ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Elo Entuitive Touchmonitor User Guide 15" LCD Panel Mount Touchmonitor 1566L Series Revision B P/N 008531 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
ページ3に含まれる内容の要旨
ページ4に含まれる内容の要旨
Copyright © 2001 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
ページ5に含まれる内容の要旨
ii
ページ6に含まれる内容の要旨
Table of Contents Chapter 1 Chapter 4 Introduction 1 Troubleshooting 23 Precautions . . . . . . . . . . . . . . . . . . . . 1 Solutions to Common Problems . . . . . . . . 23 About the Product . . . . . . . . . . . . . . . . . 1 Appendix A Chapter 2 Native Resolution 25 Installation and Setup 3 Appendix B Unpacking Your Panel Mount Touchmonitor . . . . . . . . . . . . . . . . . . 4 Touchmonitor Safety 27 Product Overview . . . . .
ページ7に含まれる内容の要旨
iv
ページ8に含まれる内容の要旨
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive LCD panel mount touchmonitor. Your new high-resolution industrial touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in LCD display design. This combination of features creates a natural flow of information between you and your touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to m
ページ9に含まれる内容の要旨
Auto adjustment capability High quality full screen re-scaling Multilingual OSD menus in four languages: English, German, Spanish, and Japanese Corded remote OSD controller VESA DDC 1/2B data communication VESA DPMS power saving VESA flat panel monitor physical mounting interface (75mm) 19 inch computer hardware rack adaptor available. Contact the factory. Worldwide agency approvals that include UL*, CUL*, TÜV- Bauart, FCC, CE, C-Tick, VCCI • Certified by UL to NEMA 4, 4x and
ページ10に含まれる内容の要旨
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to install your LCD panel mount touchmonitor and how to install Elo TouchSystems driver software. 2-3
ページ11に含まれる内容の要旨
Unpacking Your Panel Mount Touchmonitor Check that the following 10 items are present and in good condition: Brick power supply Video cable AUTO/SEL DOWN UP MENU LCD Display Serial touchscreen cable OSD module Monitor power cable (US/Canada) Elo QuickStart CD Software User Guide European monitor power cable (Note: shipments to the UK will also contain a UK power cord.) User’s Guide, Quick Start Guide and software CD 2-4 Elo Entuitive Tou chmon ito r User Guide
ページ12に含まれる内容の要旨
Product Overview Main Unit LCD Display Rear View 2-5
ページ13に含まれる内容の要旨
Bottom View Customer Panel Remote OSD with Cable Attachment AUTO/SEL DOWN UP MENU 2-6 Elo Entuitive Tou chmon ito r User Guide
ページ14に含まれる内容の要旨
Mounting Your Touchmonitor NOTE: You will need a 6mm allen socket and torque wrench (Hex) to attach the mounting brackets. Your panel mount touchmonitor comes with 6 mounting brackets (and 6 screws). You will need 6 brackets to mount your touchmonitor. Two brackets attach to the top and bottom and one on each side. To mount your touchmonitor to a panel, follow the steps below: 1 Prepare the opening in the panel (307mm x 398.2mm/12.08" x 15.68"). See page C-36. Mounting panel thickness must n
ページ15に含まれる内容の要旨
Connecting Your Touchmonitor The following illustrations guide you step by step in connecting your touchmonitor. Before connecting the cables to your touchmonitor and PC, be sure that the computer and the touchmonitor are turned off. Serial cable Video cable US power cable OSD Module connector Power European power cable Female 15-pin Serial video touchscreen Brick connector connector power supply Connections on underside AUTO/SEL DOWN UP MENU 2-8 Elo Entuitive Tou chmon ito r User Guide
ページ16に含まれる内容の要旨
STEP 1-Connecting the Video Cable Connections on underside Female 9-pin serial touchscreen connector Serial touchscreen cable Connect the 15-pin video cable (the ferrite bead end) to the video port on your PC. Connect the other end of the video cable to the video connector on your touchmonitor. Secure the cable to your touchmonitor and PC by turning the screws on the connector clockwise. 2-9
ページ17に含まれる内容の要旨
STEP 2-Connecting the Serial Touchscreen Cable Connections on underside Female 9-pin Serial touchscreen connector Serial touchscreen cable Connect the female end of the serial (RS-232) cable to the serial port on the back of your PC. Connect the male end of the cable to the serial touchscreen connector on your touchmonitor. Secure the cable to your touchmonitor and PC by turning the screws on the connector. 2-10 Elo En tuitive Touchmonitor User Gu ide
ページ18に含まれる内容の要旨
STEP 3-Connecting the Power Cable Connections on underside Brick power cable port Power switch Power Brick power supply cable Depending on where you live, you will use either the European or US/Canadian power cable. Connect the female end of the power cable to the Brick power supply. Connect the Brick power supply into the power port on the touchmonitor. To protect your equipment against risk of damage from electrical surges in the power line, plug the brick supply’s power cord into a s
ページ19に含まれる内容の要旨
Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmonitor to work with your computer. The enclosed CD-ROM contains drivers for the following operating systems: Windows 2000 Windows Me Windows 98 Windows 95 Windows NT 4.0 Windows 3. x MS-DOS 2. x or later Additional drivers and driver information for other operating systems (including OS/2, Macintosh, and Linux) are available on the Elo TouchSystems Web site at www.elotouch.com. Your
ページ20に含まれる内容の要旨
Installing the Serial Touch Driver To install your driver software, follow the instructions in the appropriate following section. Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature for the CD-ROM drive is active, the system automatically detects the CD and starts the setup program. 2 Follow
