ページ1に含まれる内容の要旨
MONITOR UNIT MU-201CE/MU-231CE
OPERATOR'S MANUAL
This manual describes only the key operations of the monitor unit MU-210CE/MU-231CE.
For other details, refer to the installation manual and operator’s manual of the ECDIS/radar.
1. Overview
When the monitor unit MU-201CE or MU-231CE is connected to a radar/ECDIS
with an RS-232C cable, the keys on the panel are locked, so independent
operation of the keys is not possible. Brilliance is controlled from ECDIS/radar.
Key function under
ページ2に含まれる内容の要旨
2. Menu Operation 1. Press the Menu key to open the main menu. The chosen menu item is circumscribed with a blue rectangle and its sub-menu is displayed below the main menu. Scroll 2. Press the + or – key to choose a menu and press the Enter key. 3. Press the + or – key to choose a sub-menu item and press the Enter key. There are four kinds of items available in each sub-menu. A brief explanation of each follows. Keys They just need to be confirmed for selection in or
ページ3に含まれる内容の要旨
3. Menu Functions This section of the manual describes each function of each menu in detail. Each paragraph represents a given menu. On the left, an image shows all items that can appear in that menu, while on the right an item by item description is given, in the same order as shown at the screen. Each paragraph is named after the menu it represents, and the icon for that menu is shown near the menu name. Please note that the numeric values shown in the boxes are meaningless and do not r
ページ4に含まれる内容の要旨
Main window image settings Backlight Adjust the intensity of the backlight of the display. This is automatically adjusted by radar/ECDIS. LED level Adjust the intensity of the LED on the front panel. Brightness Make the picture brighter or darker. Contrast View dark details on dark backgrounds. This setting should be adjusted after the brightness so as to make the white color as bright as possible without interfering with grays. Sharpness Make the picture more or less detailed. M
ページ5に含まれる内容の要旨
General monitor settings Freeze frame This function, when activated, freezes the image on the screen, disregarding the input signal until deactivated. Source information This setting allows the user to disable the source information that appears on the upper left hand corner each time a source is detected or Input key is pressed. Always use On state. OSD timeout Choose how much time the GUI will remain displayed on the screen when no control is being used. When the user is not touc
ページ6に含まれる内容の要旨
Keypad lock Set whether the keypad is locked or not. When locked, the keypad does not answer to user commands, unless the LOCK key is pressed together with a desired key. If the monitor is connected to radar/ECDIS with an RS-232C cable, Off returns to On after turning the power off and then on. Serial protocol Choose how the equipment will respond to ECDIS commands. In Standard ECDIS mode, the equipment will be compliant with the ECDIS specification, while in ISIC ECDIS mode the val
ページ7に含まれる内容の要旨
Input selection Source Choose the input source for the main screen. As soon as a change is made here, the corresponding input will be selected and activated for display on the main screen. To change the active source for the PIP window, use the PIP menu. Source enable items These menu items allow the user to disable some sources. When a source is disabled (set to Off), it cannot be selected by means of the Input key on the monitor's keypad. 7
ページ8に含まれる内容の要旨
Main screen acquisition settings This menu is available when PIP is set to ON. (See next page.) Mode selection Choose a memory slot in which to store display parameters for a given input signal. Once stored in a memory slot, the settings for the current input signal can be modified at will, and they will be reapplied when the same source is detected again. Mode details This box shows what's inside the memory slot selected with the Mode selection setting. Load current mode This st
