ページ1に含まれる内容の要旨
GD-171
GD-191
L L L LC C C CD D D D M M M MO O O ON N N NI I I IT T T TO O O OR R R R
U Us se er r’s s G Gu ui id de e
U Us se er r s s G Gu ui id de e
ページ2に含まれる内容の要旨
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed a
ページ3に含まれる内容の要旨
SAFETY INSTRUTIONS 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product and persons ne
ページ4に含まれる内容の要旨
SAFETY INSTRUTIONS F. If the product exhibits a distinct change in performance, indicating a need for service. 15. The Main Plug is used as the disconnect device. Make enough room for inserting and removing the power plug. Place the apparatus as close to the outlet as possible. 16. Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury.
ページ5に含まれる内容の要旨
▶ ▶ ▶ ▶ NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. ▶ ▶ ▶ ▶ DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases. ▶ ▶ ▶ ▶ KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising. Do not
ページ6に含まれる内容の要旨
POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada) and AC 220 – 240 V (For European countries, Asian countries, and United Kingdom). The power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure safety and EMC regulations of each country. • Not all types of power cords are supplied to this product. For European and For U.S.A. and For United Kingdom: Asian count
ページ7に含まれる内容の要旨
CONTENTS SAFETY INSTRUCTION …………………………………………………… 3-4 CAUTION …………………………………..………………………………… 5-6 UNPACKING ………………………………………………………………… 8 CONNECTING WITH EXTERNAL DEVICE ……………………………... 9 CONTROLS and FUNCTIONS ……………………………………………. 10 - 14 APPENDIX ………………………………………………………………...... 15 - 16 TROUBLESHOOTING GUIDE ……………………………………………. 16 - 7 -
ページ8に含まれる内容の要旨
Remove the package cover and place the product on a flat and secure surface or in the installation location. Check whether all the flowing device and accessories are included with the main system. TFT-LCD MONITOR USER MANUAL AC POWER ADAPTOR POWER CORD N.America 3PIN x 1 Warranty Card - 8 -
ページ9に含まれる内容の要旨
REAR PANEL CONTROL 1. DC 12V Power IN 2. RGB IN RGB signal input 3. VIDEO 1(AV1) IN Composite signal input for AV1 4. VIDEO 1(AV1) OUT Composite looping output for AV1 5. VIDEO 2(AV2) IN Composite signal input for AV2 6. VIDEO 2(AV2) OUT Composite looping output for AV2 7, AUDIO L IN Left side audio signal input. This input is for AV1, AV2, S-VIDEO 8. AUDIO R IN Right side audio signal input. This input is for AV1, AV2, S-VIDEO 9. S-VIDEO (Y/C) IN
ページ10に含まれる内容の要旨
KEY FUNCTIONS 1. MENU Activates and exits the OSD. 2. SOURCE/▼ Select input source, and move the OSD menu. 3. AUTO/▲ Move the OSD menu and auto adjustment of RGB source. 4. ◀ ◀ ◀ ◀ (VOL) Decrease the level of volume and select and set the OSD menu. 5. ▶ ▶ ▶ ▶ Increase the level of volume and select and set the OSD menu. 6. /I Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch
ページ11に含まれる内容の要旨
OSD MENU DESCRIPTION MENU SELECTION 1. Press the MENU button to access the Main menu. 2. Use the and arrow buttons to highlight a selection. 3. Press the button to select an item. 4. Use the and arrow buttons to highlight a selection. 5. Use the ◀ and arrow buttons to adjust the setting on a selected item. NOTE : If you don’t use RGB mode, RGB SETUP menu is not selected. ■ INPUT Select Inputs can be set to VIDEO1, VIDEO2, S-VID
ページ12に含まれる内容の要旨
1. Press the MENU button and then ▲/▼ button to select the PICTURE menu. 2. Press the ▶ button and then ▲/▼ button to select the adjustment item you need. 3. Press the ▶ button to active the item. ex) If you select the BRIGHTNESS, then the below picture appears on the bottom of screen. 4. Press “ ◀ ▶” to adjust the item. 5. Press the Menu button to move to the previous menu. NOTE : TINT item is for the NTSC input only. ■ SOUND MENU 1. Press t
ページ13に含まれる内容の要旨
■ RGB SETUP MENU 1. Press the MENU button and then ▲/▼ button to select the RGB SETUP menu. 2. Press the ▶ button and then ▲/▼ button to select the adjustment item you need. 3. Press the ▶ button to active the item. 4. Press ◀ ▶ to adjust the item 5. Press the MENU button to move to the previous menu. ■ FUNCTION MENU - 13 -
ページ14に含まれる内容の要旨
1. Press the MENU button and then ▲/▼ button to select the FUNCTION menu. 2. Press the ▶ button and then ▲/▼ button to select the adjustment item you need. 3. Press the ▶ button to select the item. 4. Press the MENU button to move to the previous menu. LANGUAGE: Select the language: ENGLISH, FRANCE, GERMAN, ITALIAN, SPANISH. BUTTON LOCK: Select Button lock ON don’t work the Front key. Release the button lock: Push the ▲ and ◀ ◀ ◀ ◀ arrow at the same time for 5 sec then the bu
ページ15に含まれる内容の要旨
- 14 SPECIFICATIONS VIDEO Screen Size 17” 19” Viewing Area 338.0 x 270.0mm 376.0 x 301.0mm Pixel Type Active Matrix TFT Max. Resolution 1280 x 1024 @ 60Hz (SXGA) Pixel Pitch 0.264 x 0.264mm 0.294 x 0.294mm Brightness 250 cd/㎡ Contrast Ratio 800 : 1 Aspect Ratio 5 : 4 Viewing Angle (H/V) 85” /85”/ 75”/ 85” (R/L/T/B) Display Color 16.7 Million Response Time < 5ms Video System NTSC / PAL Frequency (H) 31 ~ 63kHz Frequency (V) 55 ~ 75Hz Panel Lamp Life 50,000hours MECANI
ページ16に含まれる内容の要旨
D-SUB CONNECTOR PIN ASSIGMENTS PIN ASSIGNMENT Pin No. Pin Name Pin No. Pin Name 1 RED VIDEO 9 NC 2 GREEN VIDEO 10 GROUND 3 BLUE VIDEO 11 GROUND 4 NC 12 SDA (for DDC) 5 GROUND 13 H-SYNC 6 RED GROUND 14 V-SYNC 7 GREEN GROUND 15 SCL (for DDC) 8 BLUE GROUND TROUBLESHOOTING GUIDE Troubleshooting Troubleshooting Tip 1. Make sure if the power supply is connected property. No picture 2. Turn on the power. 3. Select the input signal right for the connected
