ページ1に含まれる内容の要旨
Touchcomputer User Guide
15A1 15" LCD Multifunction Touchcomputer
ページ2に含まれる内容の要旨
Elo TouchSystems Touchcomputer User Guide 15" LCD Multifunction Touchcomputer ESY15A1 Revision C P/N E362310 Elo TouchSystems 1-800-557-1458 www.elotouch.com
ページ3に含まれる内容の要旨
Copyright © 2008 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no re
ページ4に含まれる内容の要旨
Table of Contents Chapter 1 Ethernet ................................................... 22 Setup 6 Serial ........................................................ 22 Unpacking Your Touchcomputer ......................... 6 Microphone Input .................................... 22 Product Overview ................................................ 7 Audio Output ........................................... 22 Front View .................................................... 7 VGA .....................
ページ5に含まれる内容の要旨
Environmental Specifications ...................... 43 Temperature Ranges .............................. 43 Humidity ................................................ 43 Altitude .................................................. 43 Chapter 6 Technical Support 44 Technical Assistance .................................... 44 Using the Touchcomputer ..................... 44 Using the Web ....................................... 44 Using the Phone .................................... 44 Regulatory Inf
ページ6に含まれる内容の要旨
C H A P T E R 1 Setup This chapter discusses how to set up and test your touchcomputer and any included peripheral options. Unpacking Your Touchcomputer Check that the following items are present and in good condition: Touchcomputer Power cable US/Canadian European power cable PS/2 Y-cable DB9 adapter cable CD and Quick Install Guide Power Adapter Elo TouchSystems 15A1 User Guide 6
ページ7に含まれる内容の要旨
Product Overview Front View Note: Shown with optional peripherals Rear View Elo TouchSystems 15A1 User Guide 7
ページ8に含まれる内容の要旨
Side View Base Bottom View Note: Shown with optional peripherals Elo TouchSystems 15A1 User Guide 8
ページ9に含まれる内容の要旨
Display Orientation Elo TouchSystems 15A1 User Guide 9
ページ10に含まれる内容の要旨
Display Orientation with Peripherals Elo TouchSystems 15A1 User Guide 10
ページ11に含まれる内容の要旨
Initial Turn-On The initial setup of the operating system takes approximately 5-10 minutes. Additional time may be needed depending on touchcomputer hardware configuration and connected devices. To setup the Windows OS for the touchcomputer, turn on the touchcomputer and follow the instructions on the screen. Language Selection When the following window appears, you have the option of changing the language used in menus and dialogs. Click Customize. The Regional and Language window shown below w
ページ12に含まれる内容の要旨
Select the Language tab. The window shown below will appear. Select the desired language in the drop-down list labeled Language used in menus and dialogs. Elo TouchSystems 15A1 User Guide 12
ページ13に含まれる内容の要旨
Time-zone selection When the following window appears, you may change the time-zone, date, and/or time of the touchcomputer. After making any changes, click Next to finish. Windows Setup will complete the initialization of the touchcomputer. Elo TouchSystems 15A1 User Guide 13
ページ14に含まれる内容の要旨
Test Devices The touchcomputer can be pre-installed with several different hardware options. To test an optional device that is installed on the touchcomputer, follow the instructions below. NOTE: Testing icons are located on the desktop. Testing of a particular device can only be done after the device is properly installed. Testing the Touchscreen The touchscreen is pre-calibrated for accurate touch response. Calibration* If for any reason the touchscreen needs to be re-calibrated, double-click
ページ15に含まれる内容の要旨
Testing the Magnetic Stripe Reader (MSR) (optional) Testing in USB MSR Keyboard (KB) Emulation Mode 1. Double-click the KB MSR Test icon to open the Notepad application 2. Slide the card through the MSR and verify that the data is displayed in the application window. Testing in USB MSR Human Interface Device (HID) Mode 1. Double-click the HID MSR Test icon to start the test application. 2. Click the Read Cards button. 3. Slide the card through the MSR and verify that the data is displayed in the
ページ16に含まれる内容の要旨
Converting MSR from Keyboard Emulation to HID and vice versa 1. Double-click the MSR Change Mode icon to start the switch application. 2. Click on HID Mode to switch to HID mode OR click on Keyboard Mode to switch to Keyboard mode. The dimmed box will indicate the current setting. 3. Click Quit to close the window. Elo TouchSystems 15A1 User Guide 16
ページ17に含まれる内容の要旨
Testing the Customer Display (optional) 1. Double-click the CustDisplay Test icon. 2. Verify that the device shows "EloTouch Systems Customer Display" on the display. Testing the Cash Drawer Port To test the cash drawer port, first ensure that a cash drawer port is attached to the touchcomputer using a cable with the correct wiring definition. For additional information, see Cash Drawer Port Signal Definition and Control section on page 35. 1. Double-click the Cash Drawer Test icon to start the
ページ18に含まれる内容の要旨
C H A P T E R 2 Operation This chapter shows the user how to control the On-Screen Display (OSD) and Power buttons, use the I/O panel, securely mount the touchcomputer and adjust the display head. All adjustments made to the OSD and Power controls are automatically saved. User settings will remain unchanged after powering off/on or in the case of a power failure. Elo TouchSystems 15A1 User Guide 18
ページ19に含まれる内容の要旨
OSD Control OSD Menu To display the OSD Menu, press the Menu button. 1. Press the UP button or DOWN button to toggle and the SELECT button to select among the different OSD sub-menus and functions. 2. When the function you want to change is shown, press the SELECT button. To adjust the value of the function: 1. Pressing the UP button increases the value of the selected OSD control option. 2. Pressing the DOWN button decreases the value of the selected OSD control option. The OSD provides the fol
ページ20に含まれる内容の要旨
Factory Reset Changes all OSD settings to factory default. Color Reset Changes all OSD color settings to factory default. Position Reset Changes all OSD position settings to factory default. Sharpness Adjusts the sharpness of the display. Volume Adjusts the audio signal level of the internal speakers and audio output. Information The current OSD version is displayed in the exit tab of the main menu. The current resolution and refresh rates are displayed at the bottom of every OSD menu. Shortcut
