ページ1に含まれる内容の要旨
ENGLISH ENG
OWNER’S MANUAL
MONITOR SIGNAGE
Please read this manual carefully before operating the your set and
retain it for future reference.
MONITOR SIGNAGE MODELS
47WV30MS
47WV30BR
47WV30BS
47WV30-BAAM
47WV30-BAAL
www.lg.com
ページ2に含まれる内容の要旨
ENGLISH ENG 2 TABLE OF CONTENTS CONTENTS 23 - IR Receiver connection 4 LICENSE 24 Adjusting the screen 24 - Selecting an image mode 24 - Customizing image options 5 ASSEMBLING AND PREPARING 25 - Customizing PC display options 25 Adjusting the sound 5 Unpacking 25 - Selecting an sound mode 6 Parts 26 - Customizing sound options 7 To install in a Portrait Layout 26 Using additional options 7 Remove L-brackets before Installation 26 - Adjusting aspect ratio 8 Moving Handles 8 - Moving the device i
ページ3に含まれる内容の要旨
ENGLISH ENG TABLE OF CONTENTS 3 57 Connecting to the LAN 57 - LAN connection 57 Connecting to a USB 58 Daisy Chain Monitors 58 - RGB Cable 58 - DVI Cable 59 TROUBLESHOOTING 62 SPECIFICATIONS 64 RS-232 CONTROL NOTE y The following three phenomena may occur due to the characteristics of the Super Narrow Bezel LCD. They are not related to the display's performance. 1. The edges of the screen may become darker or shadows may appear. 2. Light leakage may occur depending on the viewing angle.
ページ4に含まれる内容の要旨
ENGLISH ENG 4 LICENSE LICENSE A different license is supported depending on the model. Visit www.lg.com for more information on the license. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to
ページ5に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 5 ASSEMBLING AND PREPARING Unpacking Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. Power Cord RGB Cable DVI Cable CD (Owner's Manual, SuperSign Program, SuperSign Manual) / Card POWER MONITOR ENERGY INPUT ON OFF SAVING . , ! ABC DEF GHI JKL MNO IR Receiver Guide bracket
ページ6に含まれる内容の要旨
ENGLISH ENG 6 ASSEMBLING AND PREPARING Parts < 47WV30MS/47WV30BR > RS-232C DVI OUT DVI IN RGB OUT AUDIO COMPONENT IN SPEAKER USB LAN (CONTROL) (RGB/DVI) /DVI (8Ω) RGB IN REMOTE VIDEO AV IN AUIDO CONTROL IN Connection panel < 47WV30BS/47WV30-BAAM/47WV30-BAAL > RS-232C DVI OUT DVI IN SPEAKER RGB OUT AUDIO USB LAN AUDIO (CONTROL) /DVI (RGB/DVI) (8Ω) RGB IN REMOTE CONTROL IN COMPONENT IN Connection panel
ページ7に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 7 To install in a Portrait Layout When installing in a Portrait Layout, rotate the monitor clockwise 90 degrees (when facing the screen). Remove L-brackets before Installation Remove the L-brackets from each corner of the monitor before installing it. NOTE Keep the removed L-brackets and use them when moving the monitor later.
ページ8に含まれる内容の要旨
ENGLISH ENG 8 ASSEMBLING AND PREPARING Moving Handles Moving the device in a vertical Moving the device in a horizontal position position Hold the vertical handles on the left and right Have the screen facing down and hold the vertical sides or the left and right handles on the back of handles on the left and right sides. the display. Left and right handles at the back Vertical handle Vertical handle on the side on the side RS-232C DVI OUT DVI IN RGB OUT AUDIO SPEAKER USB LAN AUDIO (CONTROL)
ページ9に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 9 STORAGE METHOD FOR PANEL PROTECTION Correct Method Incorrect Method Panel Panel If the product needs to be set upright, hold both sides of the product, and tilt backward carefully If the product is tilted onto the bezel, the bottom of for. Do not let the panel not to touch the floor. the panel may be damaged. Panel Cushion Panel When laying down the product, lay a cushion on a flat floor. Put the product on it with the panel of the product facing down
ページ10に含まれる内容の要旨
ENGLISH ENG 10 ASSEMBLING AND PREPARING Installing on a wall CAUTION y Disconnect the power cord first, and then Install the monitor at least 10 cm away from the move or install the Monitor set. Otherwise wall and leave about 10 cm of space at each side electric shock may occur. of the monitor to ensure sufficient ventilation. De- y If you install the Monitor set on a ceiling or tailed installation instructions can be obtained from slanted wall, it may fall and result in severe your local
ページ11に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 11 EXTERNAL EQUIPMENT SETUP IR RECEIVER This allows a remote control sensor to be placed in a custom location. Then that display can control other displays via an RS-232 cable. Refer to page 19 for more information. AUDIO (RGB/DVI) REMOTE CONTROL IN
ページ12に含まれる内容の要旨
ENGLISH ENG 12 ASSEMBLING AND PREPARING Tiling Displays How to Join Sets - Installing Set 1 *Example of 2 x 2 tiling * The numbers assigned in this example (#1, #2, #3, #4) are used to demonstrate the installation procedure to ensure it is easy to follow. These numbers have nothing to do with the Set ID that is used to operate the remote control. Set the guide bracket into the bracket groove using screws and mount the set to the wall mount plate or the wall. Guide bracket Screws for fixing t
ページ13に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 13 How to Join Sets - Installing Set 2 Join Set 2 to Set 1 using the guide brackets on the top side of Set 1 and mount the two sets to the wall mount plate or the wall. Remove the guide brackets after mounting the sets. Remove the Guide bracket guide brackets How to remove the guide brackets * Unscrew the guide bracket scre
ページ14に含まれる内容の要旨
ENGLISH ENG 14 ASSEMBLING AND PREPARING How to Join Sets - Installing Set 3 Fix the guide brackets to Set 3 following the steps above, and loosely mount the set to the wall mount plate or the wall. #2 #1 #3 Minimize the space between the sides of the sets using the U-shaped fixture. When the sets are joined with the minimum amount of space between them, firmly mount them to the wall mount plate or the wall. When the sets are firmly mounted to the wall
ページ15に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 15 How to Join Sets - Installing Set 4 Loosely mount Set 4 to the wall mount plate or the wall and minimize the space between the sets using the U-shaped fixtures. When Set 4 is firmly mounted to the wall, remove the U-shaped fixtures. Remove the guide brackets. See . Now the 2 x 2 tiling is complete. You can tile in various combinations, such as 3 x 3. Set 4 joined to the rest of the sets (2 x 2 tiling) Wall mount plat
ページ16に含まれる内容の要旨
ENGLISH ENG 16 ASSEMBLING AND PREPARING Inserting the Cable Holder As illustrated, insert two cable holders into the holes at the bottom rear of the set to organize the cable bundles. As illustrated, screw the power cable holder into the hole on the bottom rear of the set to hold the power cables together. (This is to put the power cables inside the holder.)
ページ17に含まれる内容の要旨
ENGLISH ENG REMOTE CONTROL 17 REMOTE CONTROL The descriptions in this manual are based on the buttons of the remote control. Please PO POWER WER read this manual carefully and use the Monitor set correctly. MONI MONI MONIT T TO O OR R R ENERGY ENERGY INPU INPUT T ON ON OFF OFF S SA AV VING ING 11 .. ,, ! ! 22 A AB BC C 33 D DE EF F 44 G GH HII 55 J JK KL L 66 M MN NO O 7777 P PQ QR RS S 88 T TU UV V 99 W WX XY YZ Z To replace batteries, open the battery cover, replace 1 1//a a//A A 00 C CL LE
ページ18に含まれる内容の要旨
ENGLISH ENG 18 REMOTE CONTROL POWER MONITOR ENERGY INPUT ON OFF SAVING 1 . , ! 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ 1/a/A 0 CLEAR - * # MARK POWER ARC P BRIGHT A PSM G NESS E MUTE MEN MENU U A AUT UTO O S S.MENU .MENU OK OK MONITOR ENERGY INPUT BA BACK CK T TILE ILE E EXI XIT T ID ID ON ON OFF OFF OFF ON SAVING . , ! ABC DEF GHI JKL MNO MENU(See p.43) PQRS TUV WXYZ Selects a menu. Clears all on-screen displays 1/a/A CLEAR - * # and returns to Set viewing AUTO MARK from
ページ19に含まれる内容の要旨
ENGLISH ENG POWER POWER MONITOR ENERGY INPUT MONITOR ENERGY INPUT OFF OFF ON ON SAVING SAVING . , ! ABC DEF . , ! ABC DEF GHI JKL MNO GHI JKL MNO REMOTE CONTROL 19 PQRS TUV WXYZ PQRS TUV WXYZ 1/a/A 1/a/A CLEAR CLEAR - * # - * # MARK MARK ARC ARC Displaying the device name connected to an input port P P BRIGHT A BRIGHT A PSM PSM G G NESS NESS E E MUTE MUTE Display which devices are connected to which NOTE external input ports. AUTO S.MENU AUTO S.MENU MENU MENU External inputs
ページ20に含まれる内容の要旨
ENGLISH ENG 20 REMOTE CONTROL Picture ID Picture ID is used to change the settings of a 2 If you press the left/right buttons or press the specific set (display) using a single IR receiver for ON button repeatedly, the Picture ID cycles through OFF and 1 to 4.Assign the ID you multi-vision. The set receiving the IR signal com- want. municates with another set via the RS232 connec- tor. Each set is identified by a Set ID. If you as- sign the Picture ID using the remote control, only displa
