ページ1に含まれる内容の要旨
TM
DiamondPoint V51LCD/V71LCD/V91LCD
DPLCD51V71V91VCover.p65 1 11/19/04, 2:57 PM
ページ2に含まれる内容の要旨
Index Warning .................................................................................................................... 1 Contents ................................................................................................................. 2 Quick Start ............................................................................................................. 3 Controls .............................................................................................................
ページ3に含まれる内容の要旨
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
ページ4に含まれる内容の要旨
Contents Your new Mitsubishi DiamondPoint LCD monitor box* should contain the following: • DiamondPoint LCD monitor • Power Cord • User’s Manual • Video Signal Cable • Base Stand • Cable Holder Power Cord Video Signal Cable DiamondPoint LCD Monitor (Stand not connected) TM DiamondPoint V51LCD/V71LCD/V91LCD Cable Holder User’s Manual *Remember to save your original box and packing material to transport or ship the monitor. 2 DP51V71V91VManual112304.p65 2 11/29/04, 3:36 PM
ページ5に含まれる内容の要旨
Quick Start To attach the Base to the LCD Stand: 1. Insert the front of the LCD Stand into the holes in the front of the Base (Figure 1). 2. Next, position the locking tabs on the back side of the LCD Stand with the holes on the Base. Lower the Stand until locking tabs are secure. 3. Attach the clip into the base (Figure 2). Figure 1 Figure 2 Stand Locking Tabs Front Base To attach the DiamondPoint LCD monitor to your system, follow these instruc- tions: 1. Turn off the power to your computer. 2
ページ6に含まれる内容の要旨
Quick Start –continued Figure A.1 Figure A.2 Note: Some Macintosh systems do not require a Macintosh Cable MacintoshCable Adapter Adapter (not included) Power Cable Input (VGA) Figure B.1 Cable holder Figure C.1 Power button 4 DP51V71V91VManual112304.p65 4 11/29/04, 3:36 PM
ページ7に含まれる内容の要旨
Quick Start –continued Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Figure TS.1 NOTE: Handle with care when tilting the monitor screen. Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1.Disconnect all cables. 2.Place monitor face down on a nonabrasive surface (Figure R.1). 3.Remove the 4 screws connecting the monitor to the stand and slide the stand off from the LCD (Figure R.1). The monitor is
ページ8に含まれる内容の要旨
Quick Start –continued Removing the Base Note: Always remove the Base when shipping the LCD. 1. Place monitor face down on a non-abrasive surface. 2. While using your thumbs, press the tabs in the direction of the arrows to unlock the stand. 3. Pull the unlocked base off the stand. Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor must be
ページ9に含まれる内容の要旨
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: 1. Basic key function –+ AUTO / RESET Button SELECT OSD Off OSD displayed Shortcut to bright Shortcut to contrast “Auto adjust“ adjust window adjust window function OSD On Go to Adjustment Cursor moves left Cursor moves right (Icon selection stage stage) Adjust value Adjust value Reset operation OSD On Go to Icon selection decrease or increase or (Adjustment stage stage) Cursor for adjust Cursor for
ページ10に含まれる内容の要旨
Controls –continued BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST Adjusts the image displayed for non-standard video inputs. AUTO ADJUST Automatically adjusts the Image Position, H. Size and Fine setting. LEFT/RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN/UP Controls Vertical Image Position within the display area of the LCD. H. SIZE Adjusts the horizont
ページ11に含まれる内容の要旨
Controls –continued EXIT Selecting EXIT allows you exit OSD menu/sub menu. LANGUAGE OSD control menus are available in seven languages. OSD TURN OFF The OSD control menu will stay on as long as it is in use. In the OSD Turn OFF submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are 10 - 120 seconds in 5 second intervals. OSD LOCK OUT This control completely locks out access to all OSD control functions without
ページ12に含まれる内容の要旨
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE DIAMONDPOINT LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabi
ページ13に含まれる内容の要旨
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes. Th
ページ14に含まれる内容の要旨
Specifications Monitor DiamondPoint Notes Specifications V51LCD Monitor LCD Module Diagonal: 15.0 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 15.0 inch liquid crystal display (LCD); 0.297 mm dot 2 Native Resolution (Pixel Count): 1024 x 768 pitch; 250cd/m white luminence; 400:1 contrast ratio, typical Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync TTL Level (Positive/Negative) Horizontal sync Positive/Negative Vertical sync Positive/Negative Display Color
ページ15に含まれる内容の要旨
Specifications –continued Monitor DiamondPoint Notes Specifications V71LCD Monitor LCD Module Diagonal: 17.0 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 17.0 inch liquid crystal display (LCD); 0.264 mm dot 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 250cd/m white luminence; 450:1 contrast ratio, typical Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync TTL Level (Positive/Negative) Horizontal sync Positive/Negative Vertical sync Positive/Negative D
ページ16に含まれる内容の要旨
Specifications –continued Monitor DiamondPoint Notes Specifications V91LCD Monitor LCD Module Diagonal: 19.0 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 19.0 inch liquid crystal display (LCD); 0.294 mm dot 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 250cd/m white luminence; 450:1 contrast ratio, typical Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync TTL Level (Positive/Negative) Horizontal sync Positive/Negative Vertical sync Positive/Negative D
ページ17に含まれる内容の要旨
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another. ® AccuColor Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. ® OSD (On-Screen Display) Controls: Allow you to quickly and easily adjust all element
ページ18に含まれる内容の要旨
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and recom
ページ19に含まれる内容の要旨
References NEC-Mitsubishi Monitor Customer Service & Support Customer Service and Technical Support: (800) 632-4662 Fax: (800) 695-3044 Parts and Accessories/Macintosh Cable Adapter: (888) NEC-MITS [888-632-6487] Warranty Information: www.necmitsubishi.com/warranty Online Technical Support www.necmitsubishi.com/support Sales and Product Information Sales Information Line: (888) NEC-MITS [888-632-6487] Canadian Customers: (866) 771-0266, Ext#: 4037 Government Sales: (800) 284-6320 Government S
ページ20に含まれる内容の要旨
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of one (1) year from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and will m
