canadian Department of Communications Compliance Statement ............................................English-2 Declaration of Conformity ......................................................
ページ3に含まれる内容の要旨
ページ4に含まれる内容の要旨
Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specified cables with the MultiSync LCD1970V (L194RK)/MultiSync LCD1970NX (L194RH)/ MultiSync LCD1970NXp (L194RH) colour monitor so as not to interfere with radio and
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
5. Lift up the stand to unlatch the upper hooks and remove the stand (Figure S.3). 6. Remove the 2 screws on the top of the monitor (Figure S.4). The monitor is now ready for mounting in an alternate manner. 7. Connect the cables to the back of the monitor. 8. Reverse this process to re-attach stand. NOTE: Use only VESA-compatible alternative mounting method. Handle with care when removing stand. Figure S.3 Figure S.4 Flexible Arm Installation This LCD monitor is designed for use with a flexible
ページ10に含まれる内容の要旨
Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons (MENU/EXIT, Left, Right, Down, Up). To change signal input, press the SELECT button (NX/NXp only). To change DV MODE, press the RESET button (NX/NXp only). NOTE: OSM must be closed in order to change signal input. LCD1970V LCD1970NX/LCD1970NXp Button Menu MENU/EXIT Open OSM main menu. Exits the OSM controls. Exits to the OSM main menu. 4-Direction
ページ11に含まれる内容の要旨
Colour Control System Colour Control System: Six colour presets select the desired colour setting (sRGB and NATIVE colour presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour will appear on screen and the direction (increase or decrease) will be shown by the bars. NATIVE: Original colour presented by the LCD panel that is unadjustable. sRGB: sRGB mode dramatically improves the colour fidelity
ページ12に含まれる内容の要旨
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabine
ページ13に含まれる内容の要旨
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 50 cm. • Rest
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
Specifications for LCD1970NX Monitor Specifications MultiSync LCD1970NX Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 48.2 cm/19.0 inches liquid crystal display (LCD); 0.294 mm dot 2 3 Native Resolution (Pixel Count): 1280 x 1024 pitch; 250 cd/m * white luminance; 500:1 contrast ratio, typical. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI Sync: Separate sync.TTL Level Horizontal sync. Positive/Negative Vert
ページ16に含まれる内容の要旨
Specifications for LCD1970NXp Monitor Specifications MultiSync LCD1970NXp Monitor Notes LCD Module Diagonal: 48.2 cm/19.0 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 48.2 cm/19.0 inches liquid crystal display (LCD); 0.294 mm dot 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 250 cd/m white luminance; 800:1 contrast ratio, typical. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI Sync: Separate sync.TTL Level Horizontal sync. Positive/Negative Vertic
ページ17に含まれる内容の要旨
Features Thin-frame design creates more desktop space for you to work and play, while the flat screen’s crisp, bright images and crystal- clear text deliver a comfortable viewing experience. No Touch Auto Adjust automatically adjusts your optimal image settings upon initial power-on. Colour Control System allows you to change between six colour settings on your display to match your personal preference. Redesigned OSM controls allow you to quickly and easily adjust all elements of your screen im
ページ18に含まれる内容の要旨
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). For more
