ページ1に含まれる内容の要旨
ENGLISH ENG
OWNER’S MANUAL
MONITOR SIGNAGE
Please read this manual carefully before operating the your set and
retain it for future reference.
MONITOR SIGNAGE MODELS
42VS20
47VS20
55VS20
www.lg.com
ページ2に含まれる内容の要旨
ENGLISH ENG 2 TABLE OF CONTENTS CONTENTS 4 LICENSES 22 ENTERTAINMENT 22 - Connecting to a wired network 23 - Network Status 5 ASSEMBLING AND 24 - Connecting USB storage devices PREPARING 25 - Browsing files 5 Accessories 27 - Viewing movies 6 Optional Accessories 30 - Viewing photos 7 Parts and buttons 33 - Listening to music 8 Connecting the stand (42VS20) 35 - Viewing the Contents List 8 Connecting the stand (47VS20) 36 - DivX® VOD Guide 9 Connecting the stand (55VS20) 37 - Using PIP/PBP 9 C
ページ3に含まれる内容の要旨
ENGLISH LICENSES 3 55 TROUBLESHOOTING 58 SPECIFICATIONS 65 IR CODES 66 CONTROLLING THE MULTIPLE PRODUCT 66 Connecting the cable 66 RS-232C Configurations 66 Communication Parameter 67 Command reference list 69 Transmission / Receiving protocol
ページ4に含まれる内容の要旨
ENGLISH 4 LICENSES LICENSES Supported licenses may differ by model. For more information of the licenses, visit www.lg.com. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. ABOUT DIVX VIDEO: DivX is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified device that plays DivX video. Visit divx.com for more information and software tools to convert your files i
ページ5に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 5 ASSEMBLING AND PREPARING Accessories Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. POWER MONITOR ENERGY INPUT ON OFF SAVING . , ! ABC DEF GHI JKL MNO PQRS TUV WXYZ 1/a/A - * # CLEAR MARK ARC P PSM BRIGHT A NESS G E MUTE AUTO S.MENU MENU OK BACK TILE EXIT ID ON OFF
ページ6に含まれる内容の要旨
ENGLISH ENG 6 ASSEMBLING AND PREPARING Optional Accessories Without prior notice, optional accessories are subject to change to improve the performance of the product, and new accessories may be added. The illustrations in this manual may differ from the actual product and accessories. Stand kit 42VS20 47VS20 55VS20 Stand Stand Stand Screws Screws Screws Speaker kit Cable holder/ Speaker Screws/Cable Cable Tie NOTE y Cable holder/Cable tie may not be available in some areas or for some model
ページ7に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 7 Parts and buttons Screen Buttons Screen Marks RGB/AV USB DP DVI IN DVI OUT /COMPONENT OUT AUDIO LAN SPEAKER IN IN RGB/AV /COMPONENT IN Connection panel (See p.51 to p.53) Screen Marks Description INPUT Changes the input source. MENU Accesses the main menus, or saves your input and exits the menus. Adjust the up and down. Adjusts the volume level. AUTO/SET Displays the current signal and mode. Press this button to adjust the screen automatically (available
ページ8に含まれる内容の要旨
ENGLISH ENG 8 ASSEMBLING AND PREPARING Connecting the stand Connecting the stand (42VS20) (47VS20) - Only on some models. - Only on some models. Place a soft cloth on the table and put the Place a soft cloth on the table and put the 1 1 product with the screen facing downward. product with the screen facing downward. Use the screws to secure the stand on the rear Use the screws to secure the stand on the rear 2 2 side of the product as shown in the diagram. side of the product as shown i
ページ9に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 9 Connecting the stand Connecting the Speakers (55VS20) (42VS20,47VS20) - Only on some models. - Only on some models. Place a soft cloth on the table and put the Connect the input signal cable to the Monitor 1 1 product with the screen facing downward. before installing the speakers. Use a cable tie to organize the cables. Mount the speaker by using a screw as shown 2 in the following. Then connect the speaker cable. Use the screws to secure the sta
ページ10に含まれる内容の要旨
ENGLISH ENG 10 ASSEMBLING AND PREPARING Connecting the Speakers Portrait Layout (55VS20) - Only on some models. - Only on some models. When installing in a Portrait Layout, rotate the Connect the input signal cable to the Monitor 1 monitor clockwise 90 degrees (when facing the before installing the speakers. Use a cable tie screen). to organize the cables. Mount the speaker by using a screw as shown 2 in the following. Then connect the speaker cable. Using the Kensington security system
ページ11に含まれる内容の要旨
ENGLISH ENG ASSEMBLING AND PREPARING 11 Mounting on a wall CAUTION y Disconnect the power cord first, and then For proper ventilation, allow a clearance of 10 move or install the Monitor set. Otherwise cm on each side and from the wall. Detailed electric shock may occur. installation instructions are available from your y If you install the Monitor set on a ceiling or dealer, see the optional Tilt Wall Mounting Bracket slanted wall, it may fall and result in severe Installation and Setu
ページ12に含まれる内容の要旨
ENGLISH ENG 12 REMOTE CONTROL REMOTE CONTROL The descriptions in this manual are based on the buttons of the remote control. Please read this manual carefully and use the Monitor set correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION y Do not mix old and new batteries, as this may damage the remo
ページ13に含まれる内容の要旨
ENGLISH ENG USING THE MONITOR SET 13 POWER MONITOR ENERGY INPUT ON OFF SAVING 1 . , ! 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ 1/a/A 0 - * # CLEAR MARK ARC P BRIGHT A PSM NESS G E MUTE POWER MEN MENU U AUT AUTO O S S.MENU .MENU OK OK BA BACK CK T TILE ILE E EXI XIT T ID ID MONITOR ENERGY INPUT ON ON O OFF FF ON OFF SAVING . , ! ABC DEF GHI JKL MNO MENU (See p.38) PQRS TUV WXYZ Accesses the main menus or saves your input and exit 1/a/A CLEAR - * # menus. AUTO MARK Automaticall
ページ14に含まれる内容の要旨
ENGLISH ENG 14 USING THE MONITOR SET USING THE MONITOR SET RGB connection Connecting to a PC Transmits the analog video signal from your PC to Your Monitor set supports the Plug & Play* feature. the Monitor set. Connect the PC and the Monitor set with the 15 pin signal cable as shown the * Plug & Play: A PC will have a built-in driver for following illustrations. the monitor, no extra software is needed. Select RGB input. Back of the product. RGB/AV /COMPONENT OUT DVI IN AUDIO DP AUDIO IN IN I
ページ15に含まれる内容の要旨
ENGLISH ENG USING THE MONITOR SET 15 DVI connection HDMI connection Transmits the digital video signal from your PC to Transmits the digital video and audio signals from the Monitor set. Connect the PC and the Monitor your PC to the Monitor set. Connect the PC and set with the DVI cable as shown the following the Monitor set with the HDMI cable as shown in illustrations. the following illustrations. Select DVI input. Select HDMI input. Back of the product. Back of the product. RGB/AV /COMPONE
ページ16に含まれる内容の要旨
ENGLISH ENG 16 USING THE MONITOR SET DP connection Transmits the digital video and audio signals from your PC to the Monitor set. Connect the PC and the Monitor set with the DP cable as shown in the following illustrations. Select DP input. Back of the product. RGB/AV /COMPONENT OUT DVI IN AUDIO DP AUDIO IN IN IN RGB/AV /COMPONENT IN (not included) PC NOTE y Sound may not be available depending on the DP version of your PC.
ページ17に含まれる内容の要旨
ENGLISH ENG USING THE MONITOR SET 17 Customizing image options Adjusting the screen Customize basic and advanced options of each Selecting an image mode image mode for the best screen performance. Display images in its optimized settings by Press MENU to access the main menus. 1 selecting one of the preset image modes. Press the Navigation buttons to scroll to 2 Press MENU to access the main menus. 1 PICTURE and press OK. Press the Navigation buttons to scroll to 2 3 Press the Navigation
ページ18に含まれる内容の要旨
ENGLISH ENG 18 USING THE MONITOR SET Advanced Customizes the advanced options. Adjusting the sound Refer to the Advanced image options. Control Selecting an sound mode Picture Reset Restores the options to the default setting. Play the sound in its optimized settings by selecting one of the preset sound modes. When you are finished, press EXIT. 6 Press MENU to access the main menus. 1 When you return to the previous menu, press Press the Navigation buttons to scroll to BACK. 2 AUDIO a
ページ19に含まれる内容の要旨
ENGLISH ENG USING THE MONITOR SET 19 Customizing sound options Using additional options Customize options of each sound mode for the Adjusting aspect ratio best sound quality. Resize the image to view the image at its optimal Press MENU to access the main menus. 1 size by pressing ARC while you are watching Press the Navigation buttons to scroll to 2 Monitor set. AUDIO and press OK. 3 Press the Navigation buttons to scroll to Sound Mode and press OK. CAUTION Press the Navigation buttons
ページ20に含まれる内容の要旨
ENGLISH ENG 20 USING THE MONITOR SET - 16:9 : This selection will allow you to adjust the - 4:3 : This selection will allow you to view a picture horizontally, in linear proportion, to fill the picture with an original 4:3 aspect ratio, black entire screen(useful for viewing 4:3 formatted bars will appear on both the left and right of the DVDs). screen. - Just Scan : This Selection will allow you view - Zoom : This selection will allow you to view the the picture of best quality without
