ページ1に含まれる内容の要旨
+
FP71G/FP71G
LCD Color Monitor
17.0" (43.2 cm) LCD Panel Size
User’s Manual
Welcome
ページ2に含まれる内容の要旨
i Copyright Copyright © 2004 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation. ii Disclaimer BenQ Corporation makes no representations or warranties, either expressed or implied, with res
ページ3に含まれる内容の要旨
i Table of Contents Getting started ...................................................................................................................... 4 Getting to know your monitor ............................................................................................ 5 Front View ...................................................................................................................5 Back View .................................................................................
ページ4に含まれる内容の要旨
P / 1 1 1 Getting started 1 When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement. BenQ LCD Monitor Quick Start Guide CD-ROM Power Cord Signal Cable: D-Sub Warranty Card Getting started 4 N : 5 3 . L 9 0 0 3 . 0 0 2
ページ5に含まれる内容の要旨
1 1 2 Getting to know your monitor 1 Front View Back View 1 2 1. Power AC input jack 2. Video signal input jack 5 Getting to know your monitor
ページ6に含まれる内容の要旨
1 1 3 How to install your monitor hardware 1 If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to the monitor until instructed to do so. 1. Attach the monitor base. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the moni
ページ7に含まれる内容の要旨
3. Connect the power cable to the monitor. Plug one end of the power cord into the socket labelled ’POWER IN’ on the rear of the monitor. Do not connect the other end to a power point just yet. 4. Route the cables via the loose bracket. Release the cable retaining clip by squeezing the clip inwards as illustrated. Position the cables together and reinsert the clip over them to retain the cables neatly in place behind the monitor stand. 7 How to install your monitor hardware
ページ8に含まれる内容の要旨
5. Connect-to and turn-on the power. Plug the other end of the power cord into a power point and turn it on. Turn on the monitor by pressing the power button on the front of the monitor. Turn on the computer too, and follow the instructions in Section 4: How to install your monitor's software to install the monitor software. How to install your monitor hardware 8
ページ9に含まれる内容の要旨
How to detach the stand base 1. Prepare the monitor and area. Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and control
ページ10に含まれる内容の要旨
1 1 4 How to install your monitor’s software 1 You need to set up the correct monitor driver to suit your operating system. To set up Windows 98, start on this page. Windows 2000, turn to page 11. Windows ME turn to page 12. Windows XP turn to page 13. Windows 98. To manually install or update the driver, perform the following steps: 1. Open the control panel and double-click “Display” icon. 2. From the “Display Properties” window, select the “Settings” tab. Click the “Advanced...” button in th
ページ11に含まれる内容の要旨
Windows 2000. The first time you start Windows with a new monitor, the system will detect it and automatically start the “Add New Hardware Wizard”. Carry out the instructions beginning at step 4. 1. Insert “BenQ LCD Monitor” CD-ROM into your CD-ROM Driver. 2. Click “Start” then “Settings”. 3. Open the Control Panel and double click on the “Display” icon. 4. From the “Display Properties” window, select the “Settings” tab. Click the “Advanced Properties” button in the bottom right corner. 5. S
ページ12に含まれる内容の要旨
Windows ME. To manually install or update the driver, perform the following steps: 1. Click “Start”, “Settings”, “Control Panel” and then double-click “Display”. 2. In the Display Properties window, click the “Settings” tab and click “Advanced... ”. 3. Click the “Monitor” tab and then click “Change”. 4. “Update Device Driver Wizard” dialogue box appears. Choose “Specify the location of the driver (Advanced)” and then click “Next”. 5. Choose “Display a list of all the drivers in a specific locat
ページ13に含まれる内容の要旨
Windows XP. 1. Right click mouse on the desktop and choose “Properties”. Select “Settings” tab and click the “Advanced” button. A small window will pop up. Select the “Monitor” tab in the new window and then click “Properties”. 2. Select “Driver” tab and then click “Update Driver…” 3. The “Hardware Update Wizard” will pop up. Then click “Next”. 4. Select “Don’t search. I will choose the driver to install” and then click “Next”. 5. In the next window, click “Have Disk…”, an “Install From Disk”
ページ14に含まれる内容の要旨
1 1 5 Choosing the best picture resolution 1 Due to the nature of LCD display technology, the picture resolution is always fixed. The best + picture possible for your FP71G/FP71G is achieved with a resolution of 1280x1024. This is called “Native Resolution” or maximal resolution - that is, the clearest picture. Lower resolutions are displayed on a full screen through an interpolation circuit. However flaws do occur with the interpolated resolution. So if you want to have all the advantages o
ページ15に含まれる内容の要旨
3. Select a resolution of 1280x1024. Then click “Apply”. 4. In the subsequent windows, press “OK” and “Yes” 5. You can now close “Display Properties”. 15 Choosing the best picture resolution
ページ16に含まれる内容の要旨
1 1 6 How to choose the right Refresh Rate 1 You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer. There is a table with the factory modes in this user’s guide. Youc an choose 60, 70 and 75 Hertz, (but not 72Hz) for the native resolution of 1280x1024. In Windows 98/2000/ME/XP you can change the refresh rate as fo
ページ17に含まれる内容の要旨
2. From the “Display Properties” window, select the “Settings” tab. Click the “Advanced...” button in the bottom right corner. 17 How to choose the right Refresh Rate
ページ18に含まれる内容の要旨
3. Select the “Adapter” tab. The refresh rate selection field is located in the center at the bottom of the window. 4. Choose a refresh rate from the table with the factory modes, which can be found in the user’s guide, and select this in the settings field. 5. In the subsequent windows press “Change”, “OK” and “Yes”. 6. You can now close “Display Properties”. How to choose the right Refresh Rate 18
ページ19に含まれる内容の要旨
1 1 7 How to set the Picture Optimization 1 The easiest way to obtain an optimal display is to use the ikey function. Press the “ikey” on the control panel and the monitor will adjust automatically. If you are still not satisfied with the result, you can still adjust the image manually. 1. Run the test program auto.exe from CD-ROM; this is the best way to observe possible changes. You can also use any other image, such as the desktop of your operating system. However, we rec- ommend that you
ページ20に含まれる内容の要旨
1 1 8 How to adjust your monitor 1 A Look at the Control Panel 1 2 3 4 5 6 There are 6 keys for user’s control including “iKey”, “Exit”, “Enter”, “<” and “>” key and a power swith. The following descriptions are the introduction of these keys & switch. 1. “iKey” : Adjust vertical position, phase, horizontal position and pixel clock automatically. 2. “Exit” key: Back to previous menu or exit OSD. 3. (Left) key: For Left/Decrease adjustment. Left key is the hot key for
