ページ1に含まれる内容の要旨
AQ5311D
AQ5311D BK
ENGLISH
USER MANUAL
TABLE OF CONTENTS DEUTSCH
FOR YOUR SAFETY .............................................................................. 1
FRANCAIS
SAFETY PRECAUTIONS ................................................................. 1
SPECIAL NOTES ON LCD MONITORS ............................................. 3
CUSTOMER SERVICE ...................................................................... 3 NEDERLANDS
CLEANING ......................................................
ページ2に含まれる内容の要旨
FCC DECLARATION OF CONFORMITY Model Number: AQ5311D / AQ5311D BK Trade Name: iiyama Responsible party: IIYAMA North America, Inc. Address: 1560 Brookhollow Drive, Suite 208, Santa Ana, CA 92705 U.S.A. Telephone number: 714-437-5111 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ope
ページ3に含まれる内容の要旨
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock. DO NOT PUT ANY OBJECT INTO THE MON
ページ4に含まれる内容の要旨
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor, and that all cables are routed such that children may
ページ5に含まれる内容の要旨
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitors and do not indicate a problem. NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to its correct position. Due to the nature of the backlight, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may fin
ページ6に含まれる内容の要旨
BEFORE YOU OPERATE THE MONITOR Please remove the stopper pin on the back of the stand before you install the monitor. Careful attention is required as the monitor is sprung loaded and may expand quickly when removing it. FEATURES 52.8cm (20.8") TFT Color LCD Monitor Supports Resolutions up to 2048 × 1536 (QXGA) Super Wide Viewing Angle and High Resolution Digital Character Smoothing Stopper pin Automatic Set-up Plug & Play VESA DDC2B Compliant ® Windows 95/98/2000/Me/XP Compliant P
ページ7に含まれる内容の要旨
CONTROLS AND CONNECTORS < Front > < Back > Power Indicator A Green: Normal operation NOTE Orange: Power Management The monitor enters into power management mode which reduces the power consumption to less than 13.5W when receiving no horizontal and/or vertical sync signal. Power Switch B Menu Button C / Contrast Button D / Brightness Button E Exit Button F Keyhole for Security Lock G NOTE You can fasten a security lock and cable to prevent the monitor from being removed without your permission
ページ8に含まれる内容の要旨
CONNECTING YOUR MONITOR Ensure that both the computer and the monitor are switched off. A Connect the computer to the monitor with the signal cable. (See page 21 for CONNECTOR PIN B ASSIGNMENT.) Connect the AC Adapter to the Connector for AC Adapter of the monitor. C Connect the Power Cable to the AC Adapter first and then to the power supply. D NOTE The signal cables used for connecting the computer and monitor vary by the type of computer used. An incorrect connection may cause serious damag
ページ9に含まれる内容の要旨
[Cable Wiring] Collect cables at the back of the stand. A Place the Cable Cover by inserting the tabs into B guide holes and then sliding the cover downward. [AC Adapter Installation] Screw (Accessory) Attach the AC Adapter Holder to the A AC Adapter. Cavity Place the AC Adapter Holder by B inserting the tabs into the cavities on the back of the monitor. Tighten the Screw to fasten the AC C AC Adapter Holder Adapter Holder. (Accessory) AC Adapter Bundle up the adapter cable with the (Accessory)
ページ10に含まれる内容の要旨
COMPUTER SETTING Signal Timing When you connect the monitor to the computer for the first time, set the signal timing of the computer to VGA before connection. Change to the desired signal timings listed on page 20 in COMPLIANT TIMING, after you confirm that the picture appears normally at VGA. Windows 95/98/2000/Me/XP Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP by connecting the monitor to DDC2B compliant
ページ11に含まれる内容の要旨
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s height and angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor’s height or angle. You are able to adjust the monitor’s height up to 110mm 110 mm, angle up to 35 degrees right and left, 35 35˚ degrees upward. NOTE Do not touch the LCD screen when you change the height or the angle. It ma
ページ12に含まれる内容の要旨
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 20. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS. Press the Menu Button to start the On Screen Display feature. Move the cursor ( by using the / Buttons. Select the adjustment icon relating to the adjustment you want to make by B using the / B
ページ13に含まれる内容の要旨
ADJUSTMENT MENU CONTENTS Direct You can skip the Menu display and perform an adjustment immediately by using the following button operations. Brightness: Press the Brightness Button when the Menu is not displayed. Contrast: Press the Contrast Button when the Menu is not displayed. Automatic set-up: Press the and Buttons at the same time when the Menu is not displayed. Analog / DVI-Analog Input Adjustment Item Problem / Option Button to Press Too dark 1 BRIGHTNESS * Di
ページ14に含まれる内容の要旨
Adjustment Item Problem / Option Button to Press Too far to the left H-POSITION Too far to the right Too low V-POSITION Too high NORMAL The picture is displayed at the optimum resolution. 3 IMAGE SIZE * EXPANDED Stretch the picture to fit the full screen. ENGLISH English LANGUAGE FRANCAIS French DEUTSCH German ITALIANO Italian ESPANOL Spanish Japanese JAPANESE You can set the OSD display duration time OSD TIME between 5 and 60 seconds. The model name, year of manufacture
ページ15に含まれる内容の要旨
DVI-Digital Input Adjustment Item Problem / Option Button to Press Too dark 1 Direct BRIGHTNESS * Too bright Too dull Direct CONTRAST Too intense PRESET1 9300K COLOR PRESET2 6500K PRESET3 5500K USER RED Too weak MODE GREEN Too strong BLUE H-POS Too far to the left OSD POSITION Too far to the right V-POS Too low Too high ANALOG Select the Analog RGB input. INPUT SELECTION DVI-ANALOG Select the DVI-Analog input. DVI-DIGITAL Select the DVI-Digital input. NORMAL The pictur
ページ16に含まれる内容の要旨
SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input. The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. They are unlike the adjustments you would make on a CRT monitor. The monitor is designed to provide the best performance at resolution of 2048 × 1536, but can not provide the best at resolutions of less than 2048 × 1536 bec
ページ17に含まれる内容の要旨
Select AUTO in IMAGE SET-UP and perform the Automatic set-up. C Or press the and Buttons at the same time when the Menu is not displayed. (Direct adjustment) Adjust the image manually by following procedure below when the screen has a flicker or D blur, or the picture does not fit in the display area after performing the Automatic set-up. Adjust the V-POSITION so that the top and bottom of the picture frame will fit to the E display area. 1) Adjust the H-POSITION so that the left side of the p
ページ18に含まれる内容の要旨
Adjust the FINE in IMAGE SET-UP to correct horizontal wavy noise, flicker or blur in the G zebra pattern. NOTE In case the strong flicker or blurs remain on a part of the screen, repeat steps and F G because the COARSE may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from again. C Adjust the H-POSITION after the FINE adjustment if the horizontal position moves during the adjustment. Adjust the BRIGHTNESS a
ページ19に含まれる内容の要旨
POWER MANAGEMENT FEATURE The power management feature of this product automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be
ページ20に含まれる内容の要旨
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your deale
