ページ1に含まれる内容の要旨
Colour Plasma Display Monitor
USER'S MANUAL
Model PW1
MANUEL UTILISATEUR
32PD5000
BEDIENUNGSANLEITUNG
42PD5000
42PMA500
System Name
32PD5000 42PD5000
32PD5100 42PD5100
32PD5200 42PD5200
READ THE INSTRUCTIONS INSIDE CAREFULLY.
KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your monitor.
SERIAL NO.
The serial number is located on the rear of the monitor.
This monitor is ENERGY STAR® compliant when used with a computer equipped with
VESA DPMS.
The
ページ2に含まれる内容の要旨
NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA and XGA are registered trademarks of International Business Machines Corporation. APPLE and Macintosh are registered trademarks of Apple Computer, Inc. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. All brand or product names are trademarks or registered trademar
ページ3に含まれる内容の要旨
USER'S MANUAL Thank you very much for purchasing the HITACHI Plasma Display Monitor. Before using your monitor, please carefully read the "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to operate the monitor properly. Keep this manual in a safe place. You will find it useful in the future. Notes on lnstallation Work: This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence. Always have an installation specialist or your d
ページ4に含まれる内容の要旨
Important FEATURES Please read this User's Manual thoroughly, especially the Safety Instructions on Page 4 to 7. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to Large-screen, high-definition plasma display yourself. Should you encounter any difficulty in the set-up or panel operation of your monitor, firstly refer to the Troubleshooting guide at The 42-inch colour plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, and the
ページ5に含まれる内容の要旨
CONTENTS FEATURES ....................................................2 OTHER FEATURES ....................................21 SAFETY INSTRUCTIONS ..............................4 Automatic Store ................................................................21 COMPONENT NAMES ..................................8 Signal Check ....................................................................22 Main Unit..............................................................................8 Power Save Mo
ページ6に含まれる内容の要旨
SAFETY INSTRUCTIONS This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions. About the Symbols Various symbols are used in this manual, the user’s manual and on the product itself to ensure cor
ページ7に含まれる内容の要旨
WARNING Be cautious of the power cord connection. Incorrect connection of the power cord could result in fire or electrical shock. • Do not touch the power cord with a wet hand. • Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug. • Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure. • Do not cut off the fitted power plug, the removal of which could lea
ページ8に含まれる内容の要旨
SAFETY INSTRUCTIONS(continued) CAUTION Be careful in moving the monitor. Neglect could result in an injury or damage. • Do not move the monitor during use. Before moving, disconnect the power plug and all external connections. • You are advised to move the monitor with two persons. • Avoid any impact or shock to the monitor; particularly take care of glass screen. Do not put anything on top of the monitor. Placing anything on the monitor could result in loss of balance or falling, and cause an
ページ9に含まれる内容の要旨
• Prevention of an obstacle to Radio receivers This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers. - Keep the monitor away from Radio. - Adjust Radio antennas in order for the monitor not to receive interference. - The antenna cable of Radio should be kept away from the monitor. - Use a coaxial cable for antenna. You can check if this monitor influences Radio receivers by turning off all other equipment other than the moni
ページ10に含まれる内容の要旨
COMPONENT NAMES Front Main Unit Cabinet Panel (front frame) Control panel • Adjustment buttons are located on the bottom. • The back cover is provided with Remote-control indications to distinguish the 9 receiver adjustment buttons. Indicating lamp 13 • The main power switch is located at the back, on the lower surface. MENU button 16 Main power switch 13 ▼ INPUT SELECT button 14 VOLUME (OK button) (42") UP/DOWN RECALL button 15 14 buttons ( SELECT button) ( ADJUST 15 SIZE button buttons)
ページ11に含まれる内容の要旨
Remote control POWER OFF button 13 13 POWER ON/OFF button POWER ON button 13 MUTE button 14 14 VOLUME UP/DOWN buttons VOL RGB/VIDEO buttons 14 RGB 1 RGB 2 MUTE VOL 15 SIZE button PinP button 34 AV1 AV2 AV3 AV4 AUTO button 16 15 AUTO PinP SIZE RECALL RECALL button MENU MENU button 16 16 RETURN button OK OK button 16 16 ID ID SET SELECT/ADJUST buttons 16 ID SET button ID button 16 Handling the Remote Control Loading Batteries 1. Open the battery cover. Use the remote control within about 5 m
ページ12に含まれる内容の要旨
INSTALLATION INSTRUCTIONS Installation • If you have purchased the model without the stand attached: When installing the monitor, use the optional Desk-top Stand (CMPAD23/25). The Desk-top Stand has been used for the illustrations in this manual. WARNING Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutel
ページ13に含まれる内容の要旨
4 7 Read SAFETY INSTRUCTIONS ( to ) carefully to ensure maximum safety before proceeding to these steps: • Choose an appropriate site and install the product on a level table where the stand is secure. • Install the monitor to have ready access to a power socket available. • Make sure that the power switch of this device is turned off. Connecting to a PC (1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this device.
ページ14に含まれる内容の要旨
INSTALLATION INSTRUCTIONS (continued) Mounting the Speaker Unit (option) Refer to the instruction manual concerning mounting of the optional speaker unit. Power Cord Connection Connect the power cord, after completing all other connections. ① ➁ ① Connect the power cord to this device. ➁ Connect the power cord plug to the power outlet. (The type of plug is different from this drawing for some countries.) CAUTION • Use only the power cord provided. • Do not use a power supply voltage other than t
ページ15に含まれる内容の要旨
OPERATING INSTRUCTIONS Turning Power On and Off • To turn the monitor power ON, press the main power switch on the monitor main unit to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control. Indicating lamp • To turn the monitor power OFF, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then press the main power switch on the Main power switch monitor main unit to OFF. • During normal use, the main power switch is set in the O
ページ16に含まれる内容の要旨
OPERATING INSTRUCTIONS (continued) Volume Adjustment The volume can be adjusted by pressing the VOL+ and VOL- buttons of the remote control (or the ▲ and ▼ volume buttons of the monitor unit). Volume setting value ▼ Volume 15 VOLUME UP/DOWN buttons INPUT SELECT button Adjustment status guide display • When a button is pressed, the volume adjustment MUTE button status guide will be displayed. ▲ • The volume will increase when the VOL+ (or ) button is pressed while the guide is being displayed.
ページ17に含まれる内容の要旨
RGB 1 RGB 2 MUTE VOL AV1 AV2 AV3 AV4 AUTO PinP SIZE RECALL RECALL button MENU OK SIZE button ID ID SET RECALL button SIZE button Size Switching Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in sequence and the status will be displayed at the bottom of the screen. Normal Full Zoom1 * Real Zoom3 Zoom2 * Real mode gives the image of the same shape as it is displayed on a computer monitor. This mode i
ページ18に含まれる内容の要旨
OPERATING INSTRUCTIONS (continued) Using the Menu Screen (On-screen display system) VOL RGB 1 RGB 2 MUTE VOL When the MENU button is pressed, the adjustment menu AV1 AV2 AV3 AV4 screen will be displayed; from there, PC signal adjustment RETURN buttons and setting is possible by using the SELECT button, AUTO PinP SIZE RECALL AUTO button ADJUST button and OK button. MENU • Refer to - concerning the adjustment items and the 17 21 MENU button SELECT/ADJUST settings. OK but
ページ19に含まれる内容の要旨
▼ PICTURE MENU Picture Picture Audio Contrast : + 31 OK OK Timer Brightness : – 31 Function Colour : 0 MENU Setup Hue : + 31 Language Picture Enhancement : Off Select Colour Temperature : Normal OK Set Colour Temp.Adjust Reset Reset Contrast + 31 Select Set Return OK Next / Prev Adjust Return Picture Contrast : + 31 OK Brightness : – 31 Colour : 0 Hue : + 31
ページ20に含まれる内容の要旨
▼ ▼ OPERATING INSTRUCTIONS (continued) AUDIO MENU Picture Audio Audio Audio Mode : Movie OK Timer Treble : + 10 Function Bass : – 10 MENU Setup Balance : 0 L R Language SRS TruBass : Middle Select Matrix Surround : Off OK Set Perfect Volume : Off Reset Reset Select Set Return Selected characters Setup hint Movie: This selects the audio suitable for Movie. Music: This selects the audio suitable for Music.
