ページ1に含まれる内容の要旨
Elo Entuitive Touchmonitor User Guide
15" LCD Desktop Touchmonitor with Magnetic Swipe Reader (USB)
1525L Series
Revision A
P/N 008569
Elo TouchSystems, Inc.
1-800-ELOTOUCH
www.elotouch.com
ページ2に含まれる内容の要旨
Copyright © 2002 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
ページ3に含まれる内容の要旨
Table of Contents Chapter 1 Chapter 3 Introduction 1 Operation 25 Precautions . . . . . . . . . . . . . . . . . . . . 1 About Touchmonitor Adjustments. . . . . . . . 25 Using the On-Screen Display (OSD) Menus . . 25 Side Bezel Buttons . . . . . . . . . . . . . . . 26 Chapter 2 OSD Menu Function . . . . . . . . . . . . . . 27 Installation and Setup 3 Chapter 4 Unpacking Your Touchmonitor. . . . . . . . . . . 3 Troubleshooting 29
ページ4に含まれる内容の要旨
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in LCD display design. This combination of features creates a natural flow of information between a user and your touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. See Appen
ページ5に含まれる内容の要旨
Auto adjustment capability High quality full screen re-scaling Multilingual OSD menus in four languages: English, French, German, Spanish, and Japanese Serial or USB touch interface (USB requires Windows 98, 2000, Me and XP.) Built in speakers Patented touch technology of Elo TouchSystems VESA DDC 1/2B data communication VESA DPMS power saving Stand with minimum 45° angle of tilt. Cable management device VESA flat panel monitor physical mounting interface (75mm) OSD and
ページ6に含まれる内容の要旨
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 8 items are present and in good condition: OR USB touchscreen Serial touchscreen cable cable LCD Display European monitor power cable Video cable Quick Install Guide CD Software Speaker cable Speaker Cable Monitor power cable User Guide-on CD, (US/Canada) Quick Install Guide and so
ページ7に含まれる内容の要旨
Product Overview Main Unit LCD Display Stand Rear View 2-4 Elo Entuitive Tou chmon ito r User Guide
ページ8に含まれる内容の要旨
Side View User Controls Base Bottom View 2-5
ページ9に含まれる内容の要旨
Touch Interface Connection NOTE: Your interface cables may have been pre-connected to your monitor at the factory. Your touchmonitor comes with one of the following touchscreen connector cables: Serial (RS-232) cable or USB cable. (For Windows 98, 2000, Me and XP systems only.) To set up this display, please refer to the following figures and procedures: Serial Connection The following illustrations guide you step by step in connecting your touchmonitor using a serial cable connection. CAUTI
ページ10に含まれる内容の要旨
STEP 1-Removing the Back Cover Bottom cut-out The cables are routed through the back of the stand. To remove the back cover, place one hand at the top of the stand and your other hand on the bottom cut-out. Pull forward from the bottom cut-out and twist the cover until it snaps off. The cable ports are located on the underside of your touchmonitor. 2-7
ページ11に含まれる内容の要旨
STEP 2-Connecting the Video Cable Connections on underside Female video connector Cable management clip Video Video cable port Ferrite bead Tilt the screen up and back to access the connection ports. Connect the 15-pin video cable (the ferrite bead end) to the video port on your PC. Connect the other end of the video cable to the video connector on your touchmonitor by routing the cable through the hole in the stand. Secure the cable to your touchmonitor and PC by turning the screws
ページ12に含まれる内容の要旨
STEP 3-Connecting the Serial Touchscreen Cable Connections on underside Female 9-pin Serial Touchscreen connector Serial Touchscreen cable Connect the female end of the serial (RS-232) cable to the serial port on the back of your PC. Connect the male end of the cable to the serial touchscreen connector on your touchmonitor. Secure the cable to your touchmonitor and PC by turning the screws on the connector. Route the cable through the cable management clip. 2-9
ページ13に含まれる内容の要旨
STEP 4-Connecting the Speaker Cable Connections on underside Speaker port Speaker cable NOTE: If you do not wish to connect the speaker cable, go to step 5. To use the built in speakers, you need to connect the speaker cable. Connect the speaker cable to the speaker port inside the back of your touchmonitor. Connect the other end of the cable to the speaker connector on your PC. 2-10 Elo En tuitive Touchmonitor User Gu ide
ページ14に含まれる内容の要旨
STEP 5-Connecting the Power Cable Connections on underside AC power cab le port Cable management clip Power cable Depending on where you live, you will use either the European or US/Canadian power cable. Connect the female end of the power cable to the power port on the touchmonitor. Route the cable through the cable management clip. NOTE: To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord into a surge protector
ページ15に含まれる内容の要旨
USB Connection NOTE: A USB connection can only be used if your PC is running Windows 98, 2000, Me or XP. The following illustrations guide you step by step in connecting your touchmonitor using a USB cable connection. CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the computer and the touchmonitor are turned off. USB touchscreen cable Speaker cable Video cable Removable back cover Monitor power cable (US/Canada) Speaker port European monitor power cable Female
ページ16に含まれる内容の要旨
STEP 1-Removing the Back Cover Bottom cut-out The cables are routed through the back of the stand. To remove the back cover, place one hand at the top of the stand and your other hand on the bottom cut-out. Pull forward from the bottom cut-out and twist the cover until it snaps off. The cable ports are located on the underside of your touchmonitor. 2-13
ページ17に含まれる内容の要旨
STEP 2-Connecting the Video Cable Connections on underside Female 15-pin video connector Cable management clip Video Video cable port Ferrite bead Tilt the screen up and back to access the connection ports. Connect the 15-pin video cable (the ferrite bead end) to the video port on your PC. Connect the other end of the video cable to the video connector on your touchmonitor by routing the cable through the hole in the stand. Secure the cable to your touchmonitor and PC by turning the
ページ18に含まれる内容の要旨
STEP 3-Connecting the USB Touchscreen Cable Connections on underside USB touchscreen connector Cable management clip USB touchscreen cable Connect the USB touchscreen cable to the USB touchscreen connector on the touchmonitor. Connect the other end of the USB touchscreen cable to your PC. The touchscreen cable connectors should fit snugly into the connectors on your touchmonitor and PC. Route the cable through the cable management clip. 2-15
ページ19に含まれる内容の要旨
STEP 4-Connecting the Speaker Cable Connections on underside Speaker port Speaker cable NOTE: If you do not wish to connect the speaker cable, go to step 5. To use the built in speakers, you need to connect the speaker cable. Both ends of the speaker cable are identical, so you can connect either end of the speaker cable to the speaker port inside the stand of your touchmonitor. Connect the other end of the cable to the speaker connector on your PC. 2-16 Elo En tuitive Touchmonitor User G
ページ20に含まれる内容の要旨
STEP 5-Connecting the Power Cable Connections on underside Power cable Depending on where you live, you will use either the European or US/Canadian power cable. Connect the female end of the power cable into the power port on the touchmonitor. Route the cable through the cable management clip. NOTE: To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord into a surge protector, and then connect the surge protector to
