ページ1に含まれる内容の要旨
- For Administrator -
For Microsoft Windows CE.NET
Version E
Touch Panel
LCD Monitor integrated
Windows-based Terminal
Please confirm the version of the software built in eClient, and refer to
the suited User's Manual (Refer to the User's Manual Version List on
next page).
This is the manual for the following software version.
* Microsoft Windows CE: 4.10 Rev. 2.7.1 or later
* Microsoft Terminal Server Client: Ver. 7.2.0 or later
* ICA Client: Ver. 7.23 or later
ページ2に含まれる内容の要旨
User’s Manual Version List A handling description changes with versions of the software built in eClient. Please refer to below. NOTE • The version of software built in eClient can be checked with a [System]-[ICA] tab of [Terminal Properties]. OS: Microsoft Windows CE .NET Software Microsoft ICA Client Microsoft Windows CE Windows Software Manual Terminal Server E 4.10 Rev.2.7.1 or later Version 7.2.0 or later Version 7.23 or later (This manual) Version 6.30 D 4.10 Rev.2.6.0
ページ3に含まれる内容の要旨
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2003-2004 EIZO NANAO CORPORATION. All r
ページ4に含まれる内容の要旨
TABLE OF CONTENTS 1. INTRODUCTION..................................................................................... 5 1-1. General Description ......................................................................................5 1-2. Features ........................................................................................................5 1-3. Package Contents..........................................................................................6 1-4. Controls & Connectors .
ページ5に含まれる内容の要旨
1. INTRODUCTION Thank you very much for purchasing the EIZO eClient 630LT-GR/630LT-GR-N. 1-1. General Description The eClient 630LT-GR/630LT-GR-N connects with a Windows Terminal Server*, which installed Microsoft Windows NT Server 4.0 Terminal Server Edition or Windows 2000 Server/Advanced Server/Datacenter Server, and this product is used as a terminal using them. eClient 630LT-GR/630LT-GR-N Windows Terminal Server (WTS) Output data of applications Input data from mouse/keyboard
ページ6に含まれる内容の要旨
1-3. Package Contents Please make sure that all the items listed are in the package. Please contact your local dealer for assistance if any of the listed items are missing or damaged. • eClient 630LT-GR/630LT-GR-N • Mouse (FDM-310) • Power Cord • Screw (M4 x 12 mm) x 4 • User’s Manual (includes Limited Warranty) • 2 Stickers of the Brightness Control Guide • Stylus NOTE • A keyboard is not included. Please purchase it separately. Please use the enclosed mouse. E
ページ7に含まれる内容の要旨
1-4. Controls & Connectors Front (1) (2) (4) (3) (1) Power button (2) Power Indicator Color 630LT-GR/630LT-GR-N status Green • Operation • Screen saver mode Yellow Power save mode Off • Power off (Wake on LAN standby) (3) Speakers (4) Volume Control NOTE • When turning off/on the unit, leave the unit off for a few seconds before turning it on again. 1. INTRODUCTION 7
ページ8に含まれる内容の要旨
Rear (16) (14) (17) (15) (13) (10) (12) (6) (8) (11) (5) (7) (9) (5) Mouse Connector (6) Keyboard Connector (7) Serial Port (RS-232C) (8) Parallel Connector (9) Power Connector (10) Ethernet Connector (10 Base-T, 100 Base-TX) (11) Headphone Connector (12) Microphone Connector (13) USB Port (Downstream) x 2 (14) PC Card Slot 1 (15) Security Lock* 2 (16) Holes for Mounting an Arm Stand* (17) Stand (Detachable) 1 * This allows for connection of a security cable. This lock
ページ9に含まれる内容の要旨
2. CONNECTING THE eClient 630LT-GR/630LT-GR-N This chapter explains how to connect the eClient 630LT-GR/630LT-GR-N to a WTS. 2-1. Setting up the eClient 630LT-GR/630LT-GR-N Please observe the following cautions when connecting the 630LT-GR/630LT-GR-N. WARNING Place the eClient 630LT-GR/630LT-GR-N on a strong, stable surface. A unit placed on an inadequate surface may fall, resulting in injury or equipment damage. If the unit falls, disconnect the power immediately and have the u
ページ10に含まれる内容の要旨
1. In case of connecting the WTS through LAN: Connect the eClient 630LT-GR/630LT-GR-N to the network with an Ethernet cable. In case of a dial-up or dial-in connection: Connect the eClient 630LT-GR/630LT-GR-N to a modem or a modem card. NOTE • Please remove the lid on the side of the 630LT-GR/630LT-GR-N before connecting a LAN card or a modem card. 2. Plug a keyboard and a mouse into the eClient 630LT-GR/630LT-GR- N. If using other devices, please connect them to the appropriate
ページ11に含まれる内容の要旨
3. SETTING UP the eClient 630LT-GR/630LT-GR-N This chapter presents how to prepare for a connection with a WTS when the eClient 630LT-GR/630LT-GR-N starts up for the first time. 1. Turn on the eClient 630LT-GR/630LT-GR-N. The power indicator turns green and a picture appears on the screen. NOTE • When no picture is displayed, or when the message (No keyboard connected. / No mouse connected.) is shown on the screen, please refer to “8. Troubleshooting” on page 61. (In use of a stylus
ページ12に含まれる内容の要旨
3. “Calibration measured” window is displayed when you finished. Click the “Enter” key to accept the settings. 4. “eClient Setup Wizard” is displayed. (Set up the 630LT-GR/630LT-GR-N according to directions of the displayed dialog box.) 12 3. SETTING UP the eClient 630LT-GR/630LT-GR-N
ページ13に含まれる内容の要旨
5. End User License Agreement page is displayed. Read the content and click [Accept] to continue. 3. SETTING UP the eClient 630LT-GR/630LT-GR-N 13
ページ14に含まれる内容の要旨
6. Set up the network environment. [Terminal Name] ................Type the name to identify this unit on the network. Click [Network Properties] and set up connection information according to the connection method to WTS/Web server. Connection method Reference page p.15 • In case of connecting the WTS/Web through Built-in LAN p.15 • In case of connecting with a NE2000 compatible LAN card: p.16 • In case of connecting with a Cisco wireless LAN card/ Agere wireless LAN card: p
ページ15に含まれる内容の要旨
Example; In case of connecting with a NE2000 compatible LAN card In case of connecting the WTS/Web through Built-in LAN: (1) Double-click [Built-in LAN] icon. [IP Address] ........................Type the IP address of the unit. [Name Servers] ...................Type the IP address of each server when DNS or WINS is used. [Advanced]..........................Type the transmission speed and MAC Address of a network. In case of connecting with a NE2000 compatible LAN card:
ページ16に含まれる内容の要旨
In case of connecting with a Cisco wireless LAN card/Agere wireless LAN card: (1) Double-click [CISCO1]/[WLAGS461] icon. [IP Address] ........................Type the IP address of the unit. [Name Servers]....................Type the IP address of each server when DNS or WINS is used. [Wireless Networks] ...................................Set the connection setting with a wireless LAN card. NOTE • In case of selecting [Obtain an IP address via DHCP], deactivate the built-in LAN
ページ17に含まれる内容の要旨
In case of a dial-up connection: (1) Double-click [Make New Connection] icon. (2) Type a name for the connection and select the connection type (Dial-Up Connection). (3) Select a model, set up the TCP/IP settings and Security settings. (4) Type the phone number for the connection. (5) In case of a dial-up connection, the information of local location needs to be set up. Set up the information in the later procedure 8. NOTE • In using the following case, set up in addition to the WTS/We
ページ18に含まれる内容の要旨
7. Set up the desktop area. [Desktop Area and Refresh Frequency] ...................................Set the resolution/refresh rate. (630LT-GR/630LT- GR-N supports 1024 x 768 @60 Hz only). [Desktop Colors].................Set the desktop color (256 Colors / High color) of the following. - Windows CE desktop (before WTS connection) - Windows desktop (after a WTS connection with RDP protocol) NOTE • [High Color] setting after WTS connection can be available only when connecting with
ページ19に含まれる内容の要旨
8. Set up the browser connection. Set up if you are setting up a web browser connection. (1) Select [Internet Options] icon and click [Open]. [General].............................Set up the browser. [Connection].......................Set up the connection method to the browser. [Security].............................Set up the security for the connection to the browser. [Advanced]..........................Set up the display method of the browser. 9. Set up the printer. Set up if
ページ20に含まれる内容の要旨
10. Setup the Local sender’s setting Setup if you are connecting to WTS/Web server by dial-up connection. (1) Select [Dialing] icon and click [Open] icon. [Location name]..................Choose the sender’s location (click [New] to add a new sender’s location). [Local Settings are:].............Setup the local settings. 11. The last page of the “eClient Setup Wizard” is displayed. Click [Finish]. Click [Yes] if a “Terminal Settings change” dialog box is displayed. The “Termin
