ページ1に含まれる内容の要旨
HP LP2275w and LP2475w LCD Monitors
User Guide
ページ2に含まれる内容の要旨
© 2008 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. All other product names mentioned herein may be trademarks of their respective companies. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use
ページ3に含まれる内容の要旨
About This Guide This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supp
ページ4に含まれる内容の要旨
iv About This Guide
ページ5に含まれる内容の要旨
Table of contents 1 Product Features HP LP2275w Model .............................................................................................................................. 1 HP LP2475w Model .............................................................................................................................. 2 2 Safety and Maintenance Guidelines Important Safety Information ........................................................................................................
ページ6に含まれる内容の要旨
Using the On-Screen Display Menu .................................................................................. 25 OSD Menu Selections ....................................................................................... 25 Optimizing Digital Conversion ........................................................................... 30 Using the HP Display Assistant Utility ............................................................................... 30 Identifying Monitor Conditions ........
ページ7に含まれる内容の要旨
1 Product Features HP LP2275w Model The LCD (liquid crystal display) monitor has an active matrix, thin-film transistor (TFT). The monitor features include: Large 55.88 cm (22-inch) diagonal viewable area display with 1680 × 1050 resolution, plus full- ● screen support for lower resolutions Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side ● Pivot capability to rotate display to portrait mode ● ● Tilt, swivel, and height adjustment capabilities ● Rem
ページ8に含まれる内容の要旨
AssetControl ● Compliant with the following regulated specifications: ● ◦ European Union CE Directives ◦ Swedish MPR II 1990 HP LP2475w Model The LCD (liquid crystal display) monitor has an active matrix, thin-film transistor (TFT). The monitor features include: ● Large 60.96 cm (24-inch) diagonal viewable area display with 1920 × 1200 resolution, plus full- screen support for lower resolutions ● Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side ● Pi
ページ9に含まれる内容の要旨
Software and documentation CD that includes HP Display Assistant, Pivot Pro software, monitor ● driver software, and product documentation ● Energy saver feature to meet requirements for reduced power consumption AssetControl ● Compliant with the following regulated specifications: ● ◦ European Union CE Directives ◦ Swedish MPR II 1990 ◦ Swedish TCO Requirements ◦ Energy Star HP LP2475w Model 3
ページ10に含まれる内容の要旨
2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with the monitor, refer to the Power Cord Set Requirements on page 46 in Appendix C. WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding feature. The grounding plug is an important
ページ11に含まれる内容の要旨
Maintenance Guidelines To enhance the performance and extend the life of the monitor: ● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If the monitor is not operating properly or has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider. Use only a power source and connection appropriate for this monitor, as indicated on the label/ ● back plate of the monitor
ページ12に含まれる内容の要旨
3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow the instructions below. NOTE: Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master power switch turns off all power to the monitor. Installing the Monitor Pedestal Base NOTE: Do not install the pedestal base if the monitor will be used on a wall, swing arm, or other mounting fixture; i
ページ13に含まれる内容の要旨
Rear Components Monitor rear components vary by model. HP LP2275w Model Figure 3-2 Rear Components Table 3-1 HP LP2275w Rear Components Component Function 1 Cable Lock Provision Provides slot for use with cable security locks. 2 Master Power Switch Turns off all power to the monitor. 3 AC Power Connector Connects the AC power cord to the monitor. 4 DisplayPort Connector Connects the DisplayPort signal cable to the monitor. 5 DVI-I Connector Connects the DVI to VGA signal cable or DVI to DVI-D
ページ14に含まれる内容の要旨
HP LP2475w Model Figure 3-3 Rear Components Table 3-2 HP LP2475w Rear Components Component Function 1 Cable Lock Provision Provides slot for use with cable security locks. 2 Master Power Switch Turns off all power to the monitor. 3 AC Power Connector Connects the AC power cord to the monitor. 4 DisplayPort Connector Connects the DisplayPort signal cable to the monitor. 5 HDMI Connector Connects the HDMI signal cable to the monitor. 6 DVI-I Connectors Connects the DVI to VGA signal cable or DVI
ページ15に含まれる内容の要旨
Selecting and Connecting the Signal Cables The monitor signal inputs vary by model. The following table indicates which input video signal is supported on each monitor model. NOTE: Refer to Rear Components on page 7 for signal input connector locations. The monitor will automatically determine which inputs have valid video signals. The inputs can be selected through the On-Screen Display (OSD) feature by pressing the Input button (HP LP2275w Model) or the Quick Select button (HP LP2475w Model) o
ページ16に含まれる内容の要旨
Table 3-3 Signal Connectors and Cables (continued) Input Monitor Connector and Cable Connection Description Plug Component (Y Pb Connect a set of Component cables to the Component connectors on Pr) the monitor and the Component connectors on the input device for analog operation. Cable purchased separately. (HP LP2475w) S-Video Connect an S-Video cable to the S-Video connector on the monitor and the S-Video connector on the input device for analog operation. (HP LP2475w) Cable purchased separat
ページ17に含まれる内容の要旨
Connecting the Monitor Power 1. Place the monitor in a convenient, well-ventilated location near the computer. 2. Connect one end of the power cable to the AC power connector on the back of the monitor (1), and the other end to an electrical wall outlet (2). Figure 3-4 Connecting the Power Cable WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a
ページ18に含まれる内容の要旨
Connecting USB Devices The monitor provides USB connectors on the side panel and on the rear panel that can be used to connect devices such as a digital camera, USB keyboard, or USB mouse. 1. Connect one end of the USB hub cable to the USB connector on the rear panel of the computer, and the other end to the upstream USB connector on the monitor. 2. Connect the USB devices to the USB downstream connectors on the rear or side panel of the monitor. Figure 3-5 Connecting USB Devices 12 Chapter 3
ページ19に含まれる内容の要旨
Cable Management Place the cables through the cable management channel on the back of the monitor base. Figure 3-6 Using the Cable Management Feature Adjusting the Monitor 1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level. Figure 3-7 Tilting the Monitor Cable Management 13
ページ20に含まれる内容の要旨
2. Swivel the monitor to the left or right for the best viewing angle. Figure 3-8 Swiveling the Monitor 3. Adjust the monitor's height so that it is parallel to your eye height for a comfortable viewing position. A lock-down/release button on the front of the column prevents the display head from sliding up when the monitor is lifted. If the display head is locked in the lowest height position: a. Make sure that the monitor is safely positioned on a stable surface. b. Gently push down on the di
