ページ1に含まれる内容の要旨
SyncMaster 955b
ページ2に含まれる内容の要旨
Main Page On-Screen Display General Highlight Zone Safety Instructions Troubleshooting Notational Check List Power Q & A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front Preset Timing Modes Rear PowerSaver Bottom Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms Automatic Regulatory Manual Natural Color Base Installation Authority
ページ3に含まれる内容の要旨
Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
ページ4に含まれる内容の要旨
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long Notational periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Power Installation Clean Do not use a damaged or loose plug. Other This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug
ページ5に含まれる内容の要旨
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Put your monitor in a location with low humidity and a minimum of Other dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It cou
ページ6に含まれる内容の要旨
When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. Notational Power (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The Installation antiglare/anti-static surface coating on the CDT may also be affected.) Clean Other Dilute the detergent (1:10 ratio) with water before using. Do not
ページ7に含まれる内容の要旨
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Notational Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This may cause
ページ8に含まれる内容の要旨
Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image.
ページ9に含まれる内容の要旨
Monitor and Stand Power Cord Unpacking Stand Front Rear Bottom Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are Warranty Card included with your monitor. If any items are missing, (Not available in all locations) contact your dealer. User's Guide and Driver Installation CD USB Hub (Option)
ページ10に含まれる内容の要旨
Unpacking Front Rear Bottom 1. Highlight button The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. 2. Exit button Use this button to Exit the active menu or the OSD. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power indicator This light glows green during normal operation, and blinks g
ページ11に含まれる内容の要旨
Unpacking Front Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, video board, 2. Signal Cable video card, or graphics card. Note: See Connecting Your Monitor for further information regarding cable connections.
ページ12に含まれる内容の要旨
Unpacking Front Rear Bottom 1. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Tilt/Swivel Base You can separate the base from the monitor.
ページ13に含まれる内容の要旨
Connecting Your Monitor Installing the Monitor Driver Base Installation 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer do
ページ14に含まれる内容の要旨
Automatic Manual Connecting Your When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor included with this monitor. Driver installation is slightly different from one operating Installing the system to another. Follow the directions as appropriate for the operating system you Monitor Driver have. Base Installation Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.
ページ15に含まれる内容の要旨
4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
ページ16に含まれる内容の要旨
Automatic Manual Windows XP | Windows 2000 | Windows Me | Windows NT | Linux Connecting Your Monitor Installing the When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor Driver included with this monitor. Driver installation is slightly different from one operating Base Installation system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web sit
ページ17に含まれる内容の要旨
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this install
ページ18に含まれる内容の要旨
10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start" , "Setting" , "Control Panel". 2. Double click the "Display" Icon. 3. Choose the "Settings" ta
ページ19に含まれる内容の要旨
opti tion ffor your moniittor.) ) ® ® Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a differ
ページ20に含まれる内容の要旨
Tilt/Swivel Base | Attaching and Removing the Base Connecting Your Monitor With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable Installing the Monitor Driver viewing angle. Base Installation Note: The base is detachable. Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base onto the monitor until the tabs are fully engag
