ページ1に含まれる内容の要旨
SyncMaster 795MB+
Install drivers Install programs
ページ2に含まれる内容の要旨
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended periods of time, set your computer to a screen saver. If the same image is present for long periods of time, Phosphor Burnt can be occ
ページ3に含まれる内容の要旨
Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy obje
ページ4に含まれる内容の要旨
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area. Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children. Do not place the product on the floor. Someone, specifically children could trip over
ページ5に含まれる内容の要旨
Do not use the monitor without the monitor stand. It could break down or cause fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
ページ6に含まれる内容の要旨
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover(or bac
ページ7に含まれる内容の要旨
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small me
ページ8に含まれる内容の要旨
Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire. When moving the monitor
ページ9に含まれる内容の要旨
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor and Stand (Some models include a stand attached.) Manual User's Guide, Warranty Card Monitor Driver, Quick Setup Guide (Not available in all Natural Color software, locations) MagicTune™ software, Highlight Zone III software Cable
ページ10に含まれる内容の要旨
Power Cord Stand Stand Front Power button/ Use this button to turn the monitor on and off. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. The Highlight Zone ensures clear images on TVs, video Highlight conferencing systems or photos by emphasizing a certain area on the screen. Use this button to Exit the active menu or the OSD. / Exit / MagicBright Use this button to exit
ページ11に含まれる内容の要旨
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. Rear (The configuration at the back of the monitor may vary from product to product.) Power port Connect the power cord for your monitor to the power port on the back of the monitor. Signal Cable Connect the signal cable to the video port on your compu
ページ12に含まれる内容の要旨
Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Power port Connect the power cord for your monitor to the power port on the back of the monitor. Tilt/Swivel Base You can separate the base from the monitor.
ページ13に含まれる内容の要旨
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Connecting to a computer Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Connecting to a new Macintosh Connect the monitor to the Macintosh computer using the D-SUB connection cable. 2-3. Connecting to an old Macintosh Connect your monitor to the Macintosh using the adapter for Macintosh
ページ14に含まれる内容の要旨
Tilt/Swivel Base With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. The base is detachable. Attaching and Removing the Base If your monitor was supplied with the base detached, attach the base as follows. Remove the twist-tie before attaching the base to the monitor.
ページ15に含まれる内容の要旨
Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base onto the monitor until the tabs are fully engaged in the slots. 4. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap. Removing the Base 5. Squeeze and pull up on the release latch on the base. 6. Push the base toward the
ページ16に含まれる内容の要旨
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo and this installation doesn't damage
ページ17に含まれる内容の要旨
Windows XP | Windows 2000 | Windows Me | Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) http
ページ18に含まれる内容の要旨
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the " " button. Then Continue Anyway click " " button. OK This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted
ページ19に含まれる内容の要旨
10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start" , "Setting" , "Control Panel". 2. Double click the "Display" Icon.
ページ20に含まれる内容の要旨
® ® Microsoft Windows NT Operating System 1. Click , , , and then double-click icon. Start Settings Control Panel Display 2. In Display Registration Information window, click Settings Tab and then click All Display . Modes 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (low
