ページ1に含まれる内容の要旨
User’s Manual
Monochrome LCD Monitor
It shall be assured that the final system is in compliance
to IEC60601-1-1 requirements.
ページ2に含まれる内容の要旨
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Power supplied equipment can emit electromagnetic waves, that could
ページ3に含まれる内容の要旨
English TABLE OF CONTENTS PRECAUTIONS ...................................................................................4 1. INTRODUCTION .....................................................................................9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors .............
ページ4に含まれる内容の要旨
English PRECAUTIONS IMPORTANT! This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below). [Location of the Caution Statements] IN [Symbols on the unit] Symbol Location This symbol indi
ページ5に含まれる内容の要旨
English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage. Do not open the cabinet or modify the unit. Opening the cabinet or modifying the unit may result in fire, electric shock, or burn. Refer all servicing to qualified service personnel. Do not attempt to service
ページ6に含まれる内容の要旨
English WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. To disconnect the power cord, grasp the plug firmly and pull. Tugging on the cord may damage and result in fire or electric shock. OK The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. Use the correct voltage. * The unit
ページ7に含まれる内容の要旨
English WARNING Do not touch a damaged LCD panel directly with bare hands. The liquid crystal that may leak from the panel is poisonous if it enters the eyes or mouth. If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor. Follow local regulation or laws for safe disposal. The backlight of the LCD panel contains mercury. CAUTION Handle with care when carrying the unit. Disconnect the pow
ページ8に含まれる内容の要旨
English CAUTION Unplug the unit before cleaning it. Cleaning the unit while it is plugged into a power outlet may result in electric shock. If you plan to leave the unit unused for an extended period, disconnect the power cord from the wall socket after turning off the power switch for the safety and the power conservation. LCD Panel In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, please use the monitor with the brightness below 400 2 cd/m (
ページ9に含まれる内容の要旨
English 1. INTRODUCTION Thank you very much for choosing an EIZO Monochrome Monitor. 1-1. Features DVI (p. 40) Digital input (TMDS (p. 41)) compliant Resolution: 1 M pixels (1280 x 1024) Horizontal scanning frequency: 27 - 82 kHz (Digital input: 27 - 64 kHz) Vertical scanning frequency: 50 - 85 Hz (1280 x 1024 ~ 75 Hz) (Digital input: 60 Hz (VGA text: 70 Hz)) RGB Color video signal compatibility Auto Adjustment compliant USB (Universal Serial Bus) hub supported (p.27) The he
ページ10に含まれる内容の要旨
English 1-3. Controls & Connectors Front (2) (1) Control Panel SIGNAL AUTO ENTER 1 - 2 (5) (3) (4) (6) (7) (8) (1) ScreenManager (2) Main Power Switch *1 (3) SIGNAL 1-2 Signal selection button (Color/Monochrome) (4) AUTO Auto Adjustment Button (5) ENTER Enter Button *2 (6) Control Buttons (Left, Down, Up, Right) (7) Power Button *3 (8) Power Indicator Green Operation Orange Power saving Flashing orange (2 times Power save mode Digital only for each) Flashing orange slowly Power
ページ11に含まれる内容の要旨
English Rear (9) (10) Bottom (14)(15) (16) (11)(12)(13) *4 (9) Height Adjustable Stand (Detachable) *5 (10) Security Lock Slot (11) SENSOR Serial Port (Mini DIN 8 pin) (for factory use) (12) IN Serial Port (Mini DIN 6 pin) (for factory use) (13) DVI-I Input Connector (14) USB Port (2 Downstream) (15) USB Port (1 Upstream) (16) Power Connector *4 The LCD monitor has the capability of the Portrait/Landscape display. (The panel pivots in the counter-clockwise direction 90 .) The LC
ページ12に含まれる内容の要旨
English 2. CABLE CONNECTION 2-1. Before connecting Before connecting your monitor to the PC, change the display screen settings (resolution p. 41) and frequency) in accordance with the charts below. NOTE When your computer and display support VESA DDC, the suitable resolution and the refresh rate are set by just plugging your display into the computer without any manual settings. Analog Input Resolution Frequency Dot Clock Remarks 640 × 480 ~ 85 Hz VGA, VESA 720 × 400 70 Hz VGA TEXT
ページ13に含まれる内容の要旨
English 2-2. Connecting the signal cable NOTE Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners. Power Cord Analog Input Signal Cable Connector PC Signal Cable (FD-C16 enclosed) Video Output Analog graphics board Connector D-Sub mini 15 pin [BNC cable] BNC conne
ページ14に含まれる内容の要旨
English [Signal selection] Please use the signal select button on the front panel. (1) The selection menu appears by pressing the button for more than 2 seconds. (2) Choose “Monochrome” by up and down keys. SIGNAL AUTO ENTER 1 - 2 Signal selection button (Color / Monochrome) Digital Input Signal Cable Connector PC Signal Cable (FD-C04 / FD-C35 / Video Output Monochrome digital graphics FD-C39 enclosed) Connector DVI board NOTE Only TMDS DATA1 (Green) of video signal data is displayed.
ページ15に含まれる内容の要旨
English Cable Holder 4. Plug the other end of the power cord into a power outlet. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. Not doing so may result in fire or electric shock. 5. Turn on the monitor's main power and the
ページ16に含まれる内容の要旨
English 3. ScreenManager 3-1. How to use the ScreenManager Control Buttons Left, Down, Up, Right SIGNAL AUTO ENTER 1 - 2 Auto Adjustment button Enter button 1. Entering the ScreenManager Push the Enter button once to display the main menu of the ScreenManager. [Main Menu ] 2. Making Adjustments and Settings (1) Select the desired sub menu icon using the Control buttons and push the Enter button. The sub menu appears. (2) Use the Control buttons to select the desired setting ico
ページ17に含まれる内容の要旨
English 3-2. ScreenManager Adjustments and Settings. The following table shows all the ScreenManager’s adjustment and setting menus. “*” indicates adjustments of analog input only and “**” indicates digital input only. Main menu Sub menu Reference * Screen Clock 4-1. Screen Adjustment (p.20) * Phase Position Resolution * Range Adjustment Brightness Smoothing * Signal Filter Decrease the slightly shadowed images or characters (p.32) Unlock Unlock the lock (p. 19) *1 *2 LUT Setting De
ページ18に含まれる内容の要旨
English 3-3. Useful Functions Adjustment Lock Use the “Adjustment Lock” function to prevent any accidental changes. Locked function • Settings in the ScreenManager. • Signal selection button (Color/Monochrome) Unlocked function • Adjustment of brightness by the control buttons. [How to lock] (1) Switch off the monitor’s power by the power button on the front panel. (2) Press on the Auto adjustment button while switching on the monitor’s power. [How to unlock] (1) Switch off the moni
ページ19に含まれる内容の要旨
English Unlock function after calibration The calibration is available when using the specified optional calibration kit (p.37). After the calibration, the functions below are automatically locked. Locked function Brightness adjustment (including the adjustment by left and right buttons on the front panel) Range adjustment LUT Setting Signal selection button (Color / Monochrome) Unlock function is available by using ScreenManager. [How to unlock] (1) Select the of me
ページ20に含まれる内容の要旨
English 4. ADJUSTMENT 4-1. Screen Adjustment NOTE Allow the LCD monitor to stabilize for at least 20 minutes before making image adjustments. When connecting the digital graphics board, see page 23. Analog Input Screen adjustments for the LCD monitor should be used in suppressing screen flickering and also for adjusting the screen to its proper position. There is only one correct position for each display mode. It is also recommended to use the ScreenManager function when first insta
