ページ1に含まれる内容の要旨
HP LE1901wi, L1910i, and LE1911i LCD
Monitors
User Guide
ページ2に含まれる内容の要旨
© 2007, 2008, 2009 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services . Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions
ページ3に含まれる内容の要旨
About This Guide This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supp
ページ4に含まれる内容の要旨
iv About This Guide ENWW
ページ5に含まれる内容の要旨
Table of contents 1 Product Features HP LCD Monitors with Integrated Work Center .................................................................................... 1 2 Safety and Maintenance Guidelines Important Safety Information ................................................................................................................ 3 Maintenance Guidelines ....................................................................................................................... 3 Clean
ページ6に含まれる内容の要旨
Using the HP Display Assistant Utility ............................................................................... 27 Identifying Monitor Conditions ............................................................................................................ 27 Sleep Timer Mode .............................................................................................................................. 28 HP Display LiteSaver ...................................................................
ページ7に含まれる内容の要旨
Disposal of Waste Equipment by Users in Private Household in the European Union ................................................................................................................................. 45 HP Recycling Program ...................................................................................................... 45 Chemical Substances ........................................................................................................ 45 Restriction of Hazardous Substan
ページ8に含まれる内容の要旨
viii ENWW
ページ9に含まれる内容の要旨
1 Product Features HP LCD Monitors with Integrated Work Center The flat panel monitors have an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor models include: LE1901wi model, 48.2 cm (19-inch) diagonal viewable area with 1440 x 900 resolution, plus full- ● screen support for lower resolutions; includes custom scaling for maximum image size while persevering original aspect ratio ● L1910i model, 48.3 cm (19-inch) diagonal viewable area display with 1280 × 1024
ページ10に含まれる内容の要旨
AssetControl (available with select models) ● Compliant with the following regulated specifications: ● ◦ European Union CE Directives ◦ Swedish MPR II 1990 ◦ Swedish TCO Requirements 2 Chapter 1 Product Features ENWW
ページ11に含まれる内容の要旨
2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with the monitor, refer to Power Cord Set Requirements on page 43 in Appendix C. WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding feature. The grounding plug is an important safe
ページ12に含まれる内容の要旨
not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A) for each device. ● Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord. ● Turn the monitor off when not in use. You can substantially increase the life expectancy of the monitor by using a screen saver program and turning off the monitor when not in use. N
ページ13に含まれる内容の要旨
3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow the instructions below. Installing the Monitor on the Stand CAUTION: Do not touch the surface of the LCD panel. Pressure on the panel may cause non- uniformity of color or disorientation of the liquid crystals. If this occurs the screen will not recover to its normal condition. 1. Place the monitor panel face down on a dry, soft cloth and co
ページ14に含まれる内容の要旨
2. Place the stand on a desktop or table and push the neck on the stand down to its lowest position. Slide the monitor all the way onto the stand so that the Quick Release mounting device emits an audible click and is locked in place. Figure 3-2 Installing the Monitor on the Stand 3. Route the monitor VGA and power cables through the cable guides at the bottom corners of the mounting panel (select models). Figure 3-3 Routing Monitor VGA and Power Cables 4. To install an HP USDT computer on the
ページ15に含まれる内容の要旨
Installing an HP Ultra-slim Desktop (USDT) on the Stand You can install an HP USDT or Thin Client computer on the rear side of the stand. This section provides instructions on installing the USDT. 1. On the rear of the stand, remove the two screws (1) from the top of the computer mounting bracket and lift the bracket off the stand (2). Figure 3-4 Removing the Computer Mounting Bracket ENWW Installing an HP Ultra-slim Desktop (USDT) on the Stand 7
ページ16に含まれる内容の要旨
2. Use the four screws provided to install the computer mounting bracket on the USDT computer. NOTE: There are two sets of screw holes on the computer mounting bracket. Use the four holes that are offset to install the USDT. Be sure to install the computer mounting bracket on the USDT so that the rear ports on the USDT are toward the right when viewed from the rear of the monitor stand. (The rear ports should be toward the left when viewed from the front of the monitor.) Figure 3-5 Installing t
ページ17に含まれる内容の要旨
cables), up through the bottom hole of the USDT computer's port cover (1) and then connect the cables to the rear of the computer (2). 5. Plug the computer and monitor power cables into an electrical wall outlet (3). Figure 3-7 Connecting the Cables 6. Insert the hooks on the port cover into the slots on the rear of the USDT chassis and slide the port cover down so that it locks in place. Figure 3-8 Installing the Port Cover ENWW Installing an HP Ultra-slim Desktop (USDT) on the Stand 9
ページ18に含まれる内容の要旨
7. Slide the power supply tray out from the base of the stand (1) and place the USDT power supply into the tray (2). Route any loose cables through the cables guides on the sides of the tray (3). Figure 3-9 Installing the Power Supply 8. Be sure the final configuration has the USDT properly oriented, as shown in the illustration below. Figure 3-10 Proper Assembly of Integrated Work Center WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord
ページ19に含まれる内容の要旨
Installing an HP Thin Client on the Stand You can install an HP USDT or Thin Client computer on the rear side of the stand. This section provides instructions on installing the Thin Client. 1. On the rear of the stand, remove the two screws (1) from the top of the computer mounting bracket and lift the bracket off the stand (2). Figure 3-11 Removing the Computer Mounting Bracket 2. Remove the HP logo panel from the right side of the Thin Client to access the screw holes for the computer mountin
ページ20に含まれる内容の要旨
3. Use the four screws provided to install the computer mounting bracket on the Thin Client computer. NOTE: There are two sets of screw holes on the computer mounting bracket. Use the four holes that are centered on the bracket to install the Thin Client. Be sure to install the computer mounting bracket on the Thin Client so that the rear ports on the Thin Client are facing down and the feet on the Thin Client are facing outwards. Figure 3-13 Installing the Computer Mounting Bracket on the Thin
