ページ1に含まれる内容の要旨
MultiSync LCD1980SX
User’s Manual
ページ2に含まれる内容の要旨
Index Warning, Caution .................................................................................................... English-1 Declaration .............................................................................................................. English-1 Canadian Department of Communications Compliance Statement ....................... English-2 Declaration of Conformity ....................................................................................... English-2 Contents........
ページ3に含まれる内容の要旨
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
ページ4に含まれる内容の要旨
Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950. FCC Information 1. Use the attached specified cables with the MultiSync LCD1980SX colour monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have bee
ページ5に含まれる内容の要旨
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD1980SX monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (15-pin mini D-SUB male to DVI-A) • Video Signal Cable (DVI-D to DVI-D cable) • User’s Manual • Cable cover • CD ROM (includes complete User’s Manual in PDF format). To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC. Power Cord 15-pin mini D-SUB male to DVI-A Cable Cover User’s Manual DVI-
ページ6に含まれる内容の要旨
Quick Start To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB to DVI-A signal cable to the connector of the display card in your system (Figure A.2). For the MAC: Connect the MultiSync Macintosh cable adapter
ページ7に含まれる内容の要旨
INPUT1 INPUT2 INPUT1 INPUT2 Figure C.2 Figure C.1 NEC-Mitsubishi optional product attachment. Vacation Do not use this connector unless specified. Switch Power Button Figure D.1 Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen. Figure RL.1 Screen Rotation
ページ8に含まれる内容の要旨
Tilt Swivel Grasp top and bottom sides of the monitor screen with your Grasp both sides of the monitor screen with your hands hands and adjust the tilt as desired (Figure TS.1). and adjust the swivel as desired (Figure TS.2). Figure TS.1 Figure TS.2 NOTE: Handle with care when tilting the monitor screen. Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place hands on each side of the monitor and lift up to the highest position
ページ9に含まれる内容の要旨
Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons (EXIT, , , –, +). To change signal input, press the SELECT button. NOTE: OSM must be closed in order to change signal input. Menu EXIT Exits the OSM controls. Exits to the OSM main menu. CONTROL / Moves the highlighted area left/right to select control menus. Moves the highlighted area up/down to select one of the controls. ADJUST - / + Moves the
ページ10に含まれる内容の要旨
FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust function” do not give you a satisfactory picture setting, a fine tuning can be performed manually using the “Fine” function. It improves focus, clearity and image stability by increasing or decreasing this setting. For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like on the left drawing. The image should be
ページ11に含まれる内容の要旨
Tools 2 LANGUAGE: OSM control menus are available in seven languages. OSM POSITION: You can choose where you would like the OSM control image to appear on your screen. Selecting OSM Location allows you to manually adjust the position of the OSM control menu left, right, down or up. OSM TURN OFF: The OSM control menu will stay on as long as it is use. In the OSM Turn Off submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSM control menu. The prese
ページ12に含まれる内容の要旨
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabine
ページ13に含まれる内容の要旨
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 50 cm. • Rest
ページ14に含まれる内容の要旨
Specifications Monitor Specifications MultiSync LCD1980SX Monitor Notes LCD Module Diagonal: 48 cm/19.0 inches Active matrix; thin film transistor (TFT) liquid Viewable Image Size: 48 cm/19.0 inches crystal display (LCD); 0.294 mm dot pitch; 2 Native Resolution (Pixel Count): 1280 x 1024 250 cd/m white luminance, typical; 600:1 contrast ratio, typical. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI Sync: Separate sync.TTL Level Horizontal sync. Positive/Negative Vertical sync. Po
ページ15に含まれる内容の要旨
Features ambix+ Technology: Dual input technology allowing both analog and digital inputs off of one connector (DVI-I) as well as ® additional legacy analog support off of a traditional 15-pin VGA connector. Provides traditional MultiSync technology compatibility for analog as well as DVI-based digital compatibility for digital inputs. DVI-based digital interfaces include DVI-D,DFP and P&D. DVI-I: The integrated interface ratified by the Digital Display Working Group (DDWG) that allows both digi
ページ16に含まれる内容の要旨
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and
ページ17に含まれる内容の要旨
Appendix If you need detailed information about the controls, please use the advanced menu. • Turn off your monitor. • Turn on your monitor by pushing the “POWER” and “SELECT” button at the same time for at least one second simultaneously. • You will see the Advanced menu. This menu is larger than the normal OSM. • Turn off and restart your monitor in the normal way. To make an adjustment, ensure that the tag is highlighted, then pre
ページ18に含まれる内容の要旨
Tag4 Auto Automatically adjusts the Image Position and H. Size (or V. Size) settings and Fine settings. (Analog input only) Press “SELECT” to activate Auto Adjustment. H. Position Controls Horizontal Image Position within the display area of the LCD. Press “+” or “-” to adjust. V. Position Controls Vertical Image Position within the display area of the LCD. Press “+” or “-” to adjust. H. SIZE (OSD Adjusts the horizontal (or vertical) size of the screen. ROTATION: If the “Auto Adjust function” do
ページ19に含まれる内容の要旨
Tag7 Sharpness This is a digital capability for keeping a crisp image at all signal timings. It continuously adjusts to maintain a distinct or soft image as you prefer, and is set independently according to different timings. Press “+” or “-” to select. Expansion Mode Sets the zoom method. FULL: The image is expanded to 1280 x 1024, regardless of the resolution. ASPECT: The image is expanded without changing the aspect ratio. OFF: The image is not expanded. CUSTOM1: Zoom with center fixed. The i
ページ20に含まれる内容の要旨
OSM Rotation To switch OSM between Landscape and Portrait modes. Press “+” or “-” to select. Resolution Notifier The optimal resolution is 1280 x 1024. If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not set to 1280 x 1024. Press “+” or “-” to select. Factory Preset Selecting Factory Preset allows you to reset all OSM control settings (BRIGHTNESS, CONTRAST, IMAGE CONTROLS, COLOR CONTROL SYSTEM, SHARPNESS, EXPANSION MODE, OFF TIMER, OS
